Whitewood Furniture TV-36 User manual

ITEM NO.: TV-36
REVISED JAN 10, 2015
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: MISSION ENTERTAINMENT STAND
: TV-36

ITEM NO.: TV-36
REVISED JAN 10, 2015
Printed in Vietnam
- 2 -
BEFORE ASSEMBLY
Thank you for purchasing this quality product. This product has been designed for easy assembly and
constructed for durability. All parts were checked prior to packaging to insure quality. Prior to beginning
assembly, however, make sure all parts and hardware are included and free of obvious defect. If a part is
missing or defective, please contact the store where purchased. If hardware is missing, or you need help with
assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from
being scratched.
-Remove all wrapping material, including staples & packing straps before you start to assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the finish of your
product. Protect the surface of the product with cloth if you are using any product with rubber feet or
base.
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: TV-36
REVISED JAN 10, 2015
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO Description Qty Sketch NO Description Qty Sketch
A TOP 1
B SHELF 1
C BOTTOM
SHELF 1 D
SIDE FRAME
(L&R) 2
E
DRAWER
BOTTOM
PANEL
1
F
BOTTOM
SUPPORT
RAIL
1
G
BACK
PANEL 1 H
DRAWER
FRONT
(L&R)
1
I
DRAWER
BACK
PANEL
1
J
DRAWER
SIDE PANEL
(L&R)
2
K
DRAWER -
SUPPORT
BAR
1

ITEM NO.: TV-36
REVISED JAN 10, 2015
Printed in Vietnam
- 4 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
No Description Qty Sketch No Description Qty Sketch
1 BOLT
(M6x35mm) 8
2 FLAT WASHER
(6.5x19mm) 8
3
SPRING
WASHER
(6.5x11mm)
8
4 LONG SCREW
(M4x30mm) 11
5 SHORT SCREW
(M3.5x15mm)
6
6 SHELF
SUPPORT PIN 4
7
CAMBOLT 2 8
CAMLOCK
2
9
KNOB 2
10
PAN HEAD
SCREW
(M3.5x35mm)
2
11
STEEL BAND 1
12 Warning label 1
13 ALLEN KEY
(4x80mm) 1

ITEM NO.: TV-36
REVISED JAN 10, 2015
Printed in Vietnam
- 5 -
Attach the Cambolt (7) to the side frames (D) as shown below. Tighten with a screwdriver.
STEP 2
Attach the support rail (F) to the side frames (D) with the camlock (8). Tighten with Allen key (13).
STEP 1

ITEM NO.: TV-36
REVISED JAN 10, 2015
Printed in Vietnam
- 6 -
Attach the bottom self (C) to the side frames (D) with bolts (1), and washers (2) and (3). Tighten with
Allen key (13).
Slide the back panel (G) into the grooves as shown below.
STEP 4
Attach the bottom self (C) to the side frames (D) with bolts (1), and washers (2) and (3). Tighten with
Allen key (13).
Attach the support rail (F) to the side frames (D) with the camlock (8). Tighten with Allen key (13).
STEP 3

ITEM NO.: TV-36
REVISED JAN 10, 2015
Printed in Vietnam
- 7 -
Attach Top (A) to the unit with bolts (1), and washers (2) and (3) as shown below. Tighten with Allen
key (13).
STEP 6
Insert shelf support pins (6) into the side frames (D). Place the shelf (B) on the shelf support pin and
attach with screws (5) as shown below. Tighten with a screwdriver.
STEP 5

ITEM NO.: TV-36
REVISED JAN 10, 2015
Printed in Vietnam
- 8 -
STEP 7
Attach drawer sides (J) to the drawer front (H) with screws (4) as shown below. Tighten with a
screwdriver.
STEP 8
Slide the drawer bottom panel (E) into the grooves as shown below.

ITEM NO.: TV-36
REVISED JAN 10, 2015
Printed in Vietnam
- 9 -
STEP 9
Attach the drawer back panel (I) to the drawer (from step 8) with screws (4) as shown below. Tighten
with a screwdriver.
STEP 10
Attach the drawer support bar (K) underneath the drawer with screws (4) as shown below. Tighten
with a screwdriver.

ITEM NO.: TV-36
REVISED JAN 10, 2015
Printed in Vietnam
- 10 -
STEP 11
Attach the knobs (9) to the drawer front with screws (10). Tighten with a screwdriver.
STEP 12
Insert the drawer into the unit. Stick the warning label (12) into the drawer before use.
Attach steel bands (11) to the unit with screws (5). Then attach the steel band to a wall with screw (4)
as shown below (to secure the product and prevent tipping). Tighten with a screwdriver.