WHITECROFT LIGHTING Aerial Industry User manual

TECHNICAL SUPPORT
Telephone: [phone]
E-mail: [email protected]
http://www.whitecroftlighting.com
PRODUCT DATA
Aerial Industry/Sport is a high output, high efficiency high bay luminaire for general applications.
The luminaire is constructed from sheet steel, polycarbonate and acrylic materials.
Aerial Industry/Sport incorporates the latest high efficiency LED light engines and drivers for
optimum efficiency and luminaire life.
The luminaire range includes a Quadraprism(medium beam), Opal diffuser(wide beam), and High
Rack optic to suit most applications. Polycarbonate option for sports application.
Aerial Industry/Sport can be wire suspended or surface / trunking / drop rod mounted by utilizing
one of the optional suspension kits available.
The luminaire is supplied complete with external plug and socket cable terminations for speed
and ease of wiring.
PRODUCT SPECIFICATION
Finish: Body - White high reflective paint
Materials: Body Assembly - Sheet Metal
Rear Backplate - 0.9mm mild steel
Diffuser Options - 2.5mm Quad Prism Acrylic(medium beam)
- 2mm Opal Satine Acrylic(wide beam)
- 3mm Polycarbonate(sport)
- 15 degree lens with clear diffuser(high rack)
End cap - Injection moulded white Polycarbonate.
Control Gear: DALI addressable or Fixed output LED Drivers.
Emergency: 3 hr integral emergency pack (Refer to website for options)
Light Source: 4000k high output LED’s
Op. Temp: -20 to +25 °C (Medium and wide beam)
-20 to +35 °C (High rack and sport)
Minium 0 °C for all emergency options.
Power: Please refer to website for latest Wattage
IP Rating: IP40 front & rear
IK Rating: IK09 for Aerial Sport
Connection: Plug & Socket - 2.5mm2 maximum cable
Suspension: Wire / Trunking / Surface / Drop Rod
Supply: 240V AC, 50Hz
Connection: 1.5mm SQ Panel mount plug & sockets on rear face
IP Rating: IP20
Aerial Industry
Aerial Sport
HIGH BAY LUMINAIRE
INSTALLATION INSTRUCTIONS
PK/LEAFAERIND November 2019 - Rev G
Whitecroft Lighting Limited
Burlington Street, Ashton-under-Lyne, Lancashire OL7 0AX
Telephone [phone] Facsimile: [phone]
Registered No. 3848973 England Registered Office: As above

REMOVE REAR COVER TO ACCESS
BATTERY CONNECTIONS.
DROP ROD & SURFACE
SUSPENSION POINT.
TRUNKING SUSPENSION
POINT.
MAINS CONNECTION PLUG.
DALI CONNECTION PLUG.
COMEPS CONNECTION PLUG.
1340
1430
O21
O8
110
86,75 47,6
1410
1421
310,5
234
OPTIONAL SURFACE MOUNT/TRUNKING/DROP ROD BRACKET.
INSTALLATION INSTRUCTIONS
PRE INSTALLATION
1. Remove the luminaire from packaging and inspect the contents for damage.
2. Ensure that the supporting ceiling structure is of adequate strength to support
the weight of the luminaire. (see table for weights)
WIRE SUSPENSION KIT OPTION - 5m (supplied separate)
1. Loop the suspension cable around a suitable load bearing structure at the
approximate centres indicated. Fit the gripple clutch & suspension toggle
‘Y’splitter to the cable and adjust to the desired height making reference to
the separate suspension kit instructions.
2. Support the weight of the luminaire from below and then offer the ‘Y’ splitter
toggles through the slots indicated on the back of the luminaire at each end.
3. Check luminaire height and level if necessary via the adjustable clutch
mechanisms (Nb support the luminaire weight when adjusting). Trim off any
excess cable only when happy with the luminaire suspension height.
TRUNKING /SURFACE MOUNT KIT OPTION - (supplied separate)
1 Slide the support brackets into the four slots at each end of the luminaire and
secure in place via the two self tapping screws provided.
2 Fit the supplied tee piece plug adaptors to the sockets to enable side entry of
the connection plugs.
3 If suspending from trunking use a suitable 20mm adaptor (not supplied).
4 If suspending via drop rods, use 8mm rod at centres indicated.(not supplied)
5 If surface mounted use suitable fixings at centres indicated.(not supplied)
NB –If the luminaire is being suspended via customer preferred method, eg drop rods or
chains, then a surface mount kit (ABTRU) must be utilized to facilitate fit. (ordered separate).
GENERAL WIRING INFORMATION
1. Wire the plugs in accordance with the schematic detailed below noting location
of Dali and COMEPS sockets. Connect plugs into relevant sockets in the rear
of the luminaire and test for correct operation.
2. If the luminaire is an emergency variant, connect the battery leads and mark
the installation date. Access to batteries can be gained from the rear of the
luminaire by removing the gear cover (4 screws). NB Battery connection must
be undertaken before installation of luminaire if surface or trunking mounted.
3. If fixed output operation is required, installer must fit link cable within Dali plug
‘N’ & ‘L’ terminals as detailed below.(Nb Link not required for Dali operation)
Warning: The LEDs in this luminaire operate at HIGH VOLTAGE.
Ensure that the luminaire is isolated before opening.
GENERAL INFORMATION
1. A qualified electrician, in accordance with IEE wiring regulations, should carry out connection to
mains wiring.
2. This luminaire must be EARTHED.
3. Ensure that the rated luminaire voltage and frequency requirements are compatible with the
available mains supply.
4. Cleaning of lenses should be carried out using a lint free cloth and anti-static cleaning fluid.
5. The luminaire body will become hot under normal operating conditions. Allow to cool before
undertaking any necessary maintenance work.
PRODUCT DIMENSIONS (All dimensions are in ‘mm’.)
Weight Standard 9.8kg
Weight Emergency 10.8kg
For surface and
trunking attachment
use ABTRU