WE-EF KTY234 LED User manual

Surge Protection
For comprehensive protection of a luminaire installation against lightning and
electrical surges, it is essential to cover mains supply and data input lines at
the distribution board level, by using respective primary (Type 1) and
secondary (Type 2) surge arrestors in compliance with EN61643-11/
IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and activated
prior to luminaire installation. Also, disconnect luminaires before operating
high-power devices such as, for example, electrical arc welders.
Do not open during installation
This product is factory-sealed.
Refer to the instructions contained in this
document for details.
Installation tools
Mounting hardware used on this product
includes fasteners with hexalobular socket
heads (ISO 10664). Installation requires the
use of matching tools.
Bollard
WE-EF LIGHTING
Installation and Maintenance
Instructions
INSTALLER
HOTLINE
[phone]
7am – 7pm AEST
KTX234 LED
KTY234 LED
ZFY23 0 LED
CFY259 LED

1
kg
300-0461 3.2
ESV4
1000
ø 180
600
ø 180
H kg
600 7.8
1000 8.9
IP66, Class I (Class II, III available on request), ta = 25°C
H = 600 mm
ZFY230
Bollard
H = 1000 mm
ZFY230
for ZFY230
for ZFY230
Weight
ESV4 for ZFY230
Planted root
– Galvanised steel.
Accessories:

2
ESV4
kgH
600 6.8
1000 8.9
kg
300-0461 3.2
Bollard
270
ø 180
KTX234
H = 270 mm
for KTX234 270 4.5
Weight
IP66, Class I (Class II, III available on request), ta = 25°C
H = 600 mm
KTY234
H = 1000 mm
KTY234
for KTY234
for KTY234
ESV4 for KTY234
Planted root – Galvanised steel.
Accessories:

3
685
ø 240
ø 240
1085
65°
ø 190 ø 240
ESV4
Weight kgH
for CFY259 600 15
for CFY259 1000 18
kg
Accessories:
Planted root – Galvanised steel.
ESV4 for CFY259 300-04644.4
Bollard
CFY259
H = 685 mm
CFY259
H = 1085 mm
CFY259
H600 / 6 LED
CFY259
H1000 / 2x6 LED
WARNING : HEAVY ITEMS
Ensure correct handling
techniques are used
IP66, Class I, (Class II, III available on request) ta = 25°C

4
rotate anti-clockwise until it can be lifted up.
To remove the head of the luminaire during maintenance, loosen screw X with a Torx T-20 tool and
Do not use high-pressure cleaners.
Apart from cleaning the product’s exterior surfaces, no special maintenance work is required.
Maintenance
LED
Light Source

In case of component failure due to abnormal circumstances or at end of life, replacement must be carried out
E\DVXLWDEO\TXDOLƂHGDQGWUDLQHGSURIHVVLRQDO
Warning: Do not open the luminaire or remove the bollard head while mains supply is switched on.
The luminaire head unit Bis factory sealed, warranty will be void if opened without authorisation from WE-EF
Lighting or nominated agent.
X
X
'Rear' of
Bollard
'Front' of
Bollard
X
X
ZFY230/CFY259 Head
KTY234 Head
5
X
To remove head To insert head
u
j
k
l
v
into the body and v rotate clockwise. When seated, wsecure the head by tightening screw X.
bollard body. To re-attach the head, align it to the bollard post as shown below, u drop the head
jRelease the grub screw X and k twist the head counter-clockwise, then l lift the head off the
Head Removal
bollard with the WE-EF logo at the front of the bollard.
For ZFY230/CFY250, The bollard post should be mounted that the grub screw X is the back of the
is secure by ensuring head cannot be rotated once grub screw secure.
For KTY234, ensure that the slim shield on the LED head lines up to the grub screw X. Confirm head
w
To remove head To insert head

Installation
The product must be installed and maintained by a
VXLWDEO\TXDOLƂHGSURIHVVLRQDOLQFRPSOLDQFHZLWKODWHVW
building/construction and/or electrical regulations and
relevant legislation.
Warning: Switch off and isolate the mains electrical
supply prior to installing and connecting the luminaire.
Notice:,IWKHOXPLQDLUHLVPRGLƂHGE\DQ\ERG\RWKHU
than the original manufacturer, then the warranty will
no longer be valid and shall become the full respon-
sibility of the modifying person/organisation. Claims
based on defects attributable to improper installation
and/or application, and the consequences thereof, are
excluded.
If the supplied cable of the KTX luminaire is damaged,
it must be replaced by WE-EF or a WE-EF authorized
agent.
head retention screw X.
secure by tightening screws D (not KTX) and the
Return head of luminaire B to bollard post C and 8)
= 1-10V control line).
Earthing, DA/DA = DALI control line, D-/D+
1-10V/DALI (L = Phase, N = Neutral, = b)
Earthing)
ON/OFF (L = Phase, N = Neutral, = a)
the terminal block:
Wiring is as follows and should match the labels on 7)
junction box J (not supplied) as per Fig. 3.
and must be connected via a compliant IP67
clamp H. Note : The KTX does not have the gear tray
the underside of the head B, and is secured by the
supply terminal block located on the gear tray G on
As per Fig. 2 Connect luminaire cable I to mains 6)
the head retention screw X is positioned.
on KTX). Note that the rear of the bollard is where
the base with retention bolts D (base is integrated
and tightening bolts G and the post C is attached to
Set cast base F in position and secure by inserting 5)
(see previous page).
rotating it anti-clockwise until it can be lifted up
after loosening screw X with a Torx T-20 tool and
Remove head of luminaire B from bollard post C 4)
mains cable length are provided.
(QVXUHWKDWDVROLGIRXQGDWLRQDVZHOODVVXIƂFLHQW
A suitable recess to be provided for planted root A. 3)
conforms with mains electrical supply.
Checkthat rating shown on luminaire label2)
Switch off and isolate the mains electrical supply.1)
maximum stability.
incorporate the optional planted root to ensure
to an even surface, however it is recommended to
The luminaire is suitable for installation directly on
Installation Procedure
) DC (+ = Positive, - = Negative)c
6

Torque:
Screw Torque
M4 max. 2.0 Nm
M5 max. 4.0 Nm
M6 max. 6.0 Nm
M8 max. 15.0 Nm
M16 max.100.0 Nm
C
B
D
F
E
A
Fig. 1
J
H
G
Fig. 2
Fig. 3
I
7

www.we-ef.com
WE-EF LEUCHTEN
Germany
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LUMIERE
France
Tel [phone]
Fax [phone]
[e-mail]
WE-EF HELVETICA
Switzerland
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United Kingdom
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
Thailand
Tel [phone]
Fax [phone]
LQIRDVLDSDFLƂF#ZHHIFRP
WE-EF LIGHTING
Australia
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[e-mail]
INSTALLER
HOTLINE
[phone]
7am – 7pm AEST
subject to change.
7HFKQLFDOVSHFLƂFDWLRQVDUH
© WE-EF 2020
TO9235W0218 Rev2 271020