Wasserstein Smart Floodlight User manual

Smart Floodlight
User Manual

Page 1
In the Box
1 x smart floodlight
1 x ring and nut set
2 x machine screws
(M4 * 25mm)
3 x wire nuts
1 x crossbar
1 x EVA gasket

• As the temperature changes, the detection distance will be
affected.
• Do not mount the near a heat source like an air conditioner,
vent, furnace, exhaust, or in a direction facing any reflective
object / other nearby light source.
• Shut off power at the circuit breaker or fuse panel before
removing the old fixture or installing the new one.
• LEDs can be damaged by electric static. Before installing,
discharge any static from your body by touching a grounded
bare metal surface.
• To avoid damage, do not remove the clear lens over the LED
module.
Page 2
• Please read this entire manual before attempting to
assemble, operate, or install the product.
• Floodlight MUST be installed by a qualified electrician.
• Turn power OFF before installing.
• Do NOT touch or install fixture near water or if the
surrounding area is wet.
• Do NOT remove the protective LED lens.
• Do NOT look directly at lit LEDs for any length of time.
• Do NOT leave bare wires exposed.
• Electrical requirements: 120V, 60 Hz
• Do NOT allow the sensor head to touch the LED head
housing. Maintain at least 1 inch of space between the LED
heads and the sensor head.
• For proper operation and protection against water damage,
the motion sensor adjustment controls MUST be facing
downward.
• Do NOT mount below 5 ft.
Safety Instructions
Warnings

Page 3
2. Remove the protective layer from the EVA gasket and stick it
firmly on the back of the floodlight (make sure the long screw
at the crossbar goes through the center hole and the wires go
through the gasket opening).
Caution:
The floodlight must be installed by a qualified electrician. Your
main circuit breaker MUST be turned off before installing.
How to Install
1. Attach the crossbar to the junction box using the two machine
screws provided.

Page 4
3. Connect the yellow/green (ground) wire from the floodlight to
the junction box using the ground screw (painted green).
Connect the white wires (neutral) with a wire nut. Connect the
black wires (hot) with a wire nut.
4. Carefully place wires into the junction box. Place floodight
over the crossbar. Mount the floodlight onto the crossbar and
secure it with the nut and ring provided.
Note:
For further weatherproofing, fill all gaps with a sealing compound
or silicon glue.

Page 5
Minimum requirements:
• Smartphone or tablet running iOS 9.0 or later / Android
5.0 or later.
• 2.4 GHz WiFi Network (not compatible with 5 GHz
connections).
• Upload speed of at least 2 Mbps.
1. Download the App by scanning the QR code or by searching
"Wasserstein App" in Google Play or the App Store.
2. Sign up for a new account or log in to an existing account.
3. Click "Add Device" or "+" in the top right corner. You can add
your device by selecting "Add Manually" or "Auto Scan".
App Setup

Page 6
Figure 1
Flash Dim Flash Dim
1. Select "Lighting" - "PIR Light（BLE+WiFi)".
2. Reset the floodlight by turning it on and off in the following
sequence: on-off-on-off-on (steps also displayed in your App).
Then, your floodlight will flash in intervals (Figure 1).
Add Manually
selection
If the light is flashing already,
please skip the reset steps.
Resetting the device:
1. Power on the device.
2. Turn on-off-on-off-on.
3. Make sure the light is flashing.
Note: Please complete the network
selection within 3 minutes after
resetting the device.
Confirm that the light is flashing.

Page 7
3. Enter your WiFi details, and click "Confirm".
4. Wait until your device has been added successfully.
Wasserstein Smart Floodlight
WiFi Login
WiFi Password

Page 8
1. Reset the floodlight to enable pairing mode. Turn on and off
in the following sequence: on-off-on-off-on. Your floodlight
will then flash in intervals.
2. Wait until your floodlight has been automatically detected.
Auto Scan

Note: Display and interface are subject to change.
Sensor
Manual
On/Off
Light intensity
Floodlight color
Turn on/off timer
Schedule
Sensor
On/Off
Motion detection range
Floodlight light sensitivity
Duration of light flash
Event records
1. Settings
App Functions
Page 9

Page 10
2. How to Use Linked Devices
On the ‘Sensor’ page click "Linked Devices"，then click "+" on
the lower right corner to enter the ‘Create New Smart’ page.
Here, you can add multiple trigger conditions and tasks for
your floodlight to perform.

Page 11
3. Third-Party Control (Google Assistant & Amazon Alexa)
Follow the instructions in the App to link to your Google
Assistant or Amazon Alexa. Examples of voice commands
are also available in the App.

Page 12
1. The smart floodlight will not turn on. What's going on?
• Check the connection to your home power source.
• Set the floodlight to "Manual" mode and try turning it on
manually.
• Set the light sensitivity to "Day" and see if you can trigger it
by moving. Remember to reset the light sensitivity to your
preference after testing.
• Make sure the App is installed and paired correctly with
your Smart Floodlight.
• Make sure your WiFi network is in 2.4 GHz, not 5 GHz.
2. Will the floodlight turn on during the day?
Yes, to turn on your floodlight during the day, set it to "Sensor"
mode and adjust the light sensitivity to "Day". Or set to
"Manual" mode and you can turn on your floodlight manually,
whether it is day or night.
3. Is a solar panel recommended, or will the plug-in floodlight
keep the camera charged?
A solar panel is not recommended. The AC input will keep the
floodlight powered continuously.
4. After installing the floodlight, how can I confirm that it is
working?
Set it to "Manual" mode, you can turn it on or off whether it
is day or night. Set it to "Sensor" mode and adjust the light
sensitivity to "Day". You can test to trigger it by moving.
Remember to reset the light sensitivity to your preference
after testing.
FAQ

Specifications
Materials:
Motion detection:
Color temperature:
Brightness:
Power:
Frequency:
Waterproof rating:
PC
180° / 63 ft
3000 - 6500K
2000 LM
100 - 120V AC
2.4 GHz
IP65
Get More Support
Scan the QR code below or email us at:
[email protected]
Wasserstein is a trademark of Dropcases Ltd. Made in China
www.wasserstein-home.com