WE-EF ASP530 LED User manual

Surge Protection
This product features built-in surge protection circuitry in compliance
with applicable standards.
For comprehensive protection of a luminaire installation against lightning
and electrical surges,it is essential to cover mains supply and data input
lines at the distribution board level,by using respective primary (Type 1)
and secondary (Type 2) surge arrestors in compliance with EN61643-11/
IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and
activated prior to luminaire installation.Also,disconnect luminaires
before operating high-power devices such as, for example,electrical
arc welders.
Do not open during installation
This product is factory-sealed.
Refer to the instructions contained
in this document for details.
WE-EF LIGHTING
Installation and Maintenance
Instructions
Post Top Luminaire
ASP530 LED

1
,3&ODVV,WDţũ&
ASP530
Post Top Luminaire

2
Light Source
LED
Maintenance
Apart from cleaning the product’s exterior surfaces,no special maintenance work is required.
Do not use high-pressure cleaners.
In case of component failure due to abnormal circumstances or at end of life, replacement must be carried
RXWE\DVXLWDEO\TXDOLĥHGDQGWUDLQHGSURIHVVLRQDO
Warning: Do not open luminaire while mains supply is switched on.

3
Installation
The product must be installed and maintained by a
VXLWDEO\TXDOLĥHGSURIHVVLRQDOLQFRPSOLDQFH
with latest building/construction and/or electrical
regulations and relevant legislation.
Warning:6ZLWFKRĪPDLQVHOHFWULFDOVXSSO\SULRUWR
installing and connecting the luminaire.
Notice:,IWKHOXPLQDLUHLVPRGLĥHGE\DQ\ERG\RWKHU
than the original manufacturer,then the warranty
will no longer be valid and shall become the full
responsibility of the modifying person/organisation.
Claims based on defects attributable to improper in-
stallation and/or application,and the consequences
thereof, are excluded.
Installation Procedure
6ZLWFKRĪPDLQVHOHFWULFDOVXSSO\
2) Check that rating shown on luminaire label
conforms with mains electrical supply.
3) Loosen pressure screw Rand packing ring G.
Place pressure screw Rand packing ring G
around mains cable C.
3XVKDWOHDVWLQRIPDLQVFDEOHCthrough
spigot P. Reposition packing ring Gand tighten
pressure screw Rto secure mains cable C.
5) Loosen locking screws Sto allow insertion of
spigot Pinto spigot holder H. Keep support
screw Ttightened.
6) Align and lock support screw Tusing spigot P
keyway.
7) Push luminaire up until spigot Pis fully
recessed into spigot holder H.Rotate luminaire
counter-clockwise and allow it to rest on
locating support screw T.
8) Tighten locking screws S, to lock luminaire in
position.
9) Open luminaire by loosening screws L.
Carefully unhook lanyard I.
/RRVHQVFUHZV-GRQRWWXUQRXW5RWDWHJHDU
tray Mcounter-clockwise and pull out gently.
11) Connect mains cable Cto terminal connecto
K.
12) Return gear tray Mto its original position and
tighten screws J.
13) Reconnect lanyard I and close luminaire by
tightening screws L.

4

5

www.we-ef.com
WE-EF LIGHTING
United States of America
7HO
)D[
[email protected]
72:Ŏ:(()
Technical specifications are
subject to change.