Whitewood Furniture TV-28 User manual

ITEM NO.: TV-28
REVISED APR 03, 2020
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
WARNING!
Serious or fatal injuries can occur from furniture tip over. Use tip over restraint
(provided) to secure this product to the wall.
Description
Item No.
: 28 IN MISSION TV STAND WITH DRAWER
: TV-28

ITEM NO.: TV-28
REVISED APR 03, 2020
Printed in Vietnam
- 2 -
BEFORE ASSEMBLY
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your product. Protect the surface of the product with cloth if you are using any
product with rubber feet or base.
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: TV-28
REVISED APR 03, 2020
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Top
1
F
Drawer front
1
B
Side frame
(L-R)
2
G
Drawer side
(L-R)
2
C
Shelf
1
H
Drawer back
1
D
Support Rail
1
I
Drawer
bottom
1
E
Back panel
1
NOTE: WARNING LABEL (INCLUDED)

ITEM NO.: TV-28
REVISED APR 03, 2020
Printed in Vietnam
- 4 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Bolt
(M6 x 35mm)
8
9
Medium Pan Head screw
*Metal knob: (M4x22mm)
*Wooden knob: (M4x25mm)
1
2
Spring Washer
(6.5 x 11mm)
8
10
Wooden Knob
(38 x 30mm)
1
3
Flat Washer
(6.5 x 19mm)
8
METAL KNOB
(30 x 30mm)
GOES WITH
FINISHED ITEM
ONLY.
1
4
Allen key
(M4 x 30mm x 110mm)
1
11
Short Pan head screw
(M4 x 15mm)
2
5
L-Bracket
2
12
Long Pan head screw
(M4 x 50mm)
2
6
Short Screw
(M3.5 x 15mm)
4
13
Steel Tip Bracket
4
7
Short Pan Head Screw
(M3.5 x 15mm)
4
14
Flat Nylon Tie
2
8
Long Screw
(M4 x 35mm)
8

ITEM NO.: TV-28
REVISED APR 03, 2020
Printed in Vietnam
- 5 -
STEP 1
Attach shelf (C) and top (A) to side frames (B) with bolts (1), and washers (2) and (3) as shown
below. Tighten with Allen key (4).
Attach supporting bar (D) to side frames (B) with brackets (5) and screws (6) as shown below.
Tighten with a screwdriver.
STEP 2
Slide back panel (E) into the grooves, then attach back panel (E) to the unit with screws (7) as
shown below. Tighten with a screwdriver.

ITEM NO.: TV-28
REVISED APR 03, 2020
Printed in Vietnam
- 6 -
STEP 3
Attach drawer sides (G) to drawer front (F) with screws (8) as shown below. Tighten with a screwdriver.
Slide drawer bottom (I) into grooves of drawer sides (G) and drawer front (F) as shown below.
Attach the drawer back (H) to the drawer sides (G) with screws (8) as shown below. Tighten with a
screwdriver.
STEP 4
Carefully put the drawer into the unit.
Attach knob (10) to front of drawer with pan head screw (9) as shown below. Tighten with a screwdriver.

ITEM NO.: TV-28
REVISED APR 03, 2020
Printed in Vietnam
- 7 -
STEP 5
Attach brackets (13) to the back of the unit with screws (11) through the smaller holes in the brackets as
shown below.
Important!
Properly attach the other brackets (13) to the wall in an area of drywall or plaster with a wood stud:
Mark the attachment point(s) with a pencil at the appropriate height positioned over the wood
stud(s) in the wall.
Place the unit into position so both mounting brackets are vertically in line.
Adjust the levelers to the appropriate height to level the unit.
Properly attach the other brackets (13) to the wall stud with screws (12) through the smaller holes as
shown below.
Lace the end of flat nylon ties (14) through the larger holes in each mounting bracket. Bring both ends
together and slide the flat ends through the locking ends and draw it through until all slack is removed.
Confirm that the strap is securely laced and locked.