Well CHAR-CAR-CBB10-WL User manual

INSTRUCTION MANUAL
BATTERY CHARGER
Thank you for choosing WELL. Please read carefully the following instructions and keep them within reach.
Reorder No: CHAR-CAR-CBB10-WL

IMPORTANT SAFETY INSTRUCTIONS
1) Batteries generate explosive gases during normal operation. Use in well-ventilated area.
2) Consider having someone close enough to come to your aid when you work near a battery.
3) Do NOT smoke, strike a match, or cause a spark in vicinity of battery or engine.
4) Remove all personal jewelry, such as rings, bracelets, necklaces, and watches while working with a vehicle
battery. These items may produce a short-circuit that could cause severe burns.
5) Be extra cautious to reduce risk of dropping a metal tool onto the battery. It might spark or short-circuit a battery
or other electrical hardware which may cause an explosion or fire.
6) Wear complete eye protection, hand and clothing protection.
7) Study all battery manufacturer’s specific precautions such as removing or not removing cell caps while charging
and recommended rates of charge.
8) Clean battery terminals before connected with the charger. Be careful to keep corrosion from coming in contact
with eyes.
9) When it is necessary to remove a battery from vehicle to charge, always remove grounded terminal from battery
first. Make sure all accessories in the vehicle are off in order to prevent an arc.
10) It is NOT intended to supply power to an extra-low-voltage electrical system or to charge dry-cell batteries.
Charging dry-cell batteries may burst and cause injury to persons and property.
11) NEVER charge a frozen, damaged, leaking or non-rechargeable battery.
12) If battery electrolyte contacts skin or clothing, wash immediately with soap and water. If electrolyte enters eye,
immediately flood eye with running cold water for at least 15 minutes and get medical attention immediately.
SAFETY PRECAUTIONS FOR USING THE CHARGER
1) Do NOT place the charger in the engine compartment or near moving parts or near the battery; place as far away
from them as DC cable permits. Never place a charger directly above a battery being charged; gases or fluids from
battery will corrode and damage charger.
2) Do NOT cover the charger while charging.
3) Do NOT expose to rain or wet conditions.
4) Connect and disconnect DC output only after setting AC cord from electric outlet.
5) Use of an attachment not recommended by the manufacturer may result in a risk of fire, electric shock or injury to
persons.
6) To reduce the risk of damage to electric plug and cord, pull by the plug rather than the cord when disconnecting
charger.
7) To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning.
8) Operate with caution if the charger has received direct hit of force or been dropped. Have it checked and repaired
if damaged.
9) Any repair must be carried out by the manufacturer or an authorized repair agent in order to avoid danger.
CONNECTING TO THE BATTERY
1) Identify polarity of battery posts. The positive battery terminal is typically marked by these letters or symbol
(POS, P, +). The negative battery terminal is typically marked by these letters or symbol (NEG, N, -).
2) Do not make any connections to the carburetor, fuel lines, or thin metal parts.
3) Identify if you have a negative or positive grounded vehicle. This can be done by identifying which battery post
(NEG or POS) is connected to the chassis.
4) For a negative grounded vehicle (most common): connect the RED POSITIVE battery clamp first to the positive
battery terminal, then connect the BLACK NEGATIV battery clamp to the vehicle chassis or negative battery
terminal.
5) For a positive grounded vehicle (very uncommon): connect the BLACK NEGATIV battery clamp first to the
negative battery terminal, then connect the RED POSITIVE battery clamp to the vehicle chassis or positive battery
terminal.
6) When disconnecting, disconnect in the reverse sequence, removing the negative first (or positive first for positive
ground systems).
NOTICE: If battery clamps are reversely connected to battery terminals, the ERROR light will be on. Exchange the
battery clamps to solve this problem.

ABOUT PRODUCT
1) The battery charger is designed for charging all types of 12V lead-acid , including WET (Flooded), GEL, MF
(Maintenance-Free), EFB (Enhanced Flooded Battery), AGM (Absorbed Glass Mat) batteries.
2) Built-in intelligent microprocessor makes charging faster, easier and safer.
3) This charger has safety features, including spark proof, protection for reverse polarity, short circuit, overcurrent,
overcharge and overheat.
4) Auto-memory: after power on, the display window of charger will show the last selected mode (except BOOST
mode). The charger will enter charging mode in 5 seconds around.
5) When the CHARGE light is on, it is on charging; when the CHARGE light is off and FULL light is on, the
charging is completed. But do NOT break the connection immediately. It will automatically switches from full
charge to maintenance status to maintain batteries during prolonged periods of storage.
6) It shows present voltage when VOLTAGE button is pressed.
7) Following is the charger’s technical specification:
AC Input
220-240VAC, 50-60Hz, 2A
DC Output
6VDC, 2A/5A;
12VDC, 2A/5A/10A;
12VDC, 15A, 300s (BOOST);
Temperature Controlled.
Efficiency
85% Approx
Power
280W Max
Start Voltage
> 3V
Charger Type
8 steps, Full-automatic Charging Cycle
Battery Type
All Types of 6V and 12V Lead-acid Batteries
Battery Capacity
2-150Ah (6V), 2-300Ah (12V), Maintains All
Battery Sizes
Boost Mode
300s for 12V Lead-acid Batteries
Housing Protection
IP20
Ambient Temperature
0℃ ~ +40℃
CHARGING MODES
Battery charger has seven (7) modes: STANDBY, 6V/2A, 6V/5A, 12V/2A, 12V/5A, 12V/10A and BOOST. Do not
operate the charger until you confirm the appropriate charge mode for your battery.
Mode
Display
POWER
Light
Explanation
STANDBY
----------
Keep on
Not charging or providing any
power.If you want charging to
pause, press ON/OFF button and it
will enter STANDBY mode.
6V/2A
02A
Keep on
Connected to battery, it can turn
into 2A by pressing CURRENT
button. This mode is
recommended for 2-60AH
batteries.
6V/5A
05A
Keep on
Connected to battery, it can turn
into 5A by pressing CURRENT
button. This mode is
recommended for 10-150AH
batteries.

12V/2A
02A
Keep on
Connected to battery, it can turn
into 2A by pressing CURRENT
button. This mode is
recommended for 2-60AH
batteries.
12V/5A
05A
Keep on
Connected to battery, it can turn
into 5A by pressing CURRENT
button. This mode is
recommended for 10-150AH
batteries.
12V/10A
10A
Keep on
Connected to battery, it can turn
into 10A by pressing CURRENT
button. This mode is
recommended for 40-300AH
batteries.
BOOST
FAS
Keep on
Connected to battery, it can enter
BOOST mode by pressing
BOOST button. It takes 5 minutes
to charge.
BOOST mode is advanced charging mode that require your full attention before selecting.
Using 12V BOOST
To operate BOOST, the charger must be connected to a 12V lead-acid battery with the battery clamps connected. For
optimal results, allow boost to complete its 5-minute charge. After 300-second boost, digital tube will show “000”,
and your are ready to start your vehicle (whether FULL light is illuminated or not). If unsuccessful when starting
your vehicle, let the battery rest for 5 minutes and try boost again. Most vehicles will start with one (1) boost. Do not
use boost more than two (2) times within a 24-hour period. If two (2) boosts cannot successfully start your vehicle,
have your battery replaced or evaluated by a local battery store.
CHARGING STEPS
STEP 1: DIAGNOSIS (Check if battery has connected with the charger and also check battery voltage)
STEP 2: DESULPHATION (If battery voltage is too low, programs automatically generate pulsing current to
remove sulphate)
STEP 3: ANALYSE (Check if the battery voltage reaches to the threshold after desulphation, and charging begins if
the battery voltage is OK)
STEP 4: SOFT START (Charge with echelon constant current)
STEP 5: BULK (Charge with constant maximum current until battery voltage is reached to the threshold)
STEP 6: ABSORPTION (Provide gradually declining current charge for maximum battery voltage)
STEP 7: ANALYSE (Test if the battery can hold charge)
STEP 8: MAINTENANCE (Continuously monitor the battery, and charging current will intelligently adapt to the
variable battery voltage)

NOTICE: After full charging cycle, use this battery to start matched vehicle’s engine. If engine cannot be activated
(exclude the problem of vehicle itself), it indicates this battery has declined storage capacity and need to be replaced.
ERROR LIGHT
When ERROR light is on, it means the charger detects invisible fault. Therefore, the user should solve the fault before
use. If the user could not solve problems, please consult the professional person.
ERROR INDICATORS
CODE
ERRORS
SOLUTIONS
E01
Charger overheating
The charger will automatically suspend the
charge and send out a warning sound, at this
time the user does not have to cut off the
power and wait for the charger to recharge
when the charger is cooled
E02
Poor contact of battery or
battery pole leads to bad
contact
Reconnect the battery or clean the battery pole
E03
Charging mode and
battery voltage mismatch
Charging the 12V battery in the 6V mode will
cause mismatch. The charger will send out a
warning sound, at this time the user needs to
cut off the power and reselect the mode.
E04
Battery can not store
electricity
The battery has been damaged and the charger
can't repair the battery.
E05
The battery is seriously
vulcanized and cannot be
repaired
The battery has been damaged and the charger
can't repair the battery.
E06
Reverse connection
Disconnect and re-connect
Waste electrical and electronic equipment are a special waste category, collection,
storage, transport, treatment and recycling are important because they can avoid
environmental pollution and are harmful to health. Submitting waste electrical and
electronic equipment to special collection centers makes the waste to be recycled
properly and protecting the environment. Do not forget! Each electric appliance that
arrives at the landfill, the field, pollutes the environment!
Importer & distributor:
SC VITACOM ELECTRONICS SRL
CIF: RO 214527
Tel. [phone]*
[email protected], www.vitacom.ro