Waterdrop WD-BS08 User manual

Quick Connect Under Sink Stainless-steel Water Filtration System
Instruction
Manual
Model No.: WD-BS08
Operating temperature
Working pressure
Flow rate
Feed water requirement
Filter capacity
41-100℉/5-38℃
15-100 psi/100-689 kpa
1.6 gpm/6.0 lpm (tested under 60psi)
Municipal tap water
Up to 1 year/8000 gallons
Specications
Precautions
• Please wear a pair of gloves when installing to avoid scratching your hand.
• Do not use it with water that is microbiologically unsafe or of unknown quality without
adequate disinfection.
• For use only with cold water.
• Do not freeze the filter, as this can cause cracking and water leakage.
• Do not allow children under 3 years old to have access to small parts during installation of this
product.
• This installation must comply with all applicable state and local regulations.
• Turn off the water supply while replacing the filter.
39.3 inches
3/8‘’ tubing
Inlet
Cartridge
Filter head
Fastening
ring
Outlet
Bracket
Quick-connect
fitting
Faucet
39.3 inches 3/8‘’ tubing
Wrench
Teflon tape
3/8‘’-1/2‘’ Converter
3/8‘’-1/2‘’ Converter
Feed water adapter
Filter housing
(Note: Actual life varies according to local water quality.)

Installation of the lter system
How to Use the Quick-Connect Fittings (To connect)
If the tubing is not fully inserted, no seal will be created, and leakage will occur.
When the tubing is fully inserted, put the blue lock clip on the fitting. It will lock the tubing in
place and prevent it from falling off.
Step 1 Mount the Bracket
1. Make sure the arrows on the filter head are consistent with the direction of your water flow.
Unscrew four screws on the filter head then align the holes on the bracket with the holes in the
filter head. Insert four mounting screws included with the system through the bracket and into
the filter head until tight. (Figure 1)
2. Choose a suitable installation position in advance. It can be put on the ground of cabinet or
fixed on one side of cabinet with a bracket.
3. Paste the assistant label to finish drill. Insert two screws in the hole. (Figure 2)
Step 2 Install the Feed Water Adapter (cold water only)
1. Shut off the water supply. Turn on the kitchen faucet to release the water pressure;
Note: Make sure the water has stopped running before proceeding to the next step. Get
a towel or bucket to catch water.
2. Disconnect the cold water pipe from the cold water supply valve;
3. Twist the feed water adapter onto the cold water supply valve (with its washer) and tighten it
with an adjustable wrench;
Note: If the cold water pipe is 1/2", unscrew the two converters from the feed water adapter
firstly (Figure 3), then implement step 3.
4. Twist the cold water pipe (with its washer) onto the feed water adapter and tighten with an
adjustable wrench.
Step 3 Install the Faucet (Figure 4)
Note: If there is no hole in your kitchen sink or countertop,you have to drill one (1") or use the
hole from the soap dispenser.
1. Insert the faucet spout into the faucet body;
2. Insert the faucet stem into the hole on the countertop;
3. Under the sink, slip on other parts in the order shown in the picture;
4. Insert the quick-connect fitting onto the faucet stem fully and firmly.
3/8" Cold
water Pipe
Feed water
adpater
3/8" Inlet
water tubing
Cold water
supply valve
1/2" Cold
water Pipe
Cold water
supply valve
Unscrew
Unscrew
Figure 3
Figure 1 Figure 2

Hot Cold
Filter system
Inlet
Outlet
Step 4 Connect Tubing
1. Install the Inlet Water Tubing (Figure 5)
Connect the inlet water tubing from the feed water adapter to the inlet water port and pop the
lock clip on the fitting;
2.Install the Outlet Water Tubing (Figure 6)
Connect the outlet water tubing from the faucet to the outlet water port and pop the lock clip on
the fitting;
Step 5 Check the Leaks and Flush the Filter
Turn on the cold water supply valve. Check if there’s water leakage at connectors, components,
valve or any connecting position. Then turn on the new faucet. It may dispense muddy or black
water at the beginning. Please flush for 10 minutes continuously.
Note: The water is not drinkable until flushing for 10 minutes.
Cartridge change instructions
Step 1 Remove the Old Cartridge
Turn off the water supply to the system. Open faucet to release the pressure and drain the water.
Take off the cartridge and unscrew the fastening ring using the filter wrench included with your
system. Hold the filter head with one hand and pull off the cartridge with another hand. Remove
and discard the old filter cartridge.
Step 2 Install the New Cartridge
Hold the filter head with one hand and insert the cartridge into the head with another hand until
two black sealing rings are fully inserted and the cartridge reaches the end.
Press the filter head downwards hard into the cartridge. Then screw the fastening ring counter-
clockwise with a wrench. Hang the bracket on the screws.
Step 3 Flush the System
Turn on the cold water supply valve and check if there’s water leakage. Then turn on the faucet. It
may dispense muddy or black water at the beginning. Please flush for 10 minutes continuously.
Quick-connect
fitting on faucet
3/8’’ Outlet water tubing
Figure 6
Figure 4
Faucet Body
Mounting Washer
Nut
Countertop
Faucet Spout
Quick-Connect
fitting
Faucet Stem
Lock clip
Lock clip
Close
Feed water adapter
3/8’’ Inlet water tubing
Figure 5

Frequently asked questions
Q: What should I do if water leaks after installation?
A: In the event of water leakage, turn off the water supply. If the water leakage is occurring at the
thread, wrap Teflon tape on the external thread. If the water leakage is occurring at the quick
connect position, check whether the cut of PE tubing is flat. If it is not flat, re-cut the tubing. Also
make sure the tubing hits the bottom of the fitting. Contact us for solutions if the water leakage
persists.
Q: Why didn't the TDS value lower after ltration?
A: The main purpose of this Waterdrop filter is not to remove TDS. TDS stands for total dissolved
solids, and it is basically composed of inorganic salts and a small amount of organic matter. The
filter can remove harmful substances while keeping beneficial trace elements. Please choose
Waterdrop RO system if you are looking for physical removal of TDS.
Q: When should I replace the cartridge?
A: The filter's service life is related to the water quality. If the flow rate is significantly reduced or if
the water has a peculiar smell, we suggest that you replace the cartridge.
Q: What substances can the lter remove?
A: Our premium coconut carbon block filter can effectively reduce chlorine, taste and odor,
limescale, cysts and other heavy metals.
5-year quality assurance
All mechanical devices with moving parts have a normal life span and will need to be replaced
periodically. For this reason, mechanical devices such as filter housing, filter head, and faucets
have a limited replacement assurance of 5 year.
No assurance is given as to the service life of any filter cartridge, as the service life will vary based
on local water conditions and water consumption.If the product proves to be defective within 5
year from the date of purchase, please contact our customer service department. During the
assurance period, we will replace or repair any part that is deemed to be defective if the product
has not been subjected to tampering, alteration, or improper use after delivery, and has not been
repaired by the manufacturer.We do not make any promises in the event of misuse, use in
abnormal temperature conditions, conditions outside those listed in the operating parameters, or
use in commercial operations.
V010Made in China
Manufacturer Technical Support:
Qingdao Ecopure Filter Co., Ltd.
1-888-352-3558 (U.S.) Mon-Fri 8:00AM-5:00PM (PST)
If you encounter any problem with our product, please contact us
to get support via the purchase channel.