Well SENSE User manual

USER MANUAL
Model: SENSE
(Wireless Thermometer)
Thank you for choosing WELL. Please read carefully the following instructions and keep them within reach.
Reorder No: THERM-OUTD-SENSE-WL

OVERVIEW
MAIN UNIT
1. OUTDOOR TEMPERATURE 2. INDOOR TEMPERATURE 3.ALARM MODE 4.TIME 5.ALARM
6.HANGING HOLE 7.BATTERY COMPARTMENT 8.STANDING BRACKET
SENSOR
FEATURES
1. Alarm function
2. Indoor Temperature display with C / F selectable.
3. Indoor temperature range: -9C ~ +50C.
4. Outdoor temperature with RF
5. Outdoor temperature range: -50C ~ 70C
6. Records Min/Max temperature

GETTING STARTED
POWER SUPPLY
MAIN UNIT INSTALLATION
1. Remove the battery compartment cover.
2. Insert 2x AAA battery matching the polarity (+and-).
SENSOR INSTALLATION
1. Remove the battery compartment cover.
2. Insert 2xAAA batteries matching the polarity (+and-).
TIME SET
1. Press and hold “SET” key for 2 seconds to enter into time setting
2. The figure to be set will be flashing.
3. Press “UP””DOWN” key to change the settings
4. The setting order is: Hour, Minute.
5. Press “SET” again to confirm and exit setting.
6. If do nothing to the keys above 20seconds, it will automatically exist setting mode.
7. On normal mode, press “UP” key to change 12Hr/24Hr.
Long time holding “UP” key goes into re-registration the data of RF (Outdoor temperature)
ALARM & SNOOZE SET
ALARM SETTING
1.Press “AlARM” key to enter into AL mode.
2.Hold ”ALARM” key for 2 seconds to enter into alarm setting.
3.The figure to be set will be flashing.
4.Press “UP””DOWN” key to change the settings,
5.The setting order is: Hour Minute.
6.Press “ALARM” again to confirm and exit setting.
7.On AL mode, press ”UP” to turn alarm on/off. indicate alarm is ON
SNOOZE FUCTION
1. Touch “SNOOZE” to silence it for 5 minutes, OR
2. Press any other key to turn the alarm off and activate it again after 24 hours.
TEMPERATURE
1 The indoor temperature will display within 3~8 minutes automatically after set up.
2. The outdoor temperature will display after receive RF signal.
3. Press “DOWN” key to switch C / F
4. Press and release the “MIN/MAX” key repeatedly, the current indoor/outdoor temperature will
alternate between the MIN/MAX temperature recordings and the current value.
5. In MIN/MAX temperature display mode, press and hold “MIN/MAX” key to reset ALL indoor/outdoor
temperature MIN/MAX records to current values at the same time.

433 MHz RECEPTION CHECK
The transmission range is about 260feet (80meters) from the transmitter to the thermometer (in open
area). The thermometer should receive the temperature data with 3 minutes after set-up. If the
temperature data is not received 3 minutes after setting up, please check
1. The distance of thermometer or transmitter should be at least 5~6.5 feet (1.5~2 meters) away from
any interfering sources such as computer monitors or TV sets.
2. Avoid positioning the thermometer onto or in the immediate proximity of metal window frames.
3. Using other electrical products such as headphones or speakers operating on the same signal
frequency.
4. Neighbors sing electrical devices operating on the same signal frequency can also cause interference.
POSITIONED METHOD
The thermometer can be positioned in 2 ways as desired.
A. Pull out the table stand brackets from the rear of the thermometer, place on table or desk as desired.
B. Hang on the wall by hanging hole.
PRECAUTIONS
Do not clean any part of the product with benzene, thinner or other solvent chemicals. When necessary,
clean it with a soft cloth.
Never immerse the product in water. This can cause electrical shock and damage the product.
Do not subject the product to extreme force, shock, or fluctuations in temperature or humidity.
Do not tamper with the internal components.
Do not mix new and old batteries or batteries of different types.
Do not mix alkaline, standard or rechargeable batteries with this product.
Remove the batteries if storing this product for a long period of time.
Do not dispose of this product as unsorted municipal waste. Collection of such waste separately for
special treatment is necessary.
Waste electrical and electronic equipment are a special waste category,
collection, storage, transport, treatment and recycling are important because
they can avoid environmental pollution and are harmful to health. Submitting
waste electrical and electronic equipment to special collection centers makes
the waste to be recycled properly and protecting the environment. Do not
forget! Each electric appliance that arrives at the landfill, the field, pollutes the
environment!
Importer & distributor:
SC VITACOM ELECTRONICS SRL
CIF: RO 214527
Tel. [phone]*
[email protected]o, www.vitacom.ro