WE-EF XRY324 LED User manual

WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Bollard
XRY324 LED
XRY334 LED
RRY324 LED
RRY334 LED
XRZ324 LED
XRZ334 LED
RRZ324 LED
RRZ334 LED
GRY224 LED
GRY234 LED
Surge Protection
This product features built-in surge protection circuitry in compliance with
applicable standards.
For comprehensive protection of a luminaire installation against lightning and
electrical surges, it is essential to cover mains supply and data input lines at
the distribution board level, by using respective primary (Type 1) and secondary
(Type 2) surge arrestors in compliance with EN61643-11/IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and activated
prior to luminaire installation. Also, disconnect luminaires before operating
high-power devices such as, for example, electrical arc welders.

1
IP55*, IP66**, IK10, Class I, ta = 40°C
Bollard
XRY324**
XRY334** RRY324** RRY334** GRY224** GRY234**
RRZ324*
RRZ334*
XRZ324*
XRZ334*

2
Light Source
LED
Maintenance
Apart from cleaning the product’s exterior surfaces, no special maintenance work is required.
Do not use high-pressure cleaners.
In case of component failure due to abnormal circumstances or at end of life, replacement must be carried out
by a suitably qualiƂ ed and trained professional.
Warning: Do not open luminaire while mains supply is switched on.
Product Dimensions:
A B C D
GRY224 ø 160 700 ø 130 ø 160
GRY234 ø 250 1000 ø 202 ø 230
XRY324 ø 180 700 ø 202 ø 230
XRY334 ø 270 1000 ø 286 ø 320
XRZ324 ø 180 900 ø 202 ø 230
XRZ334 ø 270 1100 ø 286 ø 320
RRY324 ø 205 900 ø 202 ø 230
RRY334 ø 320 1000 ø 286 ø 320
RRZ324 ø 205 900 ø 202 ø 230
RRZ334 ø 320 1100 ø 286 ø 320
ESV4
Accessories:
Planted root – Galvanised steel. kg
ESV4 for GRY224 300-0461 4.4
ESV4 for GRY234 300-0464 6.0
ESV4 for XRY324/XRZ324/RRY324/RRZ324 300-0464 6.0
ESV4 for XRY334/XRZ334/RRY334/RRZ334 300-0586 7.2

3
Installation
The product must be installed and maintained by a
suitably qualiƂ ed professional in compliance with latest
building/construction and/or electrical regulations and
relevant legislation.
Warning: Switch off mains electrical supply prior to
installing and connecting the luminaire.
Notice: If the luminaire is modiƂ ed by anybody other
than the original manufacturer, then the warranty will
no longer be valid and shall become the full respon-
sibility of the modifying person/organisation. Claims
based on defects attributable to improper installation
and/or application, and the consequences thereof, are
excluded.

4
1) Switch off mains electrical supply.
Installation Procedure
It is recommended to incorporate the optional planted root to ensure maximum stability.
4) Remove cover B from cast base C by loosening
countersunk screws D.
2) Check that rating shown on luminaire label
conforms with mains electrical supply.
(example)
XRZ334 220-240V/50Hz, 1-10v
114-9632 SOE XXXXXXX
LED 4000K 12W item no. XXX
05/17 IP55
3) A suitable recess to be provided for planted
root A. Ensure that a solid foundation as well
as sufƂ cient mains cable length are provided.
Note: Planted root installation instruction is
available at the end of this document.

5
CIRCUIT ON/OFF 1-10 V DALI
L PHASE PHASE PHASE
N NEUTRAL NEUTRAL NEUTRAL
EARTH EARTH EARTH
D+/DA --- +/–10V DALI
D–/DA --- +/–10V DALI
5) Connect luminaire cable E to mains supply
cable F in watertight terminal connector G
(not supplied by WE-EF).
8) Reposition cover B and secure by tightening
screws D.
6) Place watertight terminal connector G and
excess cable inside post H.
7) Set luminaire in position and secure by
inserting and tightening bolts I.

www.we-ef.com
WE-EF LEUCHTEN
Germany
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LUMIERE
France
Tel [phone]
Fax [phone]
[e-mail]
WE-EF HELVETICA
Switzerland
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
Thailand
Tel [phone]
Fax [phone]
info.asiapaciƂ [e-mail]
WE-EF LIGHTING
Australia
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[e-mail]
TO9233W0219 © WE-EF 2019
Technical speciƂ cations are
subject to change.

WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Planted Root
ESV4
ESV2
ESV6

2
Planted Root
ESV4 300-0461
ESV4 300-0586
ESV4 300-0464
ESV4 300-0459
Suitability
1. KTX234
2. KTY234
3. ZFY230
4. GRY224
5. Short post
Suitability
1. XRY334
2. XRZ334
3. RRY334
4. RRZ334
Suitability
1. CFY259
2. GRY234
3. RRY324
4. RRZ324
5. XRY324
6. XRZ324
Suitability
1. QSI254

3
Planted Root
ESV2 300-9115
ESV6 300-0824
ESV6 300-0457
Suitability
1. PSY414/424
Suitability
1. AML-C
2. FLA461
Suitability
1. LTM440
2. LTM444
3. AMW-C
4. AMF-C
5. AMF-S
6. AML-C
240
200
600

4
Installation Instruction
1) Note: It is the responsibility to installer to
ensure the suitability of the ESV planted root
for any local or national structural requirements
for installation, and that planted root is suitable
IRUVLWHVSHFLƂFFRQGLWLRQV
Instructions are a guideline for installation to
these requirements and provide detail for
installation orientation and mounting details.
4) For ESV2 please orientate planted root as
shown (base plate is parallel to the pathway).
For this installation, use 30 mm long M12
bolts supplied.
2) Please note, ESV4 and ESV6 must be
orientated correctly for different products.
In both instances conduit entry can be rotated
to match cable routing.
When the ESV is being installed for following
products: KTY234/KTX234/ZFY230/CFY259/
FLA461, please orientate the planted root
as shown (base plate is at an angle of 45°
to the pathway). For this installation,
use the 40 mm long M8 bolts supplied.
3) For all other product that use ESV4 please
orientate planted root as shown (base plate is
parallel to the pathway). For this installation,
use 25 mm long M8 bolts supplied.

5
 2ULHQWDWH(69DVUHTXLUHGDQGƂWHOHFWULFDO
connections/conduit.
5) For all other product that use ESV6 please
orientate planted root as shown (base plate
is parallel to the pathway). For this installation,
use 40 mm long M16 bolts supplie.
7) Place the ESV in the form work for concrete
pad, ensuring orientation, position and levels
are correct. Ensure all openings on ESV are
blanked off, including mounting plate hole.
8) Fit the nominated bolts through mounting
ƃDQJH(QVXUHVHYHUDOWKUHDGVIHHGWKURXJK
the plate and tape off top and bottom. Bolts are
inserted to protect threads off plate and need to
EHUHPRYHGIRUƂWWLQJLQVWDOODWLRQDIWHUVHWWLQJ
the ESV.

6
9) Pour concrete to desired level depending on
requirement of soil, paver or concrete. Ensure
WKDWIRUDQ\LQVWDOODWLRQPRXQWLQJƃDQJHPXVWEH
ƃXVKRUKLJKHUWKDQVXUURXQGLQJVXUIDFHOHYHO
$IWHUFRQFUHWHKDVFXUHGIRUVSHFLƂHGWLPH
UHPRYHEODQNLQJDQGEROWV,QVWDOOƂWWLQJ
(as per luminaire instructions) onto mounting
ƃDQJH
Concrete
Paver
Soil

www.we-ef.com
WE-EF LEUCHTEN
Germany
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LUMIERE
France
Tel [phone]
Fax [phone]
[e-mail]
WE-EF HELVETICA
Switzerland
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
Thailand
Tel [phone]
Fax [phone]
LQIRDVLDSDFLƂF#ZHHIFRP
WE-EF LIGHTING
Australia
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[e-mail]
TO9257W0420 © WE-EF 2020
7HFKQLFDOVSHFLƂFDWLRQVDUH
subject to change.