West Elm Pivot Storage Bed User manual

pivot storage bed full size
assembly instructions
-09.15.09 Page 1 of 7
! Tools Required:
! Do not throw away packaging materials until assembly is complete.
! Assemble this item on a soft surface, such as: cardboard or carpet to protect finish.
! Proper assembly of this item requires 2 people.
Hardware
1
bolt 6mm x 40mm 12x
spring washer 12x
flat washer 12x
cam bolt 12x
cam lock 12x
screw Ø4mm x 20 mm 28x
dowel Ø10mm x 30 mm 12x
allen key M4 1x
2
3
4
5
6
7
8
9
10
11
12
13
14
bolt M8 x 45mm 6x
hexagon-nut M8 x 7mm 12x
crosshead bolt M6 x 20mm 10x
flat washer 10x
allen key M5 1x
spanner wrench 1x

pivot storage bed full size
assembly instructions
-09.15.09 Page 2 of 7
Parts
A
B
C
F
D
C
E
GJ
I
H

pivot storage bed full size
assembly instructions
-09.15.09 Page 3 of 7
1. Insert dowels (7) into the holes of the headboard (A) and the footboard (B). Attach the corner blocks (D) to
at washers (3). Tighten with
allen key (8).
2. Insert cam bolts (4) to the side rails (C) and the footboard (B) as shown below. Tighten with phillips head
screwdriver.

pivot storage bed full size
assembly instructions
-09.15.09 Page 4 of 7
3. Attach the side rails (C) to the headboard (A) and the footboard (B) with bolts (1), spring washers (2),
at washers (3). Tighten with allen key (8). Insert cam lock (5) into the headboard (A), and side rails (C).
Tighten cam locks (5) with phillips head screwdriver as shown below.
4. Insert dowels (7) to legs (E) before attaching the legs (E) to the corner blocks (D) with bolts (1), spring
at washers (3) as shown below. Tighten bolts (1) with allen key (8).

pivot storage bed full size
assembly instructions
-09.15.09 Page 5 of 7
5. Lay the bottom panels (F) between the side rails (C), making sure that the panel that has 2 rails under-
neath is located in the center. Attach bottom panels (F) to the bed frame with screws (6) as shown below.
6. Attach the handle (I) and stoppers (J) to the metal slats frame (G) with hexagon-nuts (10). Tighten hexagon
nuts with spanner wrench (14).

pivot storage bed full size
assembly instructions
???????-09.15.09 Page 6 of 7
7. Turn the metal frame over and attach the two hydraulic arms (H) to the metal slats frame (G) with bolts (9),
and hexagon-nuts (10). Tighten with allen key (13) and spanner wrench (14).
8. Turn the assembled metal slats frame upright with a helper and attach the hydraulic arms (H) to the side
rails (C) with crosshead bolts (11), and at washers (12). Tighten with phillips head screwdriver.

pivot storage bed full size
assembly instructions
-09.15.09 Page 7 of 7
9. To close the storage bed, open the latches on the footboard and pull the metal slats frame down and lock
latches as shown below. To open the storage bed, open the latches and pull metal slats frame up as shown
below.
CARE INSTRUCTIONS
Hardware may loosen over time. Periodically check that all connections are tight.
nish, avoid the use of chemicals and household cleaners.
Make sure lock is enganged when mattress is not on metal frame to be sure that the metal frame does not
raise unexpectedly.