Whelen Engineering Company WeCanX Inner Edge FST User manual

Page 1
Installation Guide:
WeCanX™ Inner Edge® FST Interior Lightbar
©2019 Whelen Engineering Company Inc.
Form No.14C75B (021320)
Automotive: Lightbars
For warranty information regarding this product, visit www.whelen.com/warranty
• Proper installation of this product requires the installer to have a good understanding of automotive electronics, systems and procedures.
• Whelen Engineering requires the use of waterproof butt splices and/or connectors if that connector could be exposed to moisture.
• Any holes, either created or utilized by this product, should be made both air- and watertight using a sealant recommended by your vehicle
manufacturer.
• Failure to use specified installation parts and/or hardware will void the product warranty.
• If mounting this product requires drilling holes, the installer MUST be sure that no vehicle components or other vital parts could be damaged
by the drilling process. Check both sides of the mounting surface before drilling begins. Also de-burr the holes and remove any metal shards
or remnants. Install grommets into all wire passage holes.
• If this manual states that this product may be mounted with suction cups, magnets, tape or Velcro®, clean the mounting surface with a 50/50
mix of isopropyl alcohol and water and dry thoroughly.
• Do not install this product or route any wires in the deployment area of your air bag. Equipment mounted or located in the air bag deployment
area will damage or reduce the effectiveness of the air bag, or become a projectile that could cause serious personal injury or death. Refer to
your vehicle owner’s manual for the air bag deployment area. The User/Installer assumes full responsibility to determine proper mounting
location, based on providing ultimate safety to all passengers inside the vehicle.
• For this product to operate at optimum efficiency, a good electrical connection to chassis ground must be made. The recommended
procedure requires the product ground wire to be connected directly to the NEGATIVE (-) battery post (this does not include products that use
cigar power cords).
• If this product uses a remote device for activation or control, make sure that this device is located in an area that allows both the vehicle and
the device to be operated safely in any driving condition.
• Do not attempt to activate or control this device in a hazardous driving situation.
• This product contains either strobe light(s), halogen light(s), high-intensity LEDs or a combination of these lights. Do not stare directly into
these lights. Momentary blindness and/or eye damage could result.
• Use only soap and water to clean the outer lens. Use of other chemicals could result in premature lens cracking (crazing) and discoloration.
Lenses in this condition have significantly reduced effectiveness and should be replaced immediately. Inspect and operate this product
regularly to confirm its proper operation and mounting condition. Do not use a pressure washer to clean this product.
• It is recommended that these instructions be stored in a safe place and referred to when performing maintenance and/or reinstallation of this
product.
• FAILURE TO FOLLOW THESE SAFETY PRECAUTIONS AND INSTRUCTIONS COULD RESULT IN DAMAGE TO THE PRODUCT OR VEHICLE
AND/OR SERIOUS INJURY TO YOU AND YOUR PASSENGERS!
Warnings to Installers
Whelen’s emergency vehicle warning devices must be properly mounted and wired in order to be effective and safe. Read and follow all of Whelen’s written
instructions when installing or using this device. Emergency vehicles are often operated under high speed stressful conditions which must be accounted for
when installing all emergency warning devices. Controls should be placed within convenient reach of the operator so that they can operate the system without
taking their eyes off the roadway. Emergency warning devices can require high electrical voltages and/or currents. Properly protect and use caution around
live electrical connections.Grounding or shorting of electrical connections can cause high current arcing, which can cause personal injury and/or vehicle
damage, including fire. Many electronic devices used in emergency vehicles can create or be affected by electromagnetic interference. Therefore, after
installation of any electronic device it is necessary to test all electronic equipment simultaneously to insure that they operate free of interference from other
components within the vehicle. Never power emergency warning equipment from the same circuit or share the same grounding circuit with radio
communication equipment. All devices should be mounted in accordance with the manufacturer’s instructions and securely fastened to vehicle elements of
sufficient strength to withstand the forces applied to the device. Driver and/or passenger air bags (SRS) will affect the way equipment should be mounted. This
device should be mounted by permanent installation and within the zones specified by the vehicle manufacturer, if any. Any device mounted in the deployment
area of an air bag will damage or reduce the effectiveness of the air bag and may damage or dislodge the device. Installer must be sure that this device, its
mounting hardware and electrical supply wiring does not interfere with the air bag or the SRS wiring or sensors. Mounting the unit inside the vehicle by a
method other than permanent installation is not recommended as unit may become dislodged during swerving; sudden braking or collision. Failure to follow
instructions can result in personal injury. Whelen assumes no liability for any loss resulting from the use of this warning device. PROPER INSTALLATION
COMBINED WITH OPERATOR TRAINING IN THE PROPER USE OF EMERGENCY WARNING DEVICES IS ESSENTIAL TO INSURE THE SAFETY OF
EMERGENCY PERSONNEL AND THE PUBLIC.
Warnings to Users
Whelen’s emergency vehicle warning devices are intended to alert other operators and pedestrians to the presence and operation of emergency vehicles and
personnel. However, the use of this or any other Whelen emergency warning device does not guarantee that you will have the right-of-way or that other
drivers and pedestrians will properly heed an emergency warning signal. Never assume you have the right-of-way. It is your responsibility to proceed safely
before entering an intersection, driving against traffic, responding at a high rate of speed, or walking on or around traffic lanes. Emergency vehicle warning
devices should be tested on a daily basis to ensure that they operate properly. When in actual use, the operator must ensure that both visual and audible
warnings are not blocked by vehicle components (i.e.: open trunks or compartment doors), people, vehicles, or other obstructions. It is the user’s responsibility
to understand and obey all laws regarding emergency warning devices. The user should be familiar with all applicable laws and regulations prior to the use of
any emergency vehicle warning device. Whelen’s audible warning devices are designed to project sound in a forward direction away from the vehicle
occupants. However, because sustained periodic exposure to loud sounds can cause hearing loss, all audible warning devices should be installed and
operated in accordance with the standards established by the National Fire Protection Association.
Safety First
This document provides all the necessary information to allow your Whelen product to be properly and safely installed. Before beginning the installation and/or
operation of your new product, the installation technician and operator must read this manual completely. Important information is contained herein that could
prevent serious injury or damage.
WARNING: This product can expose you to chemicals including Methylene Chloride which is known to the State of California to cause cancer, and
Bisphenol A, which is known to the State of California to cause birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
51 Winthrop Road
Chester, Connecticut 06412-0684
Phone: [phone]
Internet: www.whelen.com
Sales e-mail: [e-mail]
Customer Service e-mail: [email protected]
®
ENGINEERING COMPANY INC.

Page 2
Tahoe & Silverado:
The Tahoe and Silverado have a
retainer which holds the headliner
to the visor clip. The retainer must
be replaced with the supplied
spacer.
Fig. 1
SPACER
HEADLINER
BRACKET
HEADLINER
VISOR CLIP
side view
VISOR CLIP
side view
VISOR CLIP
side view
SPACER
Mounting
Bracket
ROOFROOF
#8-32 x 3/8 Torx
Hd Screw (QTY 2)
R
U
BBER
S
EAL
Lightbar Side ViewLightbar Side View
WI
N
DS
H
IE
L
D
PASSENGER
SIDE
Under visor
swivel bracket Under
visor clip
Explorer bracket
shown for example
#8 - 32 X 3/8 Torx
Hd Screw
IMPORTANT! The lightbar should be located a minimum of 16" from
any radio antennas!
Installation:
Note: When routing wires, it is important to choose a path that will keep
the wires away from excessive heat or any vehicle equipment that could
compromise the integrity of the wires (ex. trunk lids, door jams, etc.)
1. Using a screwdriver, loosen (do not remove) the three screws securing the
passenger-side visor swivel bracket to the vehicle. (See reference to
retainer in Figure 1 for Silverado and Tahoe)
2. Remove the screws securing the visor clip to the vehicle. Remove and
retain the clip and all hardware.
3. Secure the bracket to the Inner Edge housing using the hardware provided.
4. Position the keyed opening of the mounting bracket directly under the
mounting location for the visor clip. With the bracket in position, remount
the visor clip in its original location using the original hardware (Fig. 1).
5. Firmly tighten any hardware loosened in this procedure.
6. Repeat this procedure for the driver-side assembly.
7. When properly mounted, the rubber seal will be in full contact with the
vehicle windshield and roof. This is to prevent light output from entering the
passenger compartment. When this has been achieved, tighten mounting
hardware firmly to maintain contact (Fig. 1).
8. Route the lightbar cable down the vehicle A-pillar to your control head.
9. Make all wiring connections using the information in the wiring diagram.
Wiring and Operation WeCanX Lightbar:
Connecting the Power Cable:
WARNING! All customer supplied wires that connect to the positive terminal
of the battery must be sized to supply at least 125% of the maximum operating
current and FUSED at the battery to carry that load. DO NOT USE CIRCUIT
BREAKERS WITH THIS PRODUCT!
1. Follow the factory wiring harness through the fire wall. It may be necessary to drill
a hole in the fire wall. Make sure that there are no components that could be
damaged by drilling. After the hole has been drilled, insert a grommet to protect
the cable.
2. Route the cable along the factory wiring harness towards the battery. Install a 25
amp fuse block (customer supplied) on the end of the RED wire in the power
cable. NOTE: Remove the fuse from the fuse block before connecting any
wires to the battery.
3. Connect the BLACK wire to Chassis Ground.
Connecting the Communication Cable:
Splice the GREEN and GREY wires from the lightbar to the GREEN and GREY wires
from the Whelen WeCanX Controller.
CAUTION! DO NOT LOOK DIRECTLY AT THESE LED’S WHILE THEY ARE ON.
MOMENTARY BLINDNESS AND/OR EYE DAMAGE COULD RESULT!
IMPORTANT WARNING!
IMPORTANT NOTE: A WeCanX™ lightbar is only compatible with the Whelen Core Command System and can not be used alone or with any
other control system.
POWER CABLE
RED (+)12VDC
Chassis GroundBLACK
Fuse @ 25 Amps
COMMUNICATIONS CABLE
GREEN / CAN H
SHIELD WIRE
GREY / CAN L

Page 3
Installation Ford Fusion:
IMPORTANT AIR BAG WARNING! Do not install this product or route
any wires in the deployment area of your air bag. Equipment
mounted or located in the air bag deployment area will damage or
reduce the effectiveness of the air bag, or become a projectile that
could cause serious personal injury or death. Refer to your vehicle
owners manual for the air bag deployment area. The User/ Installer
assumes full responsibility to determine proper mounting location,
based on providing ultimate safety to all passengers.
IMPORTANT! The lightbar should be located a minimum of 16" from
any radio antennas!
Note: When routing the wires, it is important to choose a path that
will keep the wires away from excessive heat or any vehicle
equipment that could compromise the integrity of the wires (ex.
trunk lids, door jams, etc.)
Figures 1 thru 3 show the driver side of the interior of the vehicle, shown
looking up at the roof.
1. On the driver side visor swivel bracket, carefully pry the plastic
cover off the front of the bracket (Fig. 1). The lightbar mounting
bracket will sit in the space that the cover occupied. NOTE: Pry the
cover off using two flat blade screwdrivers on each side to
avoid braking the cover. The cover will not be used but should
be saved in case you wish to remove the lightbar in the future.
2. Remove the swivel bracket mounting clip (located under the cover
you removed in step 1) and lift the swivel bracket assembly out.
Install the supplied fastex grommet into the hole in the roof sheet
metal which the clip snapped into. Reinsert the swivel bracket
assembly (Figs. 1 & 2).
3. On the vehicle visor clip, remove the screw holding on the clip and
remove the clip. The supplied #8 X 1" sheet metal screw will replace
the screw you removed (Fig. 2).
4. Secure the mounting bracket to the lightbar and position the bracket
where it will mount on the vehicle (Figs. 3 & 4).
5. Secure the lightbar bracket to the swivel mount using the supplied
1/4 X 1-1/4” Phillips Pan Head Sheet Metal Screw. This screw will
thread into the fastex grommet you installed in step 2 and the bracket
will sit where the cover was (Fig. 5).
6. Line the rectangular hole in the other end of the lightbar bracket, up
with the visor clip and install the visor clip over the lightbar bracket
using the supplied #8 X 1” Sheet Metal Screw (Fig. 3).
7. Make sure all mounting hardware is tightened firmly and repeat
procedure for the passenger side of the vehicle.
Extend the cables and connect to power. Refer to the lightbar manual for
wiring and fusing information.
Fig. 5
ROOF SHEET METAL
SCREW
GROMMET
HEADLINER
VISOR
SWIVEL
BRACKET
LT BAR BRACKET
MOUNTING TAB
Fig. 4
When properly mounted,the rubber sealshouldbeinfull
contact with the vehiclewindshield. The rear of the lightbar
shouldbein contact with the roof. Thisis to prevent light
from entering the passenger compartment. When this has
been achieved,tighten mounting hardware firmly to
maintaincontact.
Mounting
Bracket
ROOF
#8-32 x3/8Torx Hd
Screw (QTY2)
WI
N
DS
H
IE
L
D
RUBBER SEAL
Lightbar
Side View
Lightbar
Side View
Lightbar
Side View
Re-install visor clipover bracket
using supplied #8 X1" sheet metal screw
Install into Faston grommet using
supplied 1/4 X1-1/4" PPHSMS
Install into Faston grommet using
supplied 1/4 X1-1/4" PPHSMS
Install into Faston grommet using
supplied 1/4 X1-1/4" PPHSMS
MOUNTING
BRACKET
Fig. 3
Install Faston grommet
into existing holeinroof
that clipsnapped into.
Fig. 2
DRIVER SIDE DOOR
Pry plastic
cover off
VISOR SWIVEL
BRACKET
WINDSHIELDWINDSHIELD
Remove screw
and visor clip
VISOR
CLIP
MOUNTING CLIP
(remove)
V
I
S
O
R
Fig. 1
WINDSHIELD

Page 4
Fig. 3
REAR VIEW MIRROR
FRONT OF VEHICLE
BOTTOM VIEW
Twist bracket so it sits further from the
windshield on the rear view mirror side.
Passenger Side Shown
Fig. 2
Screw sits
toward top
of slot
Screw sits toward
bottom of slot
REAR VIEW MIRROR
Installation 2019 - 2020 Dodge Ram 1500:
Inner Edge FST
1. Remove the vehicle Visor Clips. The bracket will sit under these
clips after mounting (Fig. 1).
2. Mount the bracket to the light array. Pivot the bracket as shown
so the bracket tilts down on the side nearest the mirror and up on
the road side (Fig. 2). Tighten hardware firmly.
3. Replace the vehicle clip mounting screw near the rear view
mirror with the supplied 8 X 1” Phillips Pan Head Sheet Metal
Screw (Fig. 1). Loosely mount the bracket to the vehicle and
pivot the bracket so the side near the mirror is further from the
windshield (Fig. 3). With the bracket in place tighten the
mounting hardware.

Page 5
SEE NEXT PAGE FOR VEHICLE-SPECIFIC
COMPONENT REQUIREMENTS
BLU GRN YEL ORG RED BRN
TOP SIDE VIEW
BLUGRNYELORGRED
BRN
LED 12
LED 11
LED 10
LED 9
LED 8
LED 7
LED 6
LED 5
LED 4
LED 3
LED 2
LED 1
4
5
J6
231
PINOUT J6
1 - RED - +12VDC
2 - BLACK - GND
3 - GREY - CAN L
4 - GREEN - CAN H
5 - SHIELD - SHIELD
BA DC
DRIVER PASSENGER
0.50"
ABCD
J6
DRIVER PASS
C
D
B
A
ABCD
PART NUMBER KEY
01-0688590-__
YEAR/MAKE
TAURUS/INTERCEPTOR1 - 17 -
EXPLORER/SUV INTERCEPTOR2 - 17 -
F-SERIES3 - 17 -
CHARGER4- 19 -
TAHOE/SUBURBAN/ALL PICKUPS5 - 17 -
FUSION6 - 17 -
RAM 15007 - 17 -
EXPEDITION8 - 18 -
DURANGO9 - 18 -
SILVERADOA - 19 -
EXPLORER/SUV INTERCEPTORB - 20 -
RAM 1500C - 19 -
VERSION
1 - PASS ONLY W TD
PASS ONLY W/O TD2 -
DRVR/PASS W TD3 -
DRVR/PASS W/O TD4-
PASSENGER
DRIVER
8
121
14
7
11 12
13 14
15
21
10
13
9
9
TRIM DETAIL
16
21
42
5
6
22
21
1
3
DIP switch
settings
1 - ON 2 - OFF
TEXTURED SIDE
FACES INWARD
19 20
01-06885900_1
INNER EDGE FST SOLO/DUO, WCX, PASS ONLY W/TD
01-06885900_2
INNER EDGE FST SOLO/DUO, WCX, PASS ONLY W/O TD
01-06885900_3
INNER EDGE FST SOLO/DUO, WCX, DRVR/PASS W/TD
01-06885900_4
INNER EDGE FST SOLO/DUO, WCX, DRVR/PASS W/O TD
02-016J531-00
PCB CONTROL BD 24 OUTPUT INNER EDGE WeCanX SMT
1111
46-0788264-00
HARNESS "C" INNER EDGE FST/RST
1111
46-0788625-01
HARNESS "D" WeCanX INNER EDGE FST/RST
1111
46-0788625-00
HARNESS "A"/"B" WeCanX INNER EDGE FST
11
39-1M18534-05
HOUSING, PLUG 5 POS SL-156 W/LOCKING RAMP, LID
1111
46-0746909-00
ASSY, CABLE INPUT 4/C 20' SL-156
1111
14-040115-04D
SCREW, 4-40 X 1/4 PFHMS TAPTITE, BLACK OXIDE
A/RA/RA/RA/R
14-040216-041
SCREW, 4-40 X 1/4 PPHMS SEMS W/IT LOCK WASHER, SS
4444
14-0050508B26
SCREW, 6-32 X 1/4 PFHMS C'SUNK
44
88
01-026H214-30
SUB ASSY, LTHEAD SOLO WHITE INNER EDGE FST
12
A/RA/RA/RA/R 01-026H214-_0
SUB ASSY, LTHEAD SOLO INNER EDGE FST
5
610
12
A/RA/R
68-196H348-30
LENS, CLEAR OPTIC PLATE INNER EDGE FST
A/RA/RA/RA/R
09-0647873-__
PANEL, GRAPHIC INNER EDGE
1122
01-026H702-__
SUB ASSY, LIGHTED SIGN DUO INNER EDGE FST
1111
38-0546827-20
TRIM, SEAL HOUSING/WINDSHIELD 20" LENGTH INNER EDGE FST
1111
1111
10-0348192-__
LABEL, PN/MN INNER EDGE WeCanX FST
22
55
10-056E563-30
LABEL, WHELEN LOGO GREY 2.75"
1111
26-0215001-06
21-11101610-0
GROMMET, 5/16 ID X 1/2 HOLE
10-056J509-31
LABEL, WeCanX LOGO DARK GREY 3.00"
TY WRAP 6” BLK
A/RA/RA/RA/R 01-026H214-__
SUB ASSY, LTHEAD DUO INNER EDGE FST
2
3
ITEM PART NUMBER DESCRIPTION
QTY QTY QTY QTY
11
12
13
14
15
16
18
19
20
4
5
6
7
8
9
10
1
21
22

Page 6
SEE NEXT PAGE FOR VEHICLE-SPECIFIC
COMPONENT REQUIREMENTS
BLU GRN YEL ORG RED BRN
TOP SIDE VIEW
BLUGRNYELORGRED
BRN
LED 12
LED 11
LED 10
LED 9
LED 8
LED 7
LED 6
LED 5
LED 4
LED 3
LED 2
LED 1
4
5
J6
231
PINOUT J6
1 - RED - +12VDC
2 - BLACK - GND
3 - GREY - CAN L
4 - GREEN - CAN H
5 - SHIELD - SHIELD
BA
D C
DRIVER PASSENGER
0.50"
ABCD
J6
DRIVER PASS
C
D
B
A
ABCD
PART NUMBER KEY
01-0688590-__
YEAR/MAKE
TAURUS/INTERCEPTOR1 - 17 -
EXPLORER/SUV INTERCEPTOR2 - 17 -
F-SERIES3 - 17 -
CHARGER4- 19 -
TAHOE/SUBURBAN/ALL PICKUPS5 - 17 -
FUSION6 - 17 -
RAM 15007 - 17 -
EXPEDITION8 - 18 -
DURANGO9 - 18 -
SILVERADOA - 19 -
EXPLORER/SUV INTERCEPTORB - 20 -
RAM 1500C - 19 -
VERSION
1 - PASS ONLY W TD
PASS ONLY W/O TD2 -
DRVR/PASS W TD3 -
DRVR/PASS W/O TD4-
PASSENGER
DRIVER
8
120
13
7
11 12
13 14
20
10
12
9
9
TRIM DETAIL
15
20
42
5
6
21
20
1
3
DIP switch
settings
1 - ON 2 - OFF
TEXTURED SIDE
FACES INWARD
01-0688590-_1
INNER EDGE FST TRIO, WCX, PASS ONLY W/TD
01-0688590-_2
INNER EDGE FST TRIO, WCX, PASS ONLY W/O TD
01-0688590-_3
INNER EDGE FST TRIO, WCX, DRVR/PASS W/TD
01-0688590-_4
INNER EDGE FST TRIO, WCX, DRVR/PASS W/O TD
02-016J197-00
PCB CONTROL BD 36 OUTPUT INNER EDGE WeCanX SMT
1111
46-0788264-00
HARNESS "C" INNER EDGE FST/RST
1111
46-0788625-01
HARNESS "D" WeCanX INNER EDGE FST/RST
1111
46-0788625-00
HARNESS "A"/"B" WeCanX INNER EDGE FST
11
39-1M18534-05
HOUSING, PLUG 5 POS SL-156 W/LOCKING RAMP, LID
1111
46-0746909-00
CABLE INPUT 4/C 20' SL-156
1111
14-040115-04D
SCREW, 4-40 X 1/4 PFHMS TAPTITE, BLACK OXIDE
A/RA/RA/RA/R
14-040216-041
SCREW, 4-40 X 1/4 PPHMS SEMS W/IT LOCK WASHER, SS
4444
14-0050508B26
SCREW, 6-32 X 1/4 PFHMS C'SUNK
44
88
01-026H214-30
SUB ASSY, LTHEAD SOLO WHITE INNER EDGE FST
12
A/RA/RA/RA/R
5
610
12
01-026H214___
SUB ASSY, LTHEAD TRIO INNER EDGE FST
A/RA/R
68-196H348-30
LENS, CLEAR OPTIC PLATE INNER EDGE FST
A/RA/RA/RA/R
09-0647873-__
PANEL, GRAPHIC INNER EDGE
1122
01-026H702___
SUB ASSY, LIGHTED SIGN TRIO INNER EDGE FST
1111
38-0546827-20
TRIM, SEAL HOUSING/WINDSHIELD 20" LENGTH INNER EDGE FST
1111
1111
10-0348192-__
LABEL, PN/MN INNER EDGE WeCanX FST
22
55
10-056E563-30
LABEL, WHELEN LOGO GREY 2.75"
1111
26-0215001-06
TY WRAP, 6" BLACK
21-11101610-0
GROMMET, 5/16 ID X 1/2 HOLE
10-056J509-31
LABEL, WeCanX LOGO DARK GREY 3.00"
2
3
ITEM PART NUMBER DESCRIPTION
QTY QTY QTY QTY
11
12
13
14
15
17
18
19
20
4
5
6
7
8
9
10
1
21
19 20

Page 7
DODGE
01-0688590_9_
01-0688590_9_
11-36J015-007
11-26J016-007
07-288479-023
07-288479-123
11-26J016-107
11-36J015-107
BASE,HOUSING DRVR DURANGO INNER EDGE FST
BASE,HOUSING PASS DURANGO INNER EDGE FST
COVER, TOP PASS DURANGO INNER EDGE FST
COVER, TOP DRVR DURANGO INNER EDGE FST
BRACKET,VISOR MT PASS DURANGO INNER EDGE FST
BRACKET,VISOR MT DRVR DURANGO INNER EDGE FST
2018 - DURANGO
36
1
1
1
11
1
1
1
1
FINAL, INNER EDGE FST PASS ONLY
FINAL, INNER EDGE FST DRVR/PASS
14-08228C-06D
SCREW, 8-32 X 3/8" PAN TORX HD ROLOK SS BLACK OXIDE
B
C
ITEM PART NUMBER DESCRIPTION
QTY QTY
D
E
F
G
A
01-0688590_7_
01-0688590_7_
11-36H509-107
11-26H508-107
07-288367-023
07-288367-123
11-26H508-007
11-36H509-007
BASE, HOUSING PASS INNER-EDGE 17 RAM 1500 BLK
BASE, HOUSING DRVR INNER-EDGE 17 RAM 1500 BLK
COVER, TOP DRVR INNER-EDGE 17 RAM 1500 BLK
COVER, TOP PASS INNER-EDGE 17 RAM 1500 BLK
BRACKET, VISOR MT PASS 17 RAM 1500 INNER EDGE BLK
BRACKET, VISOR MT DRVR 17 RAM 1500 INNER EDGE BLK
2017 - RAM 1500
36
1
1
1
11
1
1
1
1
FINAL, INNER EDGE FST PASS ONLY
FINAL, INNER EDGE FST DRVR/PASS
14-08228C-06D
SCREW, 8-32 X 3/8" PAN TORX HD ROLOK SS BLACK OXIDE
B
C
ITEM PART NUMBER DESCRIPTION
QTY QTY
D
E
F
G
A
01-0688590_4_
01-0688590_4_
11-36J388-007
11-26J389-007
07-288598-023
07-288598-123
11-26J389-107
11-36J388-107
BASE, HOUSING DRVR CHARGER 16-19 INNER EDGE FST
BASE, HOUSING PASS CHARGER 16-19 INNER EDGE FST
COVER, TOP PASS 16-19 CHARGER INNER EDGE FST
COVER, TOP DRVR 16-19 CHARGER INNER EDGE FST
BRACKET, VISOR MT PASS CHARGER 16-19 INNER EDGE FST
BRACKET, VISOR MT DRVR CHARGER 16-19 INNER EDGE FST
2019 - CHARGER
2
4
1
1
1
11
1
1
1
1
FINAL, INNER EDGE FST PASS ONLY
FINAL, INNER EDGE FST DRVR/PASS
14-08228C-06D
SCREW, 8-32 X 3/8" PAN TORX HD ROLOK SS BLACK OXIDE
B
C
ITEM PART NUMBER DESCRIPTION
QTY QTY
D
E
F
G
A
CHEVROLET
01-0688590_5_
01-0688590_5_
11-36H227-007
11-26H226-007
07-288336-023
07-288336-123
11-26H226-107
11-36H227-107
1
1
1
11
1
1
1
1
BASE, HOUSING DRVR INNER-EDGE 17 TAHOE BLK
BASE, HOUSING PASS INNER-EDGE 17 TAHOE BLK
COVER, TOP PASS INNER-EDGE 17 TAHOE BLK
COVER, TOP DRVR INNER-EDGE 17 TAHOE BLK
BRACKET, VISOR MT PASS 17 SILVERADO/TAHOE INNER EDGE BLK
BRACKET, VISOR MT DRVR 17 SILVERADO/TAHOE INNER EDGE BLK
2017 - TAHOE/SILVERADO
36
FINAL, INNER EDGE FST PASS ONLY
FINAL, INNER EDGE FST DRVR/PASS
14-08228C-06D
SCREW, 8-32 X 3/8" PAN TORX HD ROLOK SS BLACK OXIDE
12 20-006J281-00
SPACER, HEADLINER CHEVY INNER EDGE
B
C
ITEM PART NUMBER DESCRIPTION
QTY QTY
D
E
F
G
H
A
01-0688590_A_
01-0688590_A_
11-36J263-007
11-26J264-007
07-288557-023
07-288557-123
11-26J264-107
11-36J263-107
1
1
1
11
1
1
1
1
BASE, HOUSING DRVR INNER-EDGE 19 SILVERADO BLK
BASE, HOUSING PASS INNER-EDGE 19 SILVERADO BLK
COVER, TOP PASS INNER-EDGE 19 SILVERADO BLK
COVER, TOP DRVR INNER-EDGE 19 SILVERADO BLK
BRACKET, VISOR MT PASS 19 SILVERADO INNER EDGE BLK
BRACKET, VISOR MT DRVR 19 SILVERADO INNER EDGE BLK
2019 - SILVERADO
36
FINAL, INNER EDGE FST PASS ONLY
FINAL, INNER EDGE FST DRVR/PASS
14-08228C-06D
SCREW, 8-32 X 3/8" PAN TORX HD ROLOK SS BLACK OXIDE
12 20-006J281-00
SPACER, HEADLINER CHEVY INNER EDGE
B
C
ITEM PART NUMBER DESCRIPTION
QTY QTY
D
E
F
G
H
A
FORD
01-0688590_1_
01-0688590_1_
11-36H225-007
11-26H224-007
07-288265-023
07-288265-123
11-26H224-107
11-36H225-107
BASE, HOUSING DRVR INNER-EDGE 17 TAURUS BLK
BASE, HOUSING PASS INNER-EDGE 17 TAURUS BLK
COVER, TOP PASS INNER-EDGE 17 TAURUS BLK
COVER, TOP DRVR INNER-EDGE 17 TAURUS BLK
BRACKET, VISOR MT PASS 17 TAURUS INNER EDGE BLK
BRACKET, VISOR MT DRVR 17 TAURUS INNER EDGE BLK
2017 - TAURUS/INTERCEPTOR
FINAL, INNER EDGE FST PASS ONLY
FINAL, INNER EDGE FST DRVR/PASS
14-08228C-06D
36
SCREW, 8-32 X 3/8" PAN TORX HD ROLOK SS BLACK OXIDE
1
-
1
-
1
11
1
1
1
-
1
B
C
ITEM PART NUMBER DESCRIPTION
QTY QTY
D
E
F
G
A
01-0688590_2_
01-0688590_2_
11-36H170-007
11-26H169-007
07-288245-023
07-288245-123
11-26H169-107
11-36H170-107
BASE, HOUSING DRVR INNER-EDGE 15 EXPLORER BLK
BASE, HOUSING PASS INNER-EDGE 15 EXPLORER BLK
COVER, TOP PASS INNER-EDGE 15 EXPLORER BLK
BRACKET, VISOR MT PASS 15 EXPLORER INNER EDGE BLK
COVER, TOP DRVR INNER-EDGE 15 EXPLORER BLK
BRACKET, VISOR MT DRVR 15 EXPLORER INNER EDGE BLK
2017 - EXPLORER
36
1
-
1
-
1
11
1
1
1
-
1
FINAL, INNER EDGE FST PASS ONLY
FINAL, INNER EDGE FST DRVR/PASS
14-08228C-06D
SCREW, 8-32 X 3/8" PAN TORX HD ROLOK SS BLACK OXIDE
B
C
ITEM PART NUMBER DESCRIPTION
QTY QTY
D
E
F
G
A
01-0688590_3_
01-0688590_3_
11-36H385-007
11-26H384-007
07-288328-023
07-288328-123
11-26H384-107
11-36H385-107
BASE,HOUSING DRVR '17 F-SERIES INNER EDGE FST
BASE,HOUSING PASS '17 F-SERIES INNER EDGE FST
COVER, TOP PASS 2017 F-SERIES INNER EDGE FST
COVER, TOP DRVR 2017 F-SERIES INNER EDGE FST
BRACKET,VISOR MT PASS F-SERIES 2017 INNER EDGE FST
BRACKET,VISOR MT DRVR F-SERIES 2017 INNER EDGE FST
2017 - F-SERIES
36
1
1
1
11
1
1
1
1
FINAL, INNER EDGE FST PASS ONLY
FINAL, INNER EDGE FST DRVR/PASS
14-08228C-06D
SCREW, 8-32 X 3/8" PAN TORX HD ROLOK SS BLACK OXIDE
B
C
ITEM PART NUMBER DESCRIPTION
QTY QTY
D
E
F
G
A
01-0688590_8_
01-0688590_8_
11-36H806-007
11-26H807-007
07-288437-023
07-288437-123
11-26H807-107
11-36H806-107
BASE, HOUSING DRVR '17 EXPEDITION INNER EDGE FST
BASE, HOUSING PASS '18 EXPEDTION INNER EDGE FST
COVER, TOP PASS '17 EXPEDITION INNER EDGE FST
COVER, TOP DRIVER '17 EXPEDITION INNER EDGE FST
BRACKET, VISOR MT '17 EXPEDITION PASS INNER EDGE FST
BRACKET, VISOR MT '17 EXPEDITION DRVR INNER EDGE FST
2018 - EXPEDITION
36
1
1
1
11
1
1
1
-
1
FINAL, INNER EDGE FST PASS ONLY
FINAL, INNER EDGE FST DRVR/PASS
14-08228C-06D
SCREW, 8-32 X 3/8" PAN TORX HD ROLOK SS BLACK OXIDE
B
C
ITEM PART NUMBER DESCRIPTION
QTY QTY
D
E
F
G
A
2020 - EXPLORER
01-0688590_B_
01-0688590_B_
11-36J433-007
11-26J434-007
07-288612-023
07-288612-123
11-26J434-107
11-36J433-107
BASE, HOUSING DRVR 2020 UTILITY INNER EDGE FST
BASE, HOUSING PASS 2020 UTILITY INNER EDGE FST
COVER, TOP PASS 2020 UTILITY INNER EDGE FST
BRACKET, VISOR MT PASS '20 UTILITY INNER EDGE FST
COVER, TOP DRVR 2020 UTILITY INNER EDGE FST
BRACKET, VISOR MT DRVR '20 UTILITY INNER EDGE FST
2
4
1
1
1
11
1
1
1
1
FINAL, INNER EDGE FST PASS ONLY
FINAL, INNER EDGE FST DRVR/PASS
14-08228C-06D
SCREW, 8-32 X 3/8" PAN TORX HD ROLOK SS BLACK OXIDE
B
C
ITEM PART NUMBER DESCRIPTION
QTY QTY
D
E
F
G
A
01-0688590_6_
01-0688590_6_
11-36H324-007
11-26H323-007
07-288302-023
07-288302-123
11-26H323-107
11-36H324-107
BASE, HOUSING DRVR '17 FUSION INNER EDGE FST
BASE, HOUSING PASS '17 FUSION INNER EDGE FST
COVER, TOP PASS '17 FUSION INNER EDGE FST
COVER, TOP DRIVER '17 FUSION INNER EDGE FST
BRACKET, VISOR MT '17 FUSION PASS INNER EDGE FST
BRACKET, VISOR MT '17 FUSION DRVR INNER EDGE FST
2017 - FUSION
36
1
1
1
11
1
1
1
1
FINAL, INNER EDGE FST PASS ONLY
FINAL, INNER EDGE FST DRVR/PASS
14-08228C-06D
SCREW, 8-32 X 3/8" PAN TORX HD ROLOK SS BLACK OXIDE
12 15-081416-160
SCREW, 8 X 1 PPHSMS
12 15-131416-202
SCREW, 1/4 X 1 1/4 PPHSMS SS TYPE A
12 21-12081205-3
SCREW GROMMET,
B
C
ITEM PART NUMBER DESCRIPTION
QTY QTY
D
E
F
G
I
J
K
A
01-0688590_C_
01-0688590_C_
11-36J527-007
11-26J526-007
07-288642-023
07-288642-123
11-26J526-107
11-36J527-107
BASE, HSG DRVR 2019 RAM 1500 BLACK INNER EDGE FST
BASE, HSG PASS 2019 RAM 1500 BLACK INNER EDGE FST
COVER, TOP PASS 2019 RAM 1500 BLACK INNER EDGE FST
COVER, TOP DRVR 2019 RAM 1500 BLACK INNER EDGE FST
BRACKET, VISOR MT PASS BLACK 2019 RAM 1500 INNER EDGE FST
BRACKET, VISOR MT DRVR BLACK 2019 RAM 1500 INNER EDGE FST
36
1
1
1
11
1
1
1
1
FINAL, INNER EDGE FST PASS ONLY
FINAL, INNER EDGE FST DRVR/PASS
14-08228C-06D
SCREW, 8-32 X 3/8" PAN TORX HD ROLOK SS BLACK OXIDE
15-081416-160
SCREW, 8 X 1 PPHSMS
12
2019 - RAM 1500
B
C
ITEM PART NUMBER DESCRIPTION
QTY QTY
D
E
F
G
I
A