WE-EF PSY414 User manual

WE-EF LIGHTING
Installation and Maintenance
Instructions
Bollard
PSY414 LED
PSY424 LED
PTY414 LED
PTY424 LED
Surge Protection
This product features built-in surge protection circuitry in compliance
with applicable standards.
For comprehensive protection of a luminaire installation against lightning
and electrical surges,it is essential to cover mains supply and data input
lines at the distribution board level,by using respective primary (Type 1)
and secondary (Type 2) surge arrestors in compliance with EN61643-11/
IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and
activated prior to luminaire installation.Also,disconnect luminaires
before operating high-power devices such as, for example,electrical
arc welders.
Do not open during installation
This product is factory-sealed.
Refer to the instructions contained
in this document for details.
Installation tools
Mounting hardware used on this product
includes fasteners with hexalobular
socket heads (ISO 10664).Installation
requires the use of matching tools.

1
IP66/IP67, IK10,Class I, ta = 40°C
Weight lb
for PSY414 29.3
for PSY424 35.5
for PTY414 30.9
for PTY424 41.9
Accessories:
Planted root – Galvanised steel. lb
ESV2 for PSY414/424 300-9115 8.4
ESV2
Bollard
PSY414
PSY424
PTY414
PTY424

2
Light Source
LED
Maintenance
Apart from cleaning the product’s exterior surfaces,no special maintenance work is required.
Do not use high-pressure cleaners.
In case of component failure due to abnormal circumstances or at end of life, replacement must be carried
RXWE\DVXLWDEO\TXDOLĥHGDQGWUDLQHGSURIHVVLRQDO
Warning: Do not open luminaire while mains supply is switched on.

3
Installation
The product must be installed and maintained by a VXLWDEO\TXDOLĥHGSURIHVVLRQDOLQFRPSOLDQFHZLWKODWHVW
building/construction and/or electrical regulations and relevant legislation.
Warning:6ZLWFKRĪPDLQVHOHFWULFDOVXSSO\SULRUWRLQVWDOOLQJDQGFRQQHFWLQJWKHOXPLQDLUH
Notice:,IWKHOXPLQDLUHLVPRGLĥHGE\DQ\ERG\RWKHUWKDQWKHRULJLQDOPDQXIDFWXUHUWKHQWKHZDUUDQW\ZLOO
no longer be valid and shall become the full responsibility of the modifying person/organisation.
Claims based on defects attributable to improper installation and/or application, and the consequences
thereof, are excluded.
Attention: The luminaire is factory-sealed and does not need to be opened during installation.
The installation on site must comply with local and/or national health and safety regulations.

4
Installation Procedure
It is recommended to incorporate the optional planted root to ensure maximum stability.
 6ZLWFKRĪPDLQVHOHFWULFDOVXSSO\
4) Remove terminal box cover Cas shown.
2) Remove sleeve Afrom post B.
C
 3XOOFDEOHWKURXJKFHQWUHKROHDQGIDVWHQĦDQJH
plate Ewith provided fasteners to ground.
Ensure proper orientation of terminal box. An
optional planted root is available.
E
Note: Planted root installation instruction is
available in additional document.

5
6) Pull cable D(and second cable for through
wiring, if required) through strain relief(s) Fand
terminate in terminal block G.Lock cable(s) with
strain relief(s).
7) Return terminal box cover C.
C
5) Check that rating shown on luminaire label
conforms with mains electrical supply.
(example)
PSY424 120-277 / 60Hz
114-XXXX SOE XXXXXXX
LED 4000K 18W item no.XXX
08/18 IP66
8) Place sleeve Aover post Bwith sticker I
pointing up as shown.
I
A
B
G
F
D

6
10)Remove countersunk screws Jfrom head K
with Torx 25 tool (supplied by WE-EF).
9) Align sleeve ALQWRĦDQJHSODWHE
(good and bad engagement).
E
A
K
J
12)Place head Kover sleeve Aand check for
alignment.
ĦXVK
A
K
11)Hold head Kunder arm. Grab socket L,
connect and tighten with plug M.
K
M
L

7
N
-
13)Tighten recessed screws Ngradually in alter-
nating sequence 6 Nm (53.1 in-lb) with Torx
30 tool (supplied by WE-EF).
14)Return countersunk screws Jinto head and
tighten.

www.we-ef.com
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[email protected]
TO9245W0422 © WE-EF 2022
Technical specifications are
subject to change.

WE-EF LIGHTING
Installation and Maintenance
Instructions
Planted Root
ESV4
ESV2
ESV6

2
Planted Root
ESV4 300-0461
ESV4 300-0586
ESV4 300-0464
ESV4 300-0459
Suitability
1. KTX234
2. KTY234
3. ZFY230
4. GRY224
5. Short post
Suitability
1. XRY334
2. XRZ334
3. RRY334
4. RRZ334
Suitability
1. CFY259
2. GRY234
3. RRY324
4. RRZ324
5.XRY324
6.XRZ324
Suitability
1. QSI254

3
Planted Root
ESV2 300-9115
ESV6 300-0824
ESV6 300-0457
Suitability
1. PSY414/424
Suitability
1.AML-C
2. FLA461
Suitability
1. LTM440
2. LTM444
3.AMW-C
4.AMF-C
5.AMF-S
6.AML-C

4
Installation Instruction
1) Note: It is the responsibility to installer to
ensure the suitability of the ESV planted root
for any local or national structural requirements
for installation,and that planted root is suitable
IRUVLWHVSHFLĥFFRQGLWLRQV
Instructions are a guideline for installation to
these requirements and provide detail for
installation orientation and mounting details.
4) For ESV2 please orientate planted root as
shown (base plate is parallel to the pathway).
For this installation, use M12 bolts supplied.
2) Please note, ESV4 and ESV6 must be
RULHQWDWHGFRUUHFWO\IRUGLĪHUHQWSURGXFWV
In both instances conduit entry can be rotated
to match cable routing.
When the ESV is being installed for following
products: KTY234/KTX234/ZFY230/CFY259/
FLA461,please orientate the planted root
as shown (base plate is at an angle of 45°
to the pathway).For this installation,
use the M8 bolts supplied.
3) For all other product that use ESV4 please
orientate planted root as shown (base plate is
parallel to the pathway).For this installation,
use M8 bolts supplied.

5
 2ULHQWDWH(69DVUHTXLUHGDQGĥWHOHFWULFDO
connections/conduit.
5) For all other product that use ESV6 please
orientate planted root as shown (base plate
is parallel to the pathway).For this installation,
use M16 bolts supplie.
7) Place the ESV in the form work for concrete
pad, ensuring orientation, position and levels
are correct. Ensure all openings on ESV are
EODQNHGRĪLQFOXGLQJPRXQWLQJSODWHKROH
8) Fit the nominated bolts through mounting
ĦDQJH(QVXUHVHYHUDOWKUHDGVIHHGWKURXJK
 WKHSODWHDQGWDSHRĪWRSDQGERWWRP%ROWV
DUHLQVHUWHGWRSURWHFWWKUHDGVRĪSODWHDQG
QHHGWREHUHPRYHGIRUĥWWLQJLQVWDOODWLRQ
after setting the ESV.

6
9) Pour concrete to desired level depending on
requirement of concrete,paver or soil. Ensure
WKDWIRUDQ\LQVWDOODWLRQPRXQWLQJĦDQJHPXVW
EHĦXVKRUKLJKHUWKDQVXUURXQGLQJVXUIDFH
level.
$IWHUFRQFUHWHKDVFXUHGIRUVSHFLĥHGWLPH
UHPRYHEODQNLQJDQGEROWV,QVWDOOĥWWLQJ
(as per luminaire instructions) onto mounting
ĦDQJH
Concrete
Paver
Soil

www.we-ef.com
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[email protected]
TO9257W0422 © WE-EF 2022
Technical specifications are
subject to change.