Wasserstein 3-in-1 Wired Floodlight, Charger and Mount for Blink Outdoor /... User manual

3-in-1 Wired Floodlight, Charger
and Mount for Blink Outdoor / XT2
USER MANUAL

In the Box
Safety Information
• Disassembling the light head is not recommended as it may cause damage
• DO NOT remove the protective LED lens.
• DO NOT look at LEDs that are on for any length of time.
to internal components. The floodlight may not function aptly after
disassembling it.
Installing Your Floodlight
Installing the floodlight to the wall plate
1. Install the wall plate on the wall using the 4 screws (included) and the 4
anchors (included).
1
4 x screws
EVA gasket
camera mount adapter
adapter with cable floodlight
US, UK, EU plugs
wall plate long screw
8 x cable clips
4 x wall anchors
USB cable

2
2. Remove the protective tape from the EVA gasket and press the adhesive
side firmly against the rear of the floodlight.
Important: Before mounting the floodlight completely, apply the EVA
gasket. It prevents water from seeping into the wall plate.
3. Mount the floodlight + EVA gasket taped onto the wall plate.
4. Mount the floodlight onto the wall plate and secure it with the long screw
provided.
Remarks: 3 x plug heads are included (US, UK, EU).
5a. Insert the appropriate plug into the adapter; turn clockwise
until it clicks.

3
c. Plug the adapter onto the wall socket to power the floodlight.
6. Peel the adhesive skins then stick the cable clips onto the wall.
Run the wires of the adapter through the cable clips for a better
cable management.
b. Connect the floodlight cable and adaptor cable together, then screw
in the plastic cover.

4
Mounting Your Camera
1. To charge your camera via the floodlight, plug in the USB cable in the
micro-USB port of the camera. Press in firmly.
2. Insert the Blink camera mount adapter.
3. Screw the camera onto the mount.
4. Open the USB port cap of the floodlight and connect the cable. Press in
firmly.
5. Adjust the camera to your preferred viewing angle.
mounting screw
charging port
Important Tips
1. Assess where intruders are most likely to enter and the path they would
take. Most intruders enter the home through a back door, patio door, or
garage door. Therefore, it is advisable to place the floodlight near the
entrances to your home.
2. Mount the floodlight on walls that an intruder would walk alongside, such as
a narrow pathway. The motion sensor works best when movements are
detected parallel to the floodlight, not towards it.
3. You can also mount the floodlight beside your security camera to illumi-
nate the camera’s vision at night.
4. Although the floodlight is weatherproof, it is advisable to mount it to a wall
shaded from the rain and sunlight to maximize battery life.

5
FAQ
Product Specifications
Materials:
Sensor angle range: 120°
Sensor distance thresholds: 13 to 33 ft (4 to 10 m)
Max LED light intensity : 2000 Lumens
Color temperature: 5500-6500k
Power: 100 - 240 AC 50/60Hz
PC + Aluminum
For more information, visit:
www.wasserstein-home.com
or contact us at:
[email protected]
Made in China
Blink Outdoor is not included.
Blink XT2 is not included.
Blink Outdoor is a trademark of Immedia Semiconductor Inc.
Blink XT2 is a trademark of Immedia Semiconductor Inc.
Wasserstein is not affiliated with Immedia Semiconductor Inc.
Wasserstein is a trademark of Dropcases Ltd.
1. The floodlight keeps flashing. What should I do?
2.Will the floodlight turn on during the day?
No, the floodlight will only turn on during the night or when the
surrounding light is dim.
3. Is a solar panel recommended, or will the hard-wired floodlight keep
the camera charged?
4. After installing the floodlight, how can I confirm that it is working?
Try waving your hands in front of the floodlight. If all of your connections
are fine, the floodlight will light up due to the motion. If it does not light
up, please check your wiring, especially if the cable colors match. Or,
allow up to 10 minutes of reset time for the floodlight without triggering
them.
It does not require a solar panel as the hard-wired floodlight’s USB port
will keep the camera powered continuously.
- Check your connection of all three wires to the house power.
- Check the area around the floodlight as it may be detecting motion.