Whittier Wood 1119RGB User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 12/17
Model #
1119RGB
Stonewood
Upholstered
Bench
RGB = Rustic Glazed Brown finish
Assembly Instructions
IMPORTANT NOTES:
•For normal household use only. Not recommended for commercial use.
•Do not climb or stand on or in this piece of furniture.
•This assembly requires two people.
WARNING
Drilling, sawing, sanding or machining wood products can expose you to
wood dust, a substance known to the state of California to cause cancer.
Avoid inhaling wood dust or use a dust mask
or other safeguards for
personal protection.
For more information go to: www.p65warnings.ca.gov/wood
This product can expose you to chemicals, including formaldehyde,
which are known to the State of California to cause cancer.
For more information go to: www.p65warnings.ca.gov/furniture
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CUSTOMER SERVICE
If you ever have questions about your furniture, please do not hesitate to contact us. In the unlikely event you need a
replacement part; we can make those parts available through an authorized Whittier Wood Furniture dealer. If you
cannot order replacement parts through your dealer, please contact our customer service department.
Hours: Our friendly customer service staff can be reached:
Monday-Friday 8:00 a.m. to 5:00 p.m. (Pacific Time).
You may leave a message 24 hours a day, seven days a week.
Customer Service: 800-653-3336 • Outside the U.S.: 541-687-0213
Fax: [phone]• Email: [email protected]
Thank you for allowing us to help you furnish your
home. We are certain you will be delighted with
your new furniture for many years to come.

1119RGB Stonewood Upholstered Bench
Parts List
1119RGB — Page 2 — 12/17
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter(s) and part name.
Part
Description
Quantity
A
Top Assembly
1
B
Upholstered Seat (attached)
1
C
Shelf Assembly
1
D
Shelf Support (attached)
2
E
Front Leg
2
F
Left Back Leg
1
G
Right Back Leg
1
H
#6 x 1/2" Undercut Screw AB (inserted)
20
I
#8 x 1-1/4" Pan Head Screw
30
(26 inserted)
J
5/16" Flat Washer
4
K
3/8" x 1" Insert Nut (inserted)
4
L
3/8" x 2-1/2" Hex Bolt
4
M
1/4" x 20mm Insert Nut (inserted)
4
N
Adjustable Glide (installed in Legs)
4
O
90
o
Bracket (2 holes)
10

1119RGB Stonewood Upholstered Bench
Assembly Instructions
1119RGB — Page 3 — 12/17
Tool Required: Phillips Screwdriver, 9/16" or Adjustable Wrench, Mallet or Padded Hammer.
1. Place the Top Assembly (A) upside-down on a clean, protected surface. Position the Front
Legs (E) at the corners of the Top Assembly (A). Insert the 3/8" x 2-1/2" Hex Bolts (L) with the
Washers (J) through the corner brace into the Legs and securely fasten. See Figure 1a.
2. Align the Pocket holes in the front corners of the Shelf Assembly (C) with the notches in the
front legs and insert the shelf into the notches. Align the notch in the Right Back Leg (G) with the
pocket hole in the Shelf Assembly and the Corner Bracket of the Top Assembly and secure the
leg using a 3/8" x 2-1/2" Hex Bolt (L) and Washer (J) repeat using the Left Back Leg (F).
See Figures 2 and 2a.
Fig. 1a
J
L
x 2
x 2
E
A
Fig. 1
J
L
Fig. 2
C
F
A
I
J
L
x 2
x 2
G
K
Fig. 2a

1119RGB Stonewood Upholstered Bench
Assembly Instructions
1119RGB — Page 4 — 12/17
3. Using the pocket holes as guides, secure the Shelf Assembly (C) to the Legs with four
#8 x 1-1/4" Pan Head Screws (I). See Figures 3 and 3a.
4. Turn the bench upright.
Place the bench at its final destination. Rotate the Adjustable Glides (N) on the bottoms of the
legs until the unit is level. See Figure 4.
N
Fig. 4
N
Fig. 3
I
x 4
I
Fig. 3a