Wenger GearBoss Lock Box Accessory User manual

Installation Manual
#!$$!!'
$$!#(
!% Please read and understand the GearBoss Lock Box Accessory Owner’s Manual before
attempting installation, assembly, or use.
!% Remove all items from the shipping containers and sort the components by type, size, etc.
Refer to the illustrations on the following pages. If you need additional information about your
GearBoss Lock Box Accessory, contact the Wenger Corporation using the information
listed below.
Safety
Throughout this manual you will find &%! $ which are defined as follows.
)&%!  failure to follow the instruction may result in injury or damage to property.
Read and understand the following instructions before using or installing any GearBoss Accessory.
The GearBoss Lock Box Accessory is guaranteed free of defects in materials and workmanship for five full
years.
Our guarantee assures you of either a full refund or repair or replacement of the defective materials or
workmanship without charge, at the discretion of our Customer Service Department. Just call a Customer
Service Representative at 1-800-887-7145 and state the reason you are dissatisfied. If a product return is
necessary, your representative will issue a return authorization. This is your sole remedy for breach of this
warranty.
Should you have a question or problem with any Wenger product, don’t hesitate to call, even if the product is
past warranty. It’s important to us that all our customers be satisfied.
This is the sole warranty made by Wenger. Wenger disclaims all other warranties, including the warranties of
merchantability and fitness for a particular purpose, as well as all liability for incidental, consequential, special,
and indirect damage. Wenger liability for direct damages shall be limited to the amount you paid for the
product involved. Wenger reserves the right to make product changes without obligation to incorporate such
changes into products previously sold.
Some states do not allow the exclusion or limitation of damages or warranties, so the above may not apply to
you. This warranty gives you specific legal rights. You may also have other rights which vary from state to
state.
Warranty
©Wenger Corporation 2011 Printed in USA 06/11 Part #241A347-02
 #!#"!#%!  555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448
Questions? Call.....USA: 800-4WE GER (493-6437) • Worldwide: 1-507-455-4100 • www.wengercorp.com


Read the complete assembly procedure before you start to install the GearBoss Lock Box.
Two people are recommended for the installation of the GearBoss Lock Box.
 $% %#!$$!!'
1. Determine the location in which you would like the
lock box located on the GearBoss shelving.
2. Insert the capscrew (item 10) through the upright tube (item
18) at the desired location on the GearBoss Shelving.
ote: Be sure the head of the capscrew (item 10) is to the
outside of the upright tube (item 18).
3. Secure capscrew (item 10) with the plastic wing nut
(item 1) leaving approximately 1/4” of threads between
the upright tube (item 18) and the plastic wing nut (item 1).
4. Complete steps 1-3 on adjacent upright tube (item 18)
Make sure the location of the second capscrew (item 10) is
even with the first to ensure the lock box will be level.
5. Position the lock box to hook onto the capscrew (item 10)
between the upright tube (item 18) and the plastic wing nut
(item 1).
6. Open the door of the lock box
7. Secure the lock box in place by tightening the plastic wing nuts that are now on the inside of the lock
box.
8. To secure the bottom of the lock box, insert the capscrew (item 10) through the upright tube (item 18)
and bottom hole of the lock box. Again, make sure the head of the capscrew (item 10) is to the
outside of the lock box.
9. Using the plastic wing nut (item 1) on the inside of the lock box, secure the bottom in place.
2
1
10
1810
LOCk BOx InStaLLatIOn
Views of inside
the lock box.
Maximum Load Capacity Rating
for Lock Box is 100 lbs (45 kg).
CaUtIOn
!

3
repLaCement partS LISt
% %( $#"%!
1 4 Plastic Wing ut
2 2 Lock Box Side Plate
3 2 Lock Box Pan
4 2 Lock Box Extrusion
5 1 Lock Box Door Panel
6 3 Insert ut, #8-32
7 12 Blind Rivets, 3/16
8 2 Screw, 8-18 x 3/8
9 12 Screw, #10-16 x 3/4
  
% %( $#"%!
10 4 Capscrew, 3/8-16 x 2 3/4
11 1 Lock
12 4 Tube
13 3 Machine Screw, #8-32 x 1/2
14 12 Washer
15 1 Flush Mount Plastic Handle
16 2 Hex Socket Cap ut, 1/4-20
17 2 Machine Screw, 1/4-20 x 5/8
18 1 Cam, Off-Set, Lock
3
2
9
7
12
9
2
9
7
12
17
14
16
4
5
615
4
2
9
3
10
1
11
8
4
313
18

4
This page is intentionally blank.