Whitewood Furniture SH-3223A User manual

ITEM NO.: SH-3223A
REVISED 30 MAR, 2020
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
WARNING!
Serious or fatal injuries can occur from furniture tip over. Use tip over restraint
(provided) to secure this product to the wall.
Description
Item No.
: 32 X 12 X 36 HIGH BOOK CASE
: SH-3223A

ITEM NO.: SH-3223A
REVISED 30 MAR, 2020
Printed in Vietnam
- 2 -
BEFORE ASSEMBLY
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your product. Protect the surface of the product with cloth if you are using any
product with rubber feet or base.
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: SH-3223A
REVISED 30 MAR, 2020
Printed in Vietnam
- 3 -
PARTS LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Q’ty
Sketch
NO
Description
Q’ty
Sketch
A
Top
1
B
Side panel
(L-R)
2
C
Bottom panel
1
D
Adjustable shelf
2
E
Back
panel
1
F
Connecter
2

ITEM NO.: SH-3223A
REVISED 30 MAR, 2020
Printed in Vietnam
- 4 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Q’ty
Sketch
NO
Description
Q’ty
Sketch
1
Bolt
(M6 x 30mm)
8
2
Flat Washer
(6.5 x13mm)
8
3
Lock Washer
(6.5 x11mm)
8
4
Allen key
(M4 x 30mm x 110mm)
1
5
Shelf support bracket
8
6
Short Screw
(M3.5 x 15mm)
8
7
Short Pan head
screw
(M4 x 15mm)
2
8
Steel Tip Bracket
4
9
Medium Pan head
screw
(M4 x 20mm)
7
10
Flat Nylon Tie
2
11
Long Pan head
screw
(M4 x 50mm)
2

ITEM NO.: SH-3223A
REVISED 30 MAR, 2020
Printed in Vietnam
- 5 -
STEP 1
Attach top (A) and bottom panel (C) to side panels (B) with bolts (1), and washers (2) and (3) as
shown below. Tighten with Allen key (4).
STEP 2
Slide back panels (E) into the grooves as shown below.
Remove the paper strip and attach sticky side of the connecters (F) to the back of the unit. Then
attach connecter (F) to the top (A) and bottom panel (C) with screws (9) as show below. Tighten
with a screwdriver.

ITEM NO.: SH-3223A
REVISED 30 MAR, 2020
Printed in Vietnam
- 6 -
STEP 3
Attach brackets (5) to the unit as shown below. Then place the shelves (D) on the brackets and
attach with screws (6). Tighten with the screwdriver.
Attach brackets (8) to the back of the unit with screws (7) through the smaller holes in the brackets as
shown below.
Important!
Properly attach the other brackets (8) to the wall in an area of drywall or plaster with a wood stud:
Mark the attachment point(s) with a pencil at the appropriate height positioned over the wood
stud(s) in the wall.
Place the unit into position so both mounting brackets are vertically in line.
Properly attach the other brackets (8) to the wall stud with screws (11) through the smaller holes as shown
below.
Lace the end of flat nylon ties (10) through the larger holes in each mounting bracket. Bring both ends
together and slide the flat ends through the locking ends and draw it through until all slack is removed.
Confirm that the strap is securely laced and locked.