West Elm bergen User manual

bergen closet wide 3 drawer
assembly instructions
Page  of 798223 / 9899 - 0/07
! Tools required:
! Do not throw away packaging materials until assembly is complete.
! Assemble this item on a soft surface, such as cardboard or carpet, to protect nish.
A
wooden dowel 8x
B
large cam lock 8x
D
C
small dome screw 6x
F
G
E
I
JL
M
mounting plate x large screw 6x
felt pad 6x
cam screw 4x
smalll screw 4x
small cam lock 6x
drawer glide 6x
drawer handle with screws 3x

bergen closet wide 3 drawer
assembly instructions
Page 2 of 798223 / 9899 - 0/07
Left
Right
bottom edge
bottom edge
3rd hole from the front
L
D
1st hole from the back
L
D
. Attach drawer glides (L) to side panels using small screws (D) as shown. The FRONT of each drawer glide should be fastened
through the third round hole from the front of the glide. The BACK of each drawer glide should be fastened through the rst round
hole from the back of the glide. Bottom glides attach into the rst set of pilot holes from the bottom edge of the cabinet. Middle
glides attach to third set of pilot holes from the bottom edge. Top glides attach to the fth pilot holes up from the bottom edge.
A
2. Using a hammer or mallet, tap in wooden dowels (A) into holes in side panels as shown.

bergen closet wide 3 drawer
assembly instructions
Page 3 of 798223 / 9899 - 0/07
3. Insert large cam locks (C) into holes in side panels. Make sure arrow on face of each cam lock is pointed in the direction of the
hole in the edge of each panel as shown.
4. Insert cam screws (B) into holes provided on top and bottom panels as shown. Tighten cam screws with a phillips screwdriver.
B
C

bergen closet wide 3 drawer
assembly instructions
Page 4 of 798223 / 9899 - 0/07
5. Fasten side panels to bottom panel as shown. Fit cam screws into cam locks and tighten using a phillips screwdriver.
6. Slide back panel into groove. Make sure panel slides all the way into the bottom panel groove.
7. Fasten top panel to side panels. Fit cam screws into cam locks and tighten using a phillips screwdriver.

bergen closet wide 3 drawer
assembly instructions
Page 5 of 798223 / 9899 - 0/07
8. Insert small cam locks (F) into each drawer side panel. Make sure arrow on face of each cam lock is pointed in the direction of
the hole on the edge of each panel as shown.
9. Insert cam screws (B) into drawer front panels. Tighten with phillips screwdriver.
F
B
0. Attach drawer side panels to back panels using one large screw (I) per drawer side. Slide the bottom panel into the groove.
I

bergen closet wide 3 drawer
assembly instructions
Page 6 of 798223 / 9899 - 0/07
. Attach drawer fronts to drawer sides. Fit cam screws into cam locks and tighten using a phillips screwdriver.
2. Attach drawer handles (J) to drawer fronts using the 2 screws supplied with each handle. Tighten using phillips screwdriver.
J

bergen closet wide 3 drawer
assembly instructions
Page 7 of 798223 / 9899 - 0/07
3. Slide drawers onto glides and fasten together with small dome screws (E) from inside the drawer into the hole in the glide.
Tighten with a phillips screwdriver.
CARE INSTRUCTIONS
Hardware may loosen over time. Periodically check that all connections are tight.
Wipe with a soft, dry cloth. To protect nish, avoid the use of chemicals and household cleaners.
4. Multiple units can be attached together as shown using small screws (D) and mounting plates (G). If combining side-by-side
use felt pads (M) between units to minimize scratching.
D
G
E