WE-EF VLR110 LED User manual

Surge Protection
This product features built-in surge protection circuitry in compliance with
applicable standards.
For comprehensive protection of a luminaire installation against lightning and
electrical surges, it is essential to cover mains supply and data input lines at
the distribution board level, by using respective primary (Type 1) and secondary
(Type 2) surge arrestors in compliance with EN61643-11/IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and activated
prior to luminaire installation. Also, disconnect luminaires before operating
high-power devices such as, for example, electrical arc welders.
Do not open during installation
This product is factory-sealed.
Refer to the instructions contained in this
document for details.
WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Linear Wallwasher
VLR110 LED
VLR120 LED
VLR130 LED
VLR140 LED
VLR150 LED

2
48
180°
B
C
Linear Wallwasher
VLR100
VLR100 [LA10]
IP66, IK08. Class I.
B
C
48
180°
Product Dimensions and Weight:
L A B C kg
VLR110 328 287 88 132 1.7
VLR120 628 587 88 132 2.9
VLR130 928 887 88 132 3.8
VLR140 1228 1187 88 132 4.7
VLR150 1528 1487 88 132 5.6
VLR120 [LA10] 628 578 424 468 3.5
VLR130 [LA10] 928 878 424 468 4.4
VLR140 [LA10] 1228 1178 424 468 5.2
ø 7.5 mm
1 mm2
Tool required
– Screwdriver 5 mm

3
Light Source
LED
Maintenance
Apart from cleaning the product’s exterior surfaces, no special maintenance work is required.
Do not use high-pressure cleaners.
In case of component failure due to abnormal circumstances or at end of life, replacement must be carried out
E\DVXLWDEO\TXDOLƂHGDQGWUDLQHGSURIHVVLRQDO
Warning: Do not open luminaire while mains supply is switched on.
Note: Do not place luminaire nor brackets in water. When luminaire should be mounted on the ground,
use sealable junction box (not included, available by WE-EF).

4
Installation
The product must be installed and maintained by a VXLWDEO\TXDOLƂHGSURIHVVLRQDOLQFRPSOLDQFHZLWKODWHVW
building/construction and/or electrical regulations and relevant legislation.
Warning: Switch off mains electrical supply prior to installing and connecting the luminaire.
Notice:,IWKHOXPLQDLUHLVPRGLƂHGE\DQ\ERG\RWKHUWKDQWKHRULJLQDOPDQXIDFWXUHUWKHQWKHZDUUDQW\ZLOOQR
longer be valid and shall become the full responsibility of the modifying person/organisation. Claims based on
defects attributable to improper installation and/or application, and the consequences thereof, are excluded.
Attention: The luminaire is factory-sealed and does not need to be opened during installation.
The installation on site must comply with local and/or national health and safety regulations.

5
InstallationProcedure
Luminaire is factory sealed and does not need to be opened during installation.
1) Switchoffthemainselectricalsupply.
 'HWHUPLQHSRVLWLRQRIWKHƂ[LQJVFUHZVD(notsupplybyWE-EF).
&KHFNSURGXFWGLPHQVLRQSDJHDERXWWKHGLVWDQFHRIWKHGULOOLQJKROHV'ULOOFRUUHVSRQGLQJƂ[LQJKROHVDQG
insertdowelEQRWVXSSO\E\:(()FKRRVHVXLWDEOHƂ[LQJPDWHULDO
Attention:Makesurenottodamageanyelectricalcable,waterpipesorotherdevices.
3) InstallwallbracketBtoluminaireA DQGƂ[LWDSSO\LQJ1PRISUHVVXUHE\XVHRIWKHVFUHZVG.
4) InstalltheluminaireAtothedeterminedpositionbyuseofthescrewsD.
5) ConnectleadsofcableCtomainsupplyviasuitableconnectorofcustomer’schoice(L=Phase,N=Neutral,
=Earthing,DA/DA=DALIcontrolline).
6) AftertheluminaireAisconnected,thebracketcangetadjustedbylooseningandrespectivelytightening
screwsG.
 5HPRYHƂOPIURPWKHOHQVEHIRUHXVH