WATER TENDER WTC Specification sheet

6201 South Hanover Rd, Elkridge, MD 21075 | P: 410-796-7700 | F: 410-796-7739 |T: 800-796-7700
WTC TIME CLOCK CONTROL VALVE | QUICK SET UP
Quality Water Treatment Products
®
TIME OF DAY SETTING
Press and hold the SET button for 3 seconds.
The arrow will point to Time.
Press the UP or DOWN arrows to adjust the
hour. The arrow will point to PM for PM
hours only.
Press the SET button.
Press the UP or DOWN arrows to adjust
the minutes.
1
TIME OF REGENERATION SETTING
Press the SET button.
Press the UP or DOWN arrows to adjust
the minutes.
2
Press the SET button. The arrow will jump to
Days to Regen.
REGENERATION FREQUENCY SETTING
Press the UP or DOWN arrows to adjust the
days of regeneration frequency. The factory
setting is every 7 days.
Press the SET button. Screen will now show
the time.
3
4SYSTEM SET UP IS COMPLETE!
When system is operating one of two displays will
be shown: Time or Days to Regen. Pressing the UP
or DOWN buttons will toggle between the two
choices.
See the back of this document for more set up
options and error codes.
Press the SET button.
Press and hold the SET and UP buttons for
3 seconds. The arrow will point to Time.
©WATERTENDER 2016 |WATER-TENDER.COM | WTCFILTER-SETUP
Press the UP or DOWN arrows to adjust
the hour. The factory setting is 1 AM.

6201 South Hanover Rd, Elkridge, MD 21075 | P: 410-796-7700 | F: 410-796-7739 | T: 800-796-7700
WTC TIME CLOCK CONTROL VALVE | MORE OPTIONS
ERROR CODES
Display
E1 (1001)
E2 (1002)
CauseDescription
Defective motor, damaged wiring, or poor wire connection
E3 (1003)
E4 (1004)
Defective motor, damaged wiring, poor wire connection,
or mechanical component failure
Damaged wiring, poor wire connection, or mechanical
component failure
Damaged wiring, poor wire connection, or mechanical
component failure
Unable to recognize start of regeneration
Unexpected electrical or mechanical
stall
Motor running too long or timeout
during piston relocating
Motor timeout when piston is
relocating to service position
MANUAL REGENERATION
For regeneration tonight: press the UP and
DOWN buttons simultaneously. Arrow will point
to Regen.
For immediate regeneration: press and hold the
UP and DOWN buttons simultaneously for 4
seconds. Valve motor will start.
RESET CONTROL VALVE
Take the cover o, power up the valve and
unplug it from the board, not the wall.
Plug it back in after 10 seconds.
©WATERTENDER 2016 |WATER-TENDER.COM | WTCFILTER-SETUP
Make sure the drain line connection meets all plumbing codes and that
the drain line size can handle the backwash ow rate of the lter
Make sure the inlet and outlet on the bypass valve are open.
Make sure the control valve timer is plugged into an electrical outlet
with power 24 hours per day.
Check all piping for leaks.
Connect the WTC control valve transformer into the electrical outlet.
Open the inlet ball valve 25% of its full open position. The water is going to enter the tank
from the bottom of the distributor pipe and leave the tank from the top. This will slowly
purge all the air from the tank. If the water enters the tank too fast, all the lter media
will be ushed to drain during start up.
Press and hold the UP and DOWN arrows simultaneously for 3 seconds until the drive
motor starts. The display will read “C1” backwash position when the drive motor stops.
When only water is running to the drain, open the inlet and outlet ball valves fully.
Press the UP button to advance the control valve to the fast rinse position. The display will
read “C4”.
Once the drive motor stops, press the UP button to advance the control valve to the service
position. The display will read“C0”.
Note: The timer will automatically advance to the service position and the display will read
Time of Day.
SYSTEM START UP FINAL CHECK