Waterpik Sonic-Fusion 2.0 SF-03 User manual

Waterpik®Sonic-Fusion®2.0
Models SF-03 | SF-04
Waterpik®Sonic-Fusion®2.0
Modèles SF-03 | SF-04
Sonic–Fusion 2.0
Brush
Floss
Speed
Waterpik®Sonic-Fusion®2.0
Modelos SF-03 | SF-04
Sonic–Fusion 2.0
Brush
Floss
Speed
www.waterpik.com

2
IMPORTANT SAFEGUARDS
IMPORTANT
SAFEGUARDS
READ ALL INSTRUCTIONS
BEFORE USING.
• This product is for household use.
When using electrical products, especially
when children are present, basic safety
precautions should always be followed,
including the following:
DANGER:
To reduce the risk of
electrocution:
• Do not handle plug with wet hands.
• Do not place in or drop into
water or other liquid.
• Do not use while bathing.
• Do not place or store product
where it can fall or be pulled
into a tub or sink.
Sonic–Fusion2.0
Brush
Floss
Speed
• Do not reach for a product that has fallen
into water. Unplug immediately.
• Check the power supply cord for damage
before the rst use and during the life of
the product.
• The supply cord cannot be replaced. If the cord
is damaged the appliance should be scrapped.
WARNING:
To reduce the risk of burns,
electrocution, ire, or injury to
persons:
• If product is opened/disassembled for ANY
reason, warranty is VOID.
• Do not use this product if it has a damaged
cord or power supply, if it is not working
properly, if it has been dropped or damaged,
or dropped into water. Contact Water Pik, Inc.
or visit www.waterpik.com.
•
Do not direct water under the tongue, into the
ear, nose or other delicate areas. This product
is capable of producing pressures that may
cause serious damage in these areas.
• Do not direct water into the nose or ear.
The potentially deadly amoeba, Naegleria
fowleri, may be present in some tap water or
unchlorinated well water and may be fatal if
directed into these areas.
• Use this product only as indicated in these
instructions or as recommended by your
dental professional.
• Only use ossing brush heads and accessories
recommended by Water Pik, Inc.
• Do not drop or insert any foreign object into
any opening or hose.

ENGLISH
3
• Keep electrical cord away from
heated surfaces.
• Do not use outdoors or operate where aerosol
(spray) products are being used or where
oxygen is being administered.
• Fill reservoir with water or other dental
professional recommended solutions only.
• Remove any oral jewelry prior to use.
• Do not use if you have an open wound on your
tongue or in your mouth.
•
If your physician or cardiologist has advised
you to receive antibiotic premedication before
dental procedures, you should consult your
dentist and/or medical professional before
using this product or any other oral hygiene aid.
• Do not use iodine or water insoluble
concentrated essential oils in this product.
Use of these can reduce product performance
and will shorten the life of the product.
Use of these products may void warranty.
• Close supervision is necessary when
this product is used by, on or near children
or invalids.
• Magnetic eld: Pacemakers and similar
implanted medical devices may be aected
by magnet. Contact your doctor with
any questions.
• Do not use the toothbrush motor for more
than 5 minutes in each 10 minute period.
• Children should be supervised to ensure that
they do not play with the appliance.
• This product does not contain any user
serviceable parts. Do not attempt to open.
• Using toothpastes containing peroxide may
damage the plastic housing of this product.
• Using abrasive or chemical cleaners may
damage the plastic housing of this product.
• IMPORTANT This device uses wireless
communication to control the ON/OFF
function of the water osser pump motor
from the toothbrush power handle. To avoid
electromagnetic interference, do not operate
this device in restricted locations such as
aircra or specially marked areas in hospitals.
SAVE THESE
INSTRUCTIONS

4
5
6
TABLE OF CONTENTS
Product Description
Preparing The Unit
Brushing and Flossing
Care and Maintenance
Limited Three-Year Warranty
6
8
10

ENGLISH
5
Brush
Floss
Speed
•
8
•
6
•
4
•
2
•
PRODUCT DESCRIPTION
1. Brush head
2. Water fosser nozzle
3. Hinged lid
4. Reservoir
5. Water hose
6. Water fosser pressure control dial
7. Water hose release button
8. Toothbrush ON/OFF button 2
9. Motion activated ring lights* 1
10. Water fosser ON/OFF button
11. Toothbrush speed control
12. Toothbrush speed indicator Lights
13. Toothbrush charge indicator lights
14. Power cord
15. Charging base
16. Wireless connection light
17. Magnetic brush head holder*
Recommendation:
replace brush
head every 3
months
Compact
size brush
head
Full
size brush
head*
3
8
9
4
10
17
11
12
5
13
6
14
15
7
16
Replacement brush heads may be purchased online at www.waterpik.com, *select models only
or by phone from Water Pik, Inc. at 1-800-525-2774 (USA). To nd detailed
information please visit our website at www.waterpik.com.

6
Floss
Brush
•
8
•
6
•
4
2
•
•
PREPARING THE UNIT / BRUSHING AND FLOSSING
Brush Brush
Click
Click
Brush
Floss
Speed
Floss
Speed
Sonic–Fusion2.0
Brush
Floss
Speed
Sonic–Fusion 2.0
Blue
Light
Fill
PREPARING THE UNIT
Powering the Unit
Plug the cord into an electrical outlet. If the outlet is controlled by a wall switch,
be sure it is turned on.
Attaching the Brush Head to the Power Handle
Position the brush head on the power handle as shown. Press rmly until it clicks into
place. To remove, rmly pull the brush head to separate it from the power handle.
Attaching the Power Handle to the Hose
Position the power handle onto hose in the base. Press the power handle rmly onto
the hose attachment until it clicks into place. To remove, simply press the round
button on the back side of the power handle.
Charging the Sonic-Fusion® 2.0 Power Handle
For a full charge, leave the handle on the charging base for at least 4 hours. If the
toothbrush is to be stored for an extended period of time (six months or more),
be sure to fully charge it (at least 4 hours) prior to storage.
Charge Lights
Toothbrush charge indicator lights will indicate level of battery charge for
approximately 10 seconds aer removal from the charging base and aer use, and
will then turn o. If only the bottom light is lit, then recharging is recommended to
ensure uninterrupted use.
Wireless Connection Light
Blue light indicates the osser base unit is communicating via Wireless
Communication and is “Ready” for activation via FLOSS button.
Preparing the Reservoir
Remove reservoir and open hinged lid. Fill the reservoir with warm water. Close the
lid and replace the reservoir on the base and press rmly.
Prime Unit (First Time Use Only)
Floss Point tip into sink. Press FLOSS button to turn water on. Rotate pressure knob
repeatedly between high and low until water ows. Aer water ows from the
nozzle, press the FLOSS button to turn water OFF.
Rotate

ENGLISH
7
Brush
Floss
Brush
Floss
Speed
Brush
Floss
Speed
Adjust
Brush
Brush
30 sec.
30 sec.
30 sec.
30 sec.
Speed
Floss
Speed
Sonic–F
Floss
Brush
& Floss
BRUSH
Place the brush head in your mouth before pressing the BRUSH button.
Recommended Technique
For best results, position brush along gumline at a 45-degree angle. Press the BRUSH
button to turn the brush ON. Use light pressure and move the toothbrush slowly
allowing for the sonic action to clean each tooth individually. Brush can be easily
disconnected from the hose if desired (See diagram onproduct description page).
Quad Timer
The Sonic-Fusion® 2.0 will create a short pause every 30 seconds to remind you to
move to the next section of your mouth. You will brush the outside of the teeth for
30 seconds and then the inside for 30 seconds. This will be repeated on the other
arch for a total of 2 minutes to clean all teeth.
2-Minute Timer
The brush will automatically shut o aer 2 minutes of run time.
Brush Speeds
The Sonic-Fusion® 2.0 toothbrush gives you the option to choose between two brushing
speeds: High and Low. If you wish to change to a dierent speed, you can do so by
pressing the Speed button while brushing. The LED’s below the Speed button indicate
the current selection. High: 2 LEDs ON, Low: 1 LED ON.
FLOSS
Always place the brush head in your mouth prior to pressing the FLOSS
button. Lean over the sink and slightly close lips enough to prevent splashing
while still allowing water to ow from mouth into sink.
Adjusting the Pressure Setting
Turn the water osser pressure control dial on the base of the unit to the lowest
setting (pressure setting No. 1) for rst-time use. Gradually increase pressure
over
time to the setting you prefer – or as instructed by your dental professional.
Recommended Technique
For best results, start with the back teeth and work toward the front teeth. Direct
the brush head so that the water osser nozzle is angled slightly toward the
gumline. Move the brush head along the gumline pausing briey between each tooth
to allow water to clean between teeth. Continue until you have cleaned the inside
and outside of both the upper and lower teeth. When nished, empty any liquid le
in the reservoir.
NOTE: If you used mouthwash or any other solution besides water, see “Using
Mouthwash and Other Solutions” section.
BRUSH + FLOSS
To Brush + Floss at the same time, place brush head in mouth. Press BRUSH button,
then press FLOSS button.

8
Brush
Floss
CARE AND MAINTENANCE
Brush
Floss
Speed
Sonic–Fusion 2.0
Brush
Travel and Hose-Free Brushing
Toothbrush can be disconnected from the Sonic-Fusion® 2.0 for travel or hose-free
brushing. Place the handle and desired brush head(s) in the provided case for
protection when traveling.
NOTE: To disconnect the toothbrush from the water hose, press the round button
on the back side of the power handle. See Product Description section.
Using Mouthwash and Other Solutions
Your Waterpik® Sonic-Fusion® 2.0 can be used to deliver mouthwash and
antibacterial solutions. Aer using any special solution, rinse unit to prevent clogging
by partially lling reservoir with warm water and running unit with brush head
pointed into sink.
CARE AND MAINTENANCE
Before cleaning, unplug from the electrical outlet.
After Each Use
1. Aer each use, when all functions are turned OFF, remove the brush head
from the handle and rinse brush head under running water.
2. Wipe the handle dry aer each use.
General Cleaning / Removing Hard Water Deposits
• Clean the product when necessary by using a so cloth and mild
non-abrasive cleanser.
• Hard water deposits may build up in your unit, depending on the mineral content
of your water. If le unattended, it can hinder performance. Cleaning internal
parts: add 2 tablespoons of white vinegar to a full reservoir of warm water.
Point the handle and brush head into sink. Turn Water Flosser ON and run until
reservoir is empty. Rinse by repeating with a full reservoir of clean warm water.
This process should be done every 1 to 3 months to ensure optimal performance.
Leakage
If leaking due to a damaged hose, replacement hoses can be purchased at
www.waterpik.com or contact Water Pik Inc. customer service for a self service
repair kit.

9
ENGLISH
Brush
Floss
Brush
Floss
Cut
Remove
Battery
Battery Removal
This product contains a rechargeable Lithium-Ion battery. The battery is not
replaceable. Please do not dispose of the unit in the household waste. Remove the
batteries per the instructions below and recycle at your local recycling center.
Note: This process is not reversible.
Remove the battery only at the end of the product’s life for recycling. Doing so
earlier will destroy the product. Deplete the battery charge until the brush no longer
operates. Observe basic safety precautions to protect your eyes, hands, ngers, and
work surface. Remove the battery as shown and recycle them and the rest of the
product according to local regulations.
1. Run down the battery by operating the brush button until the motor
does not run.
2. Obtain a towel or cloth, hammer, at-head screwdriver, and wire cutters.
3. Remove and discard the brush head.
4. Cover the handle entirely with the towel or cloth.
5. Clamp the top of the handle against your work surface with one hand and
strike the handle housing around the bottom perimeter on all sides to release
the end cap latch. Continue striking and rotating the handle until the end
cap releases.
6. Remove the internal components by turning the handle upside down and while
holding on to the handle housing, press the sha down rmly on a hard surface.
7. The internal components should slide out when the handle is positioned
upside-down. If this does not occur, repeat steps 5 and 6 until the
components release.
8. Remove the end cap from the internal assembly.
9. Slide the battery out of the internal assembly.
10. Cut the battery wires one at a time with the wire cutters.
11. Recycle and dispose of the battery properly.
12. The remaining product pieces should be discarded appropriately.


10
LIMITED THREE YEAR WARRANTY
Service Maintenance
Waterpik® Sonic-Fusion® 2.0 have no consumer-serviceable electrical items
and do not require routine service maintenance. For all accessories go to
www.waterpik.com. You may also call our toll-free customer service number at
1-800-525-2774. Refer to the serial and model numbers in all correspondence.
These numbers are located on the bottom of your unit.
Still have questions? Go to www.waterpik.com.
Water Pik, Inc. warrants to the original consumer of this product that it is free
from defects in materials and workmanship for 3 years from the date of purchase.
Consumer will be required to submit the original purchase receipt as
proof of purchase date and if requested, the entire product, to support a
warranty claim. Water Pik, Inc. will replace, at its discretion, the product which in
its opinion is defective, provided the product has not been abused, misused, altered
or damaged aer purchase, was used according to instructions, and was used
only with accessories or consumable parts approved by Water Pik, Inc. This limited
warranty excludes accessories or consumable parts such as tips and brush heads.
This warranty gives you specic legal rights. You may also have other rights that
vary, depending on the law in your place of residence.
WATER PIK DISCLAIMS ALL OTHER EXPRESS OR IMPLIED WARRANTIES TO THE
EXTENT PERMITTEDBY LAWINCLUDING, BUT NOT LIMITEDTO,ALL WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. ALL IMPLIED
WARRANTIES ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY.
SOME STATES OR PROVINCES MAY NOT ALLOW LIMITATIONS ON HOW LONG AN
IMPLIED WARRANTY LASTS, SO THE ABOVE MAY NOT APPLY TO YOU.

11
ENGLISH
For USA Only
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Warning: changes or modications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Limitation of Liability
This limited warranty is your sole remedy against Water Pik and it shall not be
liable for any damages, whether direct, indirect, incidental, special, consequential,
exemplary or otherwise, including but not limited to property damage, arising out of
any theory of recovery, including statutory, contract or tort.

12
Arbitration
BINDING ARBITRATION AND WAIVER OF RIGHT TO ASSERT MATTERS IN COURT
AND RIGHT TO JURY TRIAL.
By purchasing, installing, or using this product you agree that any controversy or
claim arising out of or relating to your purchase, use, modication, installation,
or removal of this product shall be settled by binding arbitration. The arbitrator’s
decision will be nal and binding. Judgment on the award rendered by the arbitrator
may be entered in any court having jurisdiction over the matter. Further, you agree
that you will not have the right to litigate any claim arising out of or in relation to
your purchase, use, modication, installation, or removal of this product in any court
or to have a jury trial on that claim.
Arbitration of any matters shall be administered by the American Arbitration
Association and conducted by one arbitrator in accordance with the consumer
arbitration rules of the American Arbitration Association in eect at the time of
ling of the demand. The venue for all such arbitrations shall be Colorado and any
such arbitration shall be subject to the Federal Arbitration Act and Colorado law.
WAIVER OF RIGHT TO PARTICIPATE IN CLASS ACTIONS OR PURSUE CLAIMS IN A
REPRESENTATIVE CAPACITY.
Further, by purchasing, installing, or using this product you agree that arbitration
must be on an individual basis. This means neither you, nor we, may join or
consolidate claims inarbitration by or against other purchasers or users of water pik
products or the general public. Additionally, you may not litigate in court or arbitrate
any claims as a representative or member of a class or in a purported representative
capacity on behalf of the general public, other purchasers or users of this product,
other persons or entities similarly situated, or in a private attorney general capacity.
For Canada Only
This device complies with Innovation, Science and Economic Development Canada
(ISED)’s license-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and (2) This device must accept any
interference, including interference that may cause undesired operation of the
device.

Water Pik, Inc.,a subsidiary of
Church & Dwight Co., Inc.
1730 East Prospect Road
Fort Collins, CO 80553-0001 USA
1-800-525-2774
www.waterpik.com
Made in China. Designed and tested in the U.S.A.
Fabriqué en Chine. Conçu et testé aux É.-U.
Hecho en China. Diseñado y probado en los Estados Unidos.
Form No. 20028977-F AB
©2021 Water Pik, Inc.