WHITECROFT LIGHTING Florin E3 Series Manual

Please note: All images shown are for illustration purposes and should be used only for reference.
TECHNICAL SUPPORT
Telephone: [phone]
E-mail: [e-mail]
http://www.whitecroftlighting.com
WARNING: TO AVOID INJURY, KEEP
FINGERS CLEAR OF SPRINGS WHEN
REMOVING RECESSED LUMINAIRE
FROM CEILING
For Photometry refer to
www.whitecroftlighting.com
GENERAL INFORMATION
1) A qualified electrician, in accordance with IEE
wiring regulations, should carry out connection to
mains wiring.
2) Ensure that the rated voltage and frequency
requirements are compatible with the available
mains supply.
3) Cleaning of reflectors and lenses should be
carried out using clean, soft and lint free cloths
and anti-static cleaning fluid
4) Do not carry out high voltage insulation test, i.e.
500/1000v this may damage internal components.
SAFETY INFORMATION
The luminaire should be positioned so that
prolonged staring into the luminaire at a distance
closer than 0.24m is not expected.
Specification –FLS31EP/65,
FLS32EP/65,
FLSH31EP/65
Supply Voltage:
230Vac ± 10% 50/60 Hz
Supply Current:
20mA @ 230V ac
Ambient Temperature:
0°C to +35°C
Conductor size:
0.5 –2.5mm²
Mounting Screws:
M4
Weight of Luminaire:
250g (incl. battery)
IP Rating of Luminaire:
IP65
Average Lumen output:
Battery:
260lm
6.4V, 1.5Ah 2 x 18650
LiFePO4cells
Dec 2021 - Rev B
Florin IP65
Installation Leaflet
Whitecroft Lighting Limited
Burlington Street, Ashton-under-Lyne, Lancashire OL7 0AX
Telephone [phone] Facsimile: [phone]
Registered No. 3848973 England Registered Office: As above
Specification –FLS31/CB/65,
FLS32/CB/65,
FLSH31/CB/65
Central Supply Voltage:
93-265V dc/ac
50/60Hz
Central Supply Current:
20mA @ 230V ac
Central supply output current:
670mA
Ambient Temperature:
0°C to +35°C
Conductor size:
0.5 –2.5mm²
Weight of Luminaire:
65g
IP Rating of Luminaire:
IP65
Average output (Lumens)
260 lm

Please note: All images shown are for illustration purposes and should be used only for reference.
General Description
Florin E3 is a range of stand-alone IP65 LED
emergency luminaires incorporating a driver and
battery pack in a plastic housing. The luminaire
contains a high-power white LED and indicator LED
for emergency use only.
The LED control gear has reinforced insulation
between the supply and the battery circuit, and a
battery charger with short circuit protection that will
continue to operate when the short is removed.
Batteries (where applicable)
The luminaire includes a 1.5Ah rechargeable
LiFePO4battery pack for 3 hour operation. When
the luminaire no longer meets the 3 hours duration
the battery should be replaced.
Relevant Standards
EN 61347-2-7 Lamp control gear
EN 61347-2-13 LED control gear
EN 60598-2-22 Luminaire
IMPORTANT:
Please ensure that the information contained in this
leaflet is passed on to the user/maintenance engineer.
Mark the luminaire with the date of commissioning in
the space provided on the battery label.
The battery lead should only be connected at the time
of commissioning.
When the supplies and battery leads are connected,
the white cover should be ‘clicked’ into place to
prevent electric shock.
The LED is non-replaceable. Contact Whitecroft
Lighting in the unlikely event of a failure.
Operation –integrated battery versions
Upon connection of a permanent mains supply the
indicator LED lights to show the battery is receiving
charge. Following an initial charging period,
commissioning test and a subsequent charging period
of 24 hours the unit will be capable of providing 3
hours emergency duration.
Operation –central battery
When power is supplied to the luminaire supply inputs,
the high-power LED will light.
Installation
The luminaire must be installed by a qualified person
in accordance with the current building and wiring
regulations. Luminaires comply with the EMC directive
in both modes of operation, mains and emergency.
The luminaire is designed to be surface mounted onto
a ceiling.
Automatic Commissioning
(FLS31EP/65, FLS32EP/65 & FLSH31EP/65 only)
Please note there is no need to do a manual test on
this product.
If in the unlikely event a manual test needs to be
undertaken please ensure it has completed the
commissioning phase as per the table below.
Do not connect the batteries until there is a reliable
permanent mains supply present as a mains
interruption will rest the commissioning test clock.
The commissioning test will start when the permanent
supply and batteries are connected.
Commissioning phase table
Stage
Hours
Status
LED
Indication
1
upto
24
Battery
charging
Flashing
green
2
3
Discharge test
Flashing
green
3
24
Battery
charging
Flashing
green
4
0
Commissioning
complete
Constant
green
Total
51

Please note: All images shown are for illustration purposes and should be used only for reference.
For best photometric performance ensure that the long axis of the escape route lens is in
line (parallel) with the path of the escape route as shown above.