Waterdrop WD-TSB-10 User manual

Figure 3
Figure 1
Figure 4
Figure 2
Step 2: Connect the water supply (cold water only)
1. Shut o the water supply and remove the faucet hose.
2. Connect the feed water adapter and ensure that the rubber O-ring is loaded.
• If the angle valve outlet is 3/8”, connect it to the water supply and faucet hose directly. (Figure 3)
• If the angle valve outlet is 1/2”, you need to remove the above two ttings before connection. (Figure 4)
3. Connect one end of the 1/4" PE tubing to the inlet of the lter head. Until you reach the mark on the
tubing.
Triple Stage Undersink Water Filtration System
WD-TSB-10 system | Installation Instructions
Filter head
Stainless faucet
Quick-connect fitting
Mark for full insert
3/8”-1/2” converter
3/8”-1/2” converter
Feed water adapter
Teflon tape
1/4” tubing
3/8" Cold water valve 1/2" Cold water valve
Note: The service life mentioned above is subject to chlorine reduction. Actual result varies according
to the local water quality.
Precautions
• Do not use it with water that’s microbiologically unsafe or of unknown quality without adequate disinfection.
• For use only with cold water.
• Do not freeze the lter, as this can cause cracking and water leakage.
• Do not allow children under 3 years old to have access to small parts during installation of this product.
• This installation must comply with all applicable state and local regulations.
• Turn o the water supply while replacing the lter.
Operating temperature
Working pressure
Flow rate
Filter capacity
2-38℃/35-100℉
10-125psi (0.7-8.6bar)
1gpm
Specifications
Feed water requirement Municipal tap water
WD-10PP: up to 6 months
WD-10GC: up to 8-12 months
WD-10CT: up to 12-18 months
WARNING Please read it carefully before installation.
Installation of the filter system
Tips: How to use the quick-connect?
To connect: There is an existing mark at the end of the tubing for you to conrm if the tubing is fully
inserted into the tting. (Figure 1)
To disconnect: Use your thumb and index nger to press down on the lock sleeve. Use your other hand to
pull out the hose from the tting. (Figure 2)
Note: Please do not pull out the tubing directly, or else it will damage the tting and cause leakage.
Step 1: Fix the filter head and the filter
1. Paste the assistant label to nish drilling.
Note: Mount the water lter at least 2 inches higher
than the ground for easier lter change.
2. Install the screw and reserve enough space to hang the lter.
3. Hang the lter system on the screw.
Press
Pull
Press

Q: Why doesn’t the TDS value lower after filtration?
A: The main purpose of this waterdrop lter is not to remove TDS. TDS stands for total dissolved solids,
and it is basically composed of inorganic salts and a small amount of organic matter. The lter can
remove harmful substances while keeping benecial trace elements. Please choose Waterdrop RO
system if you are looking for physical removal of TDS.
Q: When should I replace the filter?
A: The lter’s service life is related to the water quality. If the ow rate is signicantly reduced or if the
water has a peculiar smell, we suggest that you replace the lter. The recommended service life of the
lter is as follows: The PP lter has a 6 month lifetime; the GC lter has an 8-12 months lifetime; the CT
lter has an 12-18 months lifetime.
Q: What substances can the filter reduce?
A: Our premium coconut carbon block lter has been tested by an independent laboratory against
NSF standards. It can eectively reduce chlorine, taste and odor, cysts, hydrogen sulde, and other
heavy metals.
Q: What is the difference between the WD-TSA system and the WD-TSB system?
The WD-TSA system does not come with a faucet. It will connect to your existing faucet. Meanwhile,
the WD-TSB system comes with an additional water faucet.
1 -year quality assurance
All mechanical devices with moving parts have a normal life span and will need to be replaced periodically. For
this reason, mechanical devices such as water ttings, lter head, and faucets have a limited replacement
assurance of 1 year. No assurance is given as to the service life of any lter cartridge, as the service life will vary
based on local water conditions and water consumption.
If the product proves to be defective within 1 year from the date of purchase, please contact our customer
service department. During the assurance period, we will replace or repair any part that is deemed to be
defective if the product has not been subjected to tampering, alteration, or improper use after delivery, and
has not been repaired by the manufacturer.
We do not make any promises in the event of misuse, use in abnormal temperature conditions, conditions
outside those listed in the operating parameters, or use in commercial operations.
Customer service:
1-888-352-3558 Mon-Fri 8:00 AM-5:00 PM (PST)
[e-mail]
www.waterdroplter.com (live chat available) Made in China V003
Step 3: Install the faucet
Note: If there is no hole in your kitchen sink or countertop,
you have to drill one (1")or use the hole for the soap
dispenser.
1. Insert the faucet spout into the faucet body.
2. Insert the faucet stem into the hole on the countertop.
Under the sink, slip on other parts in the order shown in
the picture.
3. Firmly insert the quick-connect tting onto the faucet
stem.
4. Connect one end of the tubing to the quick-connect
tting of the faucet, then lock the clip. If you want to pull
out the tubing, remove the clip rst.
5. Connect the other end to the outlet of the lter head.
6. Push the tubing into the tting until you reach the
mark on the tubing.
Step 4: Flush the filter and Check the leaks
1. Flush the lter for 5 minutes before use.
2. In the event of water leakage, turn o the water
supply. If the water leakage is occurring at position 1,
wrap Teon tape on the external thread. If the water
leakage is occurring at position 2, 3 or 4, check whether
the tubing is fully inserted into the ttings. If not, insert
it again until you reach the mark on the tubing.
Filter replacement
1. It’s recommended to turn o the water supply and
turn on the faucet to release the water pressure.
2. Rotate 1/4 turn to the left to remove the lter.
3. Take out the new lter and remove the protective cap.
4. Rotate 1/4 turn to the right to install the lter. Ensure
that the lter’s triangle mark is aligned with the connection
mark.
5. Turn on the cold water valve and ush for 5 minutes.
Mounting washer
Countertop
Nut
Faucet spout
Quick-connect
fitting
Faucet body
Faucet stem
Clip
Clip
Frequently asked questions
Q: What should I do if water leaks after installation?
A: In the event of water leakage, turn o the water supply. If the water leakage is occurring at the
thread, wrap Teon tape on the external thread. If the water leakage is occurring at the quick
connection position, insert the quick-connect tting to the end and make sure the hoses hit the
bottom of the tting. Contact us for solutions if the water leakage persists.
Hot Cold
Filter system
Inlet Outlet
134
2
Remove the filter Install the filter