Wesco WS2316U User manual

20V Max Circular saw EN
WS2316U (CSC165W)
2

1 23
10 12
13
16
11
5
6
7
4
14
15
17
18
19
20
8
9

19
20
21
18
22
23
1
1
2
2
3
Fig.A Fig.B1
Fig.B2 Fig.C1
Fig.C2 Fig.C3
Fig.D Fig.E1

0° 45°
1
2
Fig.E2 Fig.F
Fig.G Fig.H
Fig.I1 Fig.I2
Fig.J Fig.K

Fig.L
24

6EN
PRODUCT SAFETY
WARNING: Some dust created by power sanding,
sawing, grinding, drilling and other construction
activities contains chemicals known to the State of
California to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals
are:
• Lead from lead-based paints;
• Crystalline silica from bricks and cement and other
masonry products;
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and
work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic
particles.
WARNING: This product can expose you to
chemicals including lead and Di(2-ethylhexyl)
phthalate (DEHP) which are known to the State of
California to cause cancer and birth defects or other
reproductive harm. For more information go to www.
P65Warnings.ca.gov.
GENERAL POWER TOOL SAFETY WARNINGS
WARNING Read all safety warnings,
instructions, illustrations and specifications
provided with this power tool. Failure to follow all
instructions listed below may result in electric shock, fire
and/or serious injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
1) Work area safety
A) Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
B) Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
C) Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk
of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will increase
the risk of electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric
shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch on
invites accidents.
d) Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away from

7
EN
moving parts. Loose clothes, jewellery or long hair can
be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust
collection can reduce dust-related hazards.
h) Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles. A careless action can cause
severe injury within a fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
c) Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting
the power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
power tool’s operation. If damaged, have the power
tool repaired before use. Many accidents are caused
by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a hazardous
situation.
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
5) Battery tool use and care
a) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack.
b) Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
c) When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fire.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or
burns.
e) Do not use a battery pack or tool that is damaged or
modified. Damaged or modified batteries may exhibit
unpredictable behaviour resulting in fire, explosion or risk
of injury.
f) Do not expose a battery pack or tool to fire
or excessive temperature. Exposure to fire or
temperature above 265°F may cause explosion.
g) Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specified in the instructions. Charging
improperly or at temperatures outside the specified
range may damage the battery and increase the risk of
fire.
6) Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
b) Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
SAFETY INSTRUCTIONS FOR ALL SAWS
CUTTING PROCEDURES
a) DANGER: Keep hands away from cutting
area and the blade. Keep your second hand
on auxiliary handle, or motor housing. If both hands
are holding the saw, they cannot be cut by the blade.
b) Do not reach underneath the workpiece. The
guard cannot protect you from the blade below the

8EN
workpiece.
c) Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth
should be visible below the workpiece
d) Never hold the workpiece in your hands or across
your leg while cutting. Secure the workpiece to a
stable platform. It is important to support the work
properly to minimise body exposure, blade binding, or
loss of control.
e) Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
tool may contact hidden wiring. Contact with a
“live” wire will also make exposed metal parts of
the power tool “live” and could give the operator an
electric shock.
f) When ripping, always use a rip fence or straight
edge guide. This improves the accuracy of cut and
reduces the chance of blade binding.
g) Always use blades with correct size and shape
(diamond versus round) of arbour holes. Blades that
do not match the mounting hardware of the saw will
run off-centre, causing loss of control.
h) Never use damaged or incorrect blade washers
or bolt. The blade washers and bolt were specially
designed for your saw, for optimum performance and
safety of operation.
FURTHER SAFETY INSTRUCTIONS FOR ALL
SAWS
Kickback causes and related warnings
— kickback is a sudden reaction to a pinched, jammed or
misaligned saw blade, causing an uncontrolled saw to lift up
and out of the workpiece toward the operator;
—when the blade is pinched or jammed tightly by the kerf
closing down, the blade stalls and the motor reaction drives
the unit rapidly back toward the operator;
— if the blade becomes twisted or misaligned in the cut,
the teeth at the back edge of the blade can dig into the top
surface of the wood causing the blade to climb out of the kerf
and jump back toward the operator.
Kickback is the result of saw misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below.
a) Maintain a firm grip with both hands on the saw
and position your arms to resist kickback forces.
Position your body to either side of the blade, but
not in line with the blade. Kickback could cause the
saw to jump backwards, but kickback forces can be
controlled by the operator, if proper precautions are
taken.
b) When blade is binding, or when interrupting a cut
for any reason, release the trigger and hold the saw
motionless in the material until the blade comes
to a complete stop. Never attempt to remove the
saw from the work or pull the saw backward while
the blade is in motion or kickback may occur.
Investigate and take corrective actions to eliminate
the cause of blade binding.
c) When restarting a saw in the workpiece, centre the
saw blade in the kerf so that the saw teeth are not
engaged into the material. If a saw blade binds, it
may walk up or kickback from the workpiece as the
saw is restarted.
d) Support large panels to minimise the risk of blade
pinching and kickback. Large panels tend to sag
under their own weight. Supports must be placed
under the panel on both sides, near the line of cut
and near the edge of the panel.
e) Do not use dull or damaged blades. Unsharpened or
improperly set blades produce narrow kerf causing
excessive friction, blade binding and kickback.
f) Blade depth and bevel adjusting locking levers
must be tight and secure before making the cut. If
blade adjustment shifts while cutting, it may cause
binding and kickback.
g) Use extra caution when sawing into existing walls
or other blind areas. The protruding blade may cut
objects that can cause kickback.
SAFETY INSTRUCTIONS FOR SAWS
(CIRCULAR SAW WITH INNER PENDULUM
GUARD)
Lower Guard Function
a) Check the lower guard for proper closing before
each use. Do not operate the saw if the lower
guard does not move freely and close instantly.
Never clamp or tie the lower guard into the open
position. If the saw is accidentally dropped, the lower
guard may be bent. Raise the lower guard with the
retracting handle and make sure it moves freely and
does not touch the blade or any other part, in all
angles and depths of cut.
b) Check the operation of the lower guard spring. If
the guard and the spring are not operating properly,
they must be serviced before use. Lower guard may
operate sluggishly due to damaged parts, gummy
deposits, or a build-up of debris.
c) The lower guard may be retracted manually only for

9
EN
special cuts such as “plunge cuts” and “compound
cuts.” Raise the lower guard by retracting handle and
as soon as the blade enters the material, the lower
guard must be released. For all other sawing, the
lower guard should operate automatically.
d) Always observe that the lower guard is covering
the blade before placing the saw down on bench
or floor. An unprotected, coasting blade will cause
the saw to walk backwards, cutting whatever is in its
path. Be aware of the time it takes for the blade to
stop after switch is released.
ADDITIONAL SAFETY RULES FOR YOUR CIRCULAR SAW
1. Only use saw blades recommended in the specification.
2. Do not use any abrasive wheels.
3. Use only blade diameter(s) in accordance with the
markings.
4. Identify the correct saw blade to be used for the
material to be cut.
5. Use only saw blades that are marked with a speed
equal or higher than the speed marked on the tool.
SAFETY WARNINGS FOR BATTERY PACK
a) Do not dismantle, open or shred battery pack.
b) Do not expose battery pack to heat or fire. Avoid
storage in direct sunlight.
c) Do not short-circuit a battery pack. Do not store
battery packs haphazardly in a box or drawer
where they may short-circuit each other or be short-
circuited by other metal objects. When battery pack is
not in use, keep it away from other metal objects, like
paper clips, coins, keys, nails, screws or other small
metal objects, that can make a connection from one
terminal to another. Shorting the battery terminals
together may cause burns or fire.
d) Do not remove battery pack from its original
packaging until required for use.
e) Do not subject battery pack to mechanical shock.
f) In the event of battery leaking, do not allow the
liquid to come in contact with the skin or eyes. If
contact has been made, wash the affected area
with copious amounts of water and seek medical
advice.
g) Observe the plus (+) and minus (–) marks on the
battery back and equipment and ensure correct
use.
h) Do not use any battery pack which is not designed
for use with the equipment.
i) Keep battery pack out of the reach of children.
j) Seek medical advice immediately if a cell or
battery has been swallowed.
k) Always purchase the battery pack recommended
by the device manufacturer for the equipment.
l) Keep battery pack clean and dry.
m) Wipe the battery pack terminals with a clean dry
cloth if they become dirty.
n) Battery pack needs to be charged before use.
Always use the correct charger and refer to the
manufacturer’s instructions or equipment manual
for proper charging instructions.
o) Do not leave battery pack on prolonged charge
when not in use.
p) After extended periods of storage, it may
be necessary to charge and discharge the
battery pack several times to obtain maximum
performance.
q) Battery pack gives its best performance when it is
operated at normal room temperature (20 °C ± 5
°C).
r) When disposing of battery packs, keep battery
packs of different electrochemical systems
separate from each other.
s) Recharge only with the charger specified by
WESCO. Do not use any charger other than that
specifically provided for use with the equipment.
A charger that is suitable for one type of battery pack
may create a risk of fire when used with another
battery pack.
t) Retain the original product literature for future
reference.
u) Use only the battery pack in the application for
which it was intended.
v) Remove the battery pack from the equipment
when not in use.
w) Dispose of properly.
INFORMATION FOR RADIATED EMISSION
This device complies with Canadian ICES-001.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not
expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part

10 EN
15 of the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
SYMBOLS
To reduce the risk of injury, user must read
instruction manual
Warning
Wear ear protection
Wear eye protection
Wear dust mask
Li-Ion battery, battery must be recycled
Indoor use only (Charger)
Read the operator’s manual.
Batteries may enter water cycle if disposed
improperly, which can be hazardous for
ecosystem. Do not dispose of waste batteries as
unsorted municipal waste.
Do not burn
COMPONENT LIST
1. Lock-off Button
2. On/Off Switch
3. Front Handle
4. Spindle Lock Button
5. Base Plate Angle Scale
6. Base Plate Bevel Lock Knob
7. Parallel Guide Lock Knob
8. Cutting Mark - 45°
9. Cutting Mark - 0°
10. Parallel Guide
11. Blade Rotation indicator
12. Base Plate
13. Lower Guard Lever
14. Saw Blade
15. Lower Blade Guard
16. Fixed Guard
17. Vacuum Adapter
18. Battery Pack
19. Battery Pack Release Button
20. Main Handle
21. Inner Flange (See Fig. C3)
22. Outer Flange (See Fig. C3)
23. Blade Bolt (See Fig. C3)
24. Cutting Depth Scale (See Fig. D)
25. Cutting Depth Lock Knob (See Fig. D)
26. Hex key (See Fig. L)
* Not all the accessories illustrated or described are included
in standard delivery.
POSITEC Inc. has established a partnership with the
RBRC Corporation to recycle any Positec batteries
with the RBRC-call2recycle seal. For environmental
protection, please do not discard batteries in the
trash. After the batteries‘ life cycle is ended, then
please call 1-800-822-8837 for a free service that
will properly dispose of the battery.

11
EN
TECHNICAL DATA
Type WS2316U(CSC165W) (23-designation of
machinery, representative of circular saw)
Voltage 20V Max**
No load speed 4000/min
Blade size 6-1/2”(165mm)
Cutting capacity 90° 2-5/64”(53mm)
45° 1-27/64”(36mm)
Bevel capacity 0-45°
Charger protection class / II
Charger input (WS9924U) 120V~60Hz 55W
Charger output (WS9924U) 20V 2.0A
Battery pack (WS9940) 4.0 Ah Li-ion
**Voltage measured without workload. Initial battery voltage
reaches maximum of 20 volts. Nominal voltage is 18 volts.
ACCESSORIES
Allen key 1
parallel guide 1
40T saw blade 1
24T saw blade 1
Battery pack (WS9940) 1
Charger (WS9924U) 1
We recommend that you purchase your accessories listed
in the above list from the same store that sold you the tool.
Refer to the accessory packaging for further details. Store
personnel can assist you and offer advice.
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the instruction
book carefully.
INTENDED USE:
The machine is intended for use around the
home and domestic applications. It is particularly useful
for trimming plywood and similar sheet material. It is NOT
suitable for metal cutting blades or discs.
BEFORE OPERATION
1. CHARGING THE BATTERY PACK
a)Do not use any charger other than that specifically
provided for use with the equipment.
b) If the battery pack is very hot you must remove your
battery pack from the charger and allow time for the battery
to cool down before recharging.
c) The battery in your new tool is not charged when it leaves
the plant. Therefore it must be full charged before using the
first time.
d) Please charge the battery to reach full or no less than half
charge before storage. If the tool will not be used for long
periods of time, charge the battery every 3-6 months.
CHARGING PROCEDURE (SEE FIG. A)
1) Plug the charger into an appropriate outlet. The light will
be green.
2) Slide the battery pack into the charger, the light will turn
to red to indicate the charging process has started.
3) When charging is completed, the light will turn to green.
The pack is now fully charged, unplug the charger and
remove the battery pack.
CHARGING INDICATOR
This charger is designed to detect some problems that can
arise with battery packs. Indicator lights indicate problems
(see table below). If this occurs, insert a new battery
pack to determine if the charger is OK. If the new battery
charges correctly, then the original pack is defective and
should be returned to a service center or recycling service
center. If the new battery pack displays the same problem
as the original Battery Pack, have the charger tested at an
authorized service center.
Light Status
Red on Charging
Green on Fully Charged
WARNING: When battery charge runs out after
continuously use or exposure to direct sunlight
or heat, allow time for the tool to cool down before re-
charging to achieve the full charge.

12 EN
2. REMOVE OR INSERT BATTERY PACK (SEE FIG. B1,B2)
Press the battery pack release button and remove the
battery pack from the tool. After recharge slide the battery
pack into tool’s battery port. A simple push and slight
pressure will be sufficient.
OPERATION
WARNING: Before undertaking any
maintenance or adjustment, ensure the saw
is switched off and battery pack is removed.
Wear protective gloves when mounting the saw
blade.
1. FITTING/CHANGING A SAW BLADE
Danger of injury when touching the saw blade.
Only use saw blades that correspond with the
technical specification data for this tool.
Do not under any circumstances use grinding discs
as the cutting tool.
For changing the saw blade, it is best to place the machine
on with the motor end cap on a flat surface with the blade
and blade guard area facing upwards.
Removing the saw blade:
Press the spindle lock button and keep it depressed.
Loosen the blade bolt in a clockwise direction using the
supplied hex key Remove the outer flange. Using the lower
guard lever, tilt back the lower blade guard and hold it firmly
in this position. Remove the saw blade.(See Fig.C1,C2)
Mounting the saw blade:
Using the lower guard lever, tilt back the lower blade guard
and hold it firmly in this position. Place the saw blade onto
the inner flange. Ensuring that the direction of the
cutting teeth on the saw blade match the direction of
the blade rotation indicator. Place the the outer flange
over the blade, then insert the blade bolt. Press the spindle
lock button to lock the spindle, then use the supplied hex
key to tighten the blade bolt in an anti-clockwise direction
with 1/4 turn more than finger tight.
NOTE: Take care that the mounting positions of the
inner flange and outer flange are correct.( See Fig.C3)
WARNING: Blade teeth are very sharp. For best
cutting results ensure you use a saw blade suited to
the material and cut quality you need.
2. DEPTH OF CUT ADJUSTMENT (See Fig. D)
Turn the cutting depth lock knob in an anti-clockwise
direction, and raise the saw body away from the base plate.
Set the depth of cut using the cutting depth scale and
then turn the cutting depth lock knob in an anti-clockwise
direction. Always add 3mm to your depth of cut so that the
blade can cut through the material.
3. BASE PLATE ANGLE ADJUSTMENT (See Fig. E1, E2)
Turn the base plate bevel lock in anti-clockwise direction
to loosen the angle scale. Tilt the base plate away from the
machine until the required cutting angle is adjusted on the
angle scale. Tighten the bevel lock by turning it in clockwise
direction. Do not use the the cutting depth scale when
making bevel cuts due to possible inaccuracy.
4. DUST EXTRACTION OUTLET (See Fig. F)
Fasten the vacuum adapter onto the dust extraction outlet
until it latches. Additionally fasten the vacuum adapter to the
fixed guard with the two screws. Directly connect a suitable
vacuum hose to the adapter.
●The vacuum adapter must not be mounted when
no external dust extraction is connected. Otherwise
there is danger of the extraction system becoming
clogged.
Clean the vacuum adapter regularly to ensure optimum
dust extraction. The vacuum cleaner must be suitable
for the material to be worked.
5. HAND GRIP POSITION (See Fig. G)
Always hold your saw firmly with both hands when
operating.
6. SAFETY ON/OFF SWITCH (See Fig. H)
Your switch is locked off to prevent accidental starting.
Depress the lock off button then the on/off switch and
release the lock off button. Your switch is now on. To switch
off, just release the on/off switch.
The blade may continue to rotate after switching off. Wait
until the machine comes to a complete stop before setting
down.
7. CUTTING GUIDE (See Fig. I1, I2)
There is a cutting mark notch on the front of the base plate
for use with a parallel guide. For straight cuts, use the 0º
cutting mark to align with your parallel guide scale. For a 45º
bevel cut, use the 45º cutting mark to align with your parallel
guide scale. Securely clamp the parallel guide. Always make
a trial cut to check the setting.
8. PARALLEL GUIDE ADJUSTMENT (See Fig. J)
It is used for making cuts parallel to a workpiece edge at a
chosen distance. Slide the parallel guide arm through the
fixture to achieve the required cutting distance then tighten
the lock knob to clamp. It can be used from both sides of
the base plate. For straight cuts, use the 0° guide mark to
align with your parallel guide scale. For a 45° bevel cut, use
the 45° guide mark to align with your parallel guide scale.

13
EN
Securely clamp the parallel guide.
NOTE: It is best to carry out a trial cut.
9. BEVEL CUTS (See Fig. K)
Set the required bevel angle between 0° and 45°. Do not
use the depth of cut scale when making bevel cuts due to
possible inaccuracy.
10. HEX KEY STORAGE (See Fig. L)
The supplied hex key provided can be placed in the area
under the machine motor.
WORKING HINTS FOR YOUR CIRCULAR
SAW
If your power tool becomes too hot, run your circular saw
no load for 2-3 minutes to cool the motor. Avoid prolonged
usage at very low speeds.
Always use a blade suited to the material and material
thickness to be cut. The quality of cut will improve as the
number of blade teeth increase.
Always ensure the work-piece is firmly held or clamped to
prevent movement. Support large panels close to the cut
line. Any movement of the material may affect the quality
of the cut. The blade cuts on the upward stroke and may
chip the uppermost surface or edges of your work piece.
When cutting, ensure your uppermost surface is a non-
visible surface when your work is finished. Feeding too fast
significantly reduces the performance of the machine and
shortens the life of the saw blade. Always face the good side
of the work-piece down, to ensure minimum splintering.
Only use sharp saw blades of the correct type.
MAINTENANCE
Remove the battery pack before carrying out any
adjustment, servicing or maintenance.
Your power tool requires no additional lubrication or
maintenance. There are no user serviceable parts in your
power tool. Never use water or chemical cleaners to clean
your power tool. Wipe clean with a dry cloth. Always store
your power tool in a dry place. Keep the motor ventilation
slots clean. Keep all working controls free of dust.
Occasionally you may see sparks through the ventilation
slots. This is normal and will not damage your power tool.
For Battery tools
The ambient temperature range for the use and storage of
tool and battery is 0 oC (44.6 oF)-45oC (113 oF).
The recommended ambient temperature range for the
charging system during charging is 0 oC (44.6 oF)-40 oC
(104 oF).
FCC PART 15
Supplier’s Declaration of Conformity
Product Description: Battery charger
Model Number: WS9924U
Trade Name: WESCO
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and
(2) This device must accept any interference received,
including interference that may cause undesired
operation.
Responsible Party :
Positec USA, Inc.
10130 Perimeter Parkway, Charlotte, NC 28216 USA
Tel.: [phone]
Fax: [phone]