Welch Allyn SureTemp 679 Instruction Manual

SureTemp Thermometer
Model 679
OperatingOperating
OperatingOperating
Operating
InstructionInstruction
InstructionInstruction
Instruction
ManualManual
ManualManual
Manual
0050

Thank you for purchasing the Welch Allyn Model 679 SureTemp®
thermometer. The operating and maintenance instructions found in
thismanualshouldbefollowedtoensureyearsofaccurateandreliable
service. Please read these instructions thoroughly before using your
679 SureTemp®thermometer.
TechnicalservicemanualsmaybeorderedbycontactingWelchAllyn
Customer Service at [phone].
© 1997 by Welch Allyn, Inc. All rights reserved. No part of this manual may be reproduced or transmitted in any form
or by any means, electronic or mechanical, including photocopy, without prior consent in writing from Welch Allyn.
Printed in the U.S.A.
U.S. patent 5,632,555. Additional U.S. and foreign patents pending.
TheCE mark on thisproduct indicates it hasbeen tested to andconforms with the provisions
noted within the 93/42/EEC Medical Device Directive.
European Regulatory Manager, Medical Division
Welch Allyn Ltd., Navan, Co. Meath
Republic of Ireland

CONTENTS
INTRODUCTION .................................................................. 2
SAFETY&WARNINGS ......................................................... 2
PARTS ................................................................................ 3
MOUNTINGINSTRUCTIONS ................................................. 4
SETUP ............................................................................... 4
CHANGING PROBES ..................................................................5
FEATURES.......................................................................... 5
DISPLAYINDICATORS .......................................................... 6
OPERATION ........................................................................ 8
TAKING ORALTEMPERATURES ..................................................... 8
USING MONITOR MODE ................................................................9
TAKINGAXILLARYTEMPERATURES (Under 4 years)................. 10
TAKINGAXILLARYTEMPERATURES (4 years -Adult) .................11
TAKING RECTALTEMPERATURES ............................................... 12
MAINTENANCE ................................................................. 12
CLEANINGANDSTERILIZATION ......................................... 13
SPECIFICATIONS ............................................................... 13
CUSTOMERSERVICE ......................................................... 13
LIMITEDWARRANTY ............................................. BackCover
1

INTRODUCTION
The Welch Allyn 679 SureTemp is a portable thermistor thermometer to
be used for measuring patient temperatures ranging from 84°F to 108°F
(28.9°C to 42.2°C). Oral/axillary and rectal probes utilize single-use
disposable probe covers which limit cross-contamination. Oral, axillary
and rectal temperatures can be taken using Normal or Monitor operating
modes. Axillary temperatures taken using the Normal operating mode
will display temperatures in about 10 seconds for patients 3 years and
under. Axillary temperatures for patients 4 years through adult are taken
using the Monitor operating mode and will display temperatures in about
5 minutes. In the Normal mode, the thermometer’s microprocessor
“predicts”body temperature in about 4 seconds for oral temperatures and
in about 15 seconds for rectal temperatures. The Monitor mode continu-
ously displays the temperature of the probe which will reflect the
patient’s actual temperature in about 3 minutes and will continue for as
long as the probe remains in place.
SAFETY& WARNINGS
DO NOT USE IN THE PRESENCE OF FLAMMABLE
ANESTHETICS.
Caution: Federal (USA) law restricts this device to sale by or on the order of
a physician.
In order to obtain accurate and reliable temperature-taking results and ensure
patient safety, it is important that this booklet be read thoroughly prior to
using the instrument. If you have any technical or clinical questions concern-
ing the thermometer’s use and/or care, please contact our Customer Service
Department at [phone].
•Single-use disposable probe covers, available from Welch Allyn, will
limit patient cross-contamination. The use of any other probe cover or
the failure to use a probe cover may produce temperature errors and will
invalidate the instrument’s warranty.
•Oral probes (blue ejection button) are to be used for taking oral and
axillary temperatures only. Rectal probes (red ejection button) are to be
used for taking rectal temperatures only. The use of the wrong probe
will produce temperature errors.
•The thermometer case is not waterproof; do not drip fluids onto it.
•Do not use this instrument for any purpose other than that specified in
this booklet. Doing so will invalidate the instrument’s warranty.
2

3
•Do not use the thermometer if you notice any signs of damage to the
probe or instrument. Contact our Customer Service Department for
immediate assistance.
•Do not ETO sterilize without using proper procedures described in the
679 SureTemp technical manual.
Figure 1
1. Probe cover box 5. Probe handle
2. Display 6. Probe storage channel
3. Mode button 7. Latching probe connector
4. Probe cover ejection button 8. Battery door

4
WALL MOUNTING INSTRUCTIONS
The optional wall mount bracket should be mounted approximately 48 inches
fromthefloor. Thisallowstheenduserofaverageheightrelativelyeasy access
to the probe and probe covers. It should have at least 12 inches of clearance on
thetop of the unit so that the enduser can easily remove the thermometer probe
and load a probe cover without hindrance. Clearance of at least 4 inches from
the bottom of the unit and from either side is also advisable to prevent tangling
of the probe cord with other equipment at the bedside.
The wall mount bracket should be mounted in a location so that when a
thermometer is installed, the display can be read from the patient's bedside.
Placement should also ensure that the probe can be readily removed from
the thermometer, a probe cover can be easily installed and the probe can
be returned to its position without stress being placed on either the
instrument, the wall mount or most importantly, the patient.
SETUP
1. Install the supplied Oral/Axillary probe or optional Rectal probe by
inserting the latching plug on the end of the coiled cord into the plug
receptacle on the unit. The plug snaps into place and cannot be removed
without depressing the latch. (Figure 1).
Note: The Oral probe is also used to take Axillary measurements.
2. Observe the LCD to see that the probe
type OrL = Oral or rEC = Rectal is
displayed.
3. Insert probe shaft completely into probe
storage channel.
4. Remove the probe from the storage
channel.
5. Observe the LCD to see that all display
segmentsappearfollowedbythedisplay
of the probe type OrL = Oral or rEC =
Rectal and temperature scale (°C or °F).
Replace probe in storage channel.
6. Insert a box of disposable probe covers
(part number 05031) into the probe
cover storage well.

CHANGINGPROBES
•Depress the latch and unplug the probe connector from the thermometer.
•Remove the probe from the storage channel.
•Repeat steps 1 through 6 in the SETUP section.
FEATURES
•Normal Mode: The thermometer takes oral temperatures in about 4
seconds and rectal temperatures in about 15 seconds. Axillary tempera-
tures taken using the Normal operating mode will display temperatures in
about 10 seconds for patients under 4 years. The unit will always operate
in Normal mode unless the Mode button is depressed for more than 2
seconds after the initial temperature is displayed which changes it to
Monitor Mode. Replacing the probe in the storage channel automatically
resets the unit to Normal mode.
•MonitorMode: Monitormodeisgenerallyusedforlongterm(continuous)
temperature monitoring, taking adult axillary temperatures, or when diffi-
cult situations prevent accurate temperatures from being taken in the
Normal mode.
•Oral/Axillary Probe with 4’coiled cord and latching plug to prevent
unintentional plug removal.
•Optional Rectal Probe with 4’coiled cord and latching plug.
•Mode Button: Recalls the last Normal mode temperature taken, converts
temperatures from °F to °C, switches the unit to Monitor Mode and allows
the clinician to change the probe type from Oral to Axillary.
5

Mode Table
DISPLAYINDICATORS
Instrument Malfunction: This icon is displayed if the unit is not
functioning properly. Contact the Welch Allyn Customer Service
Department.
Broken Probe: If displayed, probe may be damaged. Remove and
reinstall probe. If error persists, then install a new probe.
ProbePosition: Probe hasbrokencontactwiththetissue. Onceproper
contacthasbeenachieved,theiconwillbeturnedoff but willreappear
at the end of the temperature measurement. It is recommended that a
new temperature be taken.
or Axillary Probe: This icon is displayed to show that the axillary
mode has been selected.
or Oral Probe: This icon is displayed to show that the oral mode has
been selected.
6

or Rectal Probe: This icon is displayed to show that the rectal mode
has been selected.
Walking Segments: This will be displayed when the thermometer is
in process of taking a temperature in the Normal mode.
Monitor Mode: Monitor mode is generally used for long term
temperature monitoring, taking axillary temperatures, or when
difficult situations prevent accurate temperatures from being taken
in the Normal mode.
High Temperature: This icon is displayed if the patient’s temperature
is greater than 108.0°F (42.2°C).
Low Temperature: This icon is displayed if the patient’s temperature
is less than 84.0°F (28.9°C).
High Ambient Temperature: This icon is displayed if the ambient
temperature is greater than 104°F (40°C).
Low Ambient Temperature: This icon is displayed if the ambient
temperature is less than 60.8°F (16.0°C).
Low Battery: This icon flashes when batteries are low and will
remain on when batteries are dead.
Display Test: All segments of the thermometer display will appear
briefly when the probe is removed from the storage channel to ensure
proper function.
7

OPERATION
1. Withdrawtheprobefromthestoragechan-
neland observeathermometerdisplay test
followed by an audible tone and a display
of the probe type OrL = Oral,
ALy=Axillary, or rEC = Rectal.
2. Load a probe cover onto the probe. Hold
probe handle collar with thumb and fore-
finger, being careful not to hold or press
the “ejection”button. Press the collar
down firmly to secure the cover.
TAKINGORALTEMPERATURES
BLUECAPPEDPROBE
The ability of the 679 SureTemp to take an
accurate oral temperature in about 4 seconds
requires correct user technique.
1. WithOrLshowingonthe display, insert the
probe tip gently into the patient’s slightly
opened mouth. Quickly slide the probe
underthe tongue oneithersideofthe mouth
to reach the sublingual pocket. Have the
patient close his/her lips around the probe.
2. Hold the probe in place, keeping the tip in
contact with tissue during the entire tem-
perature measurement process. Holding
the probe still will ensure a fast and
accurate measurement.
8
SUBLINGUAL POCKETS
98.0
98.4 98.2
98.298.4
98.0 98.0
97.297.4
96.8
96.8
98.2

9
3. Duringthetemperaturemeasurementcycle,
“walking”segments will appear on the
display indicating measurement is in pro-
cess.
4. When the final temperature has been
reached,atonewillsoundandthepatient’s
temperature will be displayed.
5. Afterthetemperaturemeasurementiscom-
plete,removetheprobefromthepatient,thenejecttheprobecoverbyfirmly
pressing the ejection button on the probe. (Figure 1)
6. Insert the probe into the storage channel to clear the display, in preparation
for another temperature.
USINGMONITORMODE
Remove the probe from the storage channel and take a temperature using Oral,
Rectal,orAxillaryMode. Afterthetemperatureisdisplayed,depresstheMode
button for more than 2 seconds. The “M”icon will appear on the LCD
indicatingtheunitisinMonitormode. Theunitisreadytocontinuouslydisplay
temperatures in Monitor mode. After the Monitor mode temperature has been
taken, replacing the probe in the storage channel clears the display and resets
thethermometertoNormalmode. TheunitwillautomaticallyentertheMonitor
mode by removing the probe from the probe storage channel and waiting 60
seconds.
NOTE: WhenusingtheMonitormode,allowthetemperaturereadout
tostabilizefor3minutesfororalandrectaltemperaturesand5minutes
for axillary temperatures.

10
TAKINGAXILLARYTEMPERATURES
(PATIENTS UNDER4YEARS)
BLUECAPPEDPROBE
Axillary temperature in children ages’birth through three years can be taken
with the SureTemp in the Axillary Mode, with an oral probe.
1. Withdraw the oral probe from its storage channel and observe a quick
thermometer self-test on the display.
2. With OrL probe type
displayed,depress and
hold the Mode button
for two seconds. ALy
will now appear in the
display,indicatingthat
the thermometer is
ready to take an axil-
lary temperature mea-
surement. Unless the
thermometer is in the
axillary mode,inaccurate axillary temperature readings will result.
Note: The thermometer may be placed in the Axillary mode as the default
modeusingtheBiotechmode,seetheTechnicalServiceManualforfurther
details. Whenthe default modeissettoAxillary, you willnotneedtopress
the mode button.
3. Attach a probe cover as described in step 2 of the OPERATION Section.
4. Lift the patient’s arm so that the entire
axilla is easily visualized.
5. Place the probe as high as possible in the
axilla. Do not allow the probe tip to come
into contact with the patient until it is
deliberately placed in the measurement
site. Any tissue contact before this time
willactivatetheprobepositioniconandmaycauseinaccuratetemperature
readings.
6. Be sure that the probe tip will be completely surrounded by axillary tissue.
Clothing or any other material touching the probe tip may cause inaccu-

11
rate readings.
7. Place the arm snugly at the patient’s side. Hold the arm in this position
without movement of the arm or probe during the measurement cycle.
Movement of the arm or probe during
this time will activate the probe position
icon and may cause inaccurate read-
ings.
9. An audible tone and display of a tem-
perature reading indicates the final tem-
perature has been reached.
10. Afterthetemperaturemeasurementiscomplete,removetheprobefromthe
patient’s axilla, then eject the probe cover by firmly pressing the ejection
button on the probe (Figure 1).
11. Insertthe probe into the storage channel to clear the display, in preparation
for taking another temperature.
TAKINGAXILLARYTEMPERATURES-BLUECAPPEDPROBE
(PATIENTSOVER4YEARSTHROUGHADULT)
Axillary temperatures for patients 4 years through adult should only be taken
when the SureTemp is in the Monitor mode using an oral probe.
1. Withdraw the oral probe from its storage channel and observe a quick
thermometer display test.
2. Attach a probe cover in the manner as
described in step 2 of the OPERATION
Section.
3. Placetheprobeintheaxillaand placearm
snugly at the patient’s side to reduce the
cooling effects of evaporation and
convection.
4. After the temperature is displayed,
depress the Mode button for more than 2
seconds. The “M”icon will appear on
theLCDindicatingtheunitisinMonitor
mode. Continue taking the temperature
reading for about 5 minutes.
5. After the Monitor mode temperature has been taken, insert the probe into

12
thestoragechanneltoclearthedisplayandresetthethermometertoNormal
mode in preparation for another temperature.
TAKINGRECTALTEMPERATURES-REDCAPPEDPROBE
1. Exchange the oral probe (blue ejection button) for the rectal probe (red
ejection button) by removing the probe from the storage channel, unplug-
ging the probe connector from the thermometer, and repeating steps 1
through 6 in the SETUP section.
2. Attach a probe cover in the same manner
as in the oral procedure. Make sure the
rEC is displayed.
3. Separate the buttocks with one hand. Us-
ing the other hand, gently insert the probe
only 1.5 cm (5/8 of an inch) inside the
rectal sphincter (less for infants and chil-
dren). The use of lubricant is optional.
WARNING: Incorrect insertion can cause bowel perforation.
Tilt the probe so the tip is touching tissue.
Keep hand separating buttocks in place.
Hold the probe in place during the entire
temperature measurement process.
4. When the final temperature is reached, a
tone will sound and the temperature will
be displayed. Rectal temperature mea-
surements will take about 15 seconds.
5. After the temperature measurement is complete, remove the probe from the
patient, then eject the probe cover by firmly pressing the ejection button on
the probe. (Figure 1).
6. Insert the probe into the storage channel to clear the display, in preparation
for another temperature.
7. Wash hands (note: washing hands greatly reduces the risk of cross-
contamination and NSI).
MAINTENANCE
Other than using a new probe cover for each temperature reading, keeping the
instrument clean, and replacing the batteries, there is no requirement for user

13
maintenance. Refer to the 679 SureTemp
Technical Service Manual for detailed
information on security settings,
sterilization, and calibration verification.
Battery Replacement
1. With thumb and forefinger, firmly
press-in on indentations located on the
sides of the rear housing. This will
release two snaps.
2. Remove the battery door.
3. Remove batteries by lifting the battery strap. IMPORTANT: After
removing the old batteries press and hold the MODE button for 5
seconds before inserting the new batteries.
4. Replace batteries with 3 AA Alkaline only. Orient per markings on the
inside of the battery well.
5. Replace the battery door by inserting two tabs into bottom of thermom-
eter and snapping back into place.
CLEANING&STERILIZATION
The 679 SureTemp housings may be cleaned with a cloth dampened with
alcohol, warm water, or a nonstaining disinfectant such as Sporicidin®Spray
and Towelettes or MetriSpray™. Care should be taken not to scratch the LCD
faceplate. Low temperature Ethylene Oxide (ETO) sterilization of Oral or
Rectal probes is to be used only when absolutely necessary. The procedure for
ETO sterilization is described in the 679 SureTemp Technical Service Manual
and is available from Customer Service.
SPECIFICATIONS
•Patient Temperature Range: 84.0°F - 108.0°F (28.9°C - 42.2°C).
•Calibration Accuracy: +0.2°F (+0.1°C).
•Dimensions(approximate): 2.25inx3inx7in(5.72cmx7.62cmx17.78cm);
weight 10.5 oz (300 gr).
CUSTOMERSERVICE
For customer service, technical or clinical support, please contact Welch Allyn
at [phone] from 7:00 AM to 5:00 PM Pacific Time.

70873-1000D
[phone] •[phone] •FAX [phone]
Welch Allyn, Inc. San Diego, CA 92121
LIMITEDWARRANTY
1-YEAR LIMITED WARRANTY ON NEW INSTRUMENTS: Instrumentation
purchased new from Welch Allyn, Inc. (Welch Allyn) is warranted to be free from original
defects in material and workmanship under normal use and service for a period of one year
from the date of first shipment from Welch Allyn. This warranty shall be fulfilled by Welch
Allynor its authorized representativerepairing or replacingatWelch Allyn's discretion,any
such defect, free of charge for parts and labor.
Welch Allyn should be notified via telephone of any defective product and the item should
be immediately returned, securely packaged and postage prepaid to Welch Allyn. Loss or
damage in shipment shall be at purchaser's risk.
Welch Allyn will not be responsible for loss associated with the use of any Welch Allyn
productthat(1)hashadtheserialnumberdefaced,(2)hasbeenrepairedbyanyoneotherthan
anauthorizedWelchAllynServiceRepresentative,(3)hasbeenaltered,or(4)hasbeenused
in a manner other than in accordance with instructions.
1-YEAR LIMITED WARRANTY ON PROBES AND PROBE COVERS:
Welch Allyn warrants probe covers and probes to meet Welch Allyn’s specifications for the
Product at the time of purchase and to be free from original defects in material and
workmanship under normal use and service for a period equal to 1 year from the date of first
shipment of such Product to the customer by or on behalf of Distributor.
THISWARRANTYISEXCLUSIVEANDINLIEUOFANYIMPLIEDWARRANTYOF
MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE, OR OTHER WAR-
RANTY OF QUALITY, WHETHER EXPRESSED OR IMPLIED. WELCH ALLYN
WILLNOTBELIABLEFOR ANY INCIDENTAL OR CONSEQUENTIALDAMAGES.