Wildridge Classic LCC-207 User manual

ASSEMBLY INSTRUCTIONS
ClassiC mission glider
330-893-4212 • www.wildridge.com
LCC207
© 2018
Step 1
Position seat (B) and
back (A) and fasten
outside supports with
(4) 2" bolts & ange
nuts on both sides as
shown above.
Use the 1/2" x 1 1/2"
x 5" connector block
(F) provided to fasten
center seat support to
the back using
(4)1 1/4" screws, as
shown on right.
Required Tools:
- Mallet/Non Marring Hammer
(Do not use Metal Headed Hammer)
- Cordless Drill
- #2 Square Drive bit
- 9/16” and 7/16”Wrench or Socket
Hardware:
- (4) 1/4” x 2” Bolts
- (2) 1/4” x 4” Bolts
- (2) 1/4” x 3 1/2” Bolts
- (8) 1/4” Flange Nuts
- (4) Glider Hangers
- (8) 3/8” x 2 1/2” Bolts
- (16) 3/8”Washers
- (8) 3/8” Locknuts
- (4) 1 1/4” Screws
- (8) 3” Screws
Parts:
A = (1) Back
B = (1) Seat
C = (2) Arm-Leg Assembly
D = (2) Glider Base Assembly
E = (2) Base Support
F = (1) Connector Block
Step 2
Position the right arm-leg assembly (C) in position as shown
and attach it to the seat/back assembly using a 4" bolt & a
ange nut in the back and a 3 1/2" bolt & ange nut in the
front. Repeat with the left arm-leg assembly.
A
B
CC
DD
E
F
A
C
Fasten Outside
Supports On
Both Sides
B
B
F
A
Connector
Block (F)
Will Go
Here
4” Bolt &
Flange Nut
3 1/2”
Bolt &
Flange
Nut

ASSEMBLY INSTRUCTIONS
ClassiC mission glider
330-893-4212 • www.wildridge.com
LCC207
© 2018
Step 3
Position both of
the glider base
assemblies (D), on
a at surface, as
shown.
Attach both the
base supports (E) as
shown, keeping the
base supports 1/8”
in from the side (see
inset) and fasten together with (8) 3" screws through counter
sink holes provided.
Step 4
Now mount (1) glider hanger onto
base as shown, using (1) 3/8" x
2 1/2" bolt with (2) 3/8" washers.
First slide a washer on bolt and push
through hole provided from inside to
outside. Add another washer then
hang the glider hanger on bolt with
curve away from bottom of base as
shown. Now fasten with (1) 3/8"
locknut tightly on bolt. Repeat other
3 sides.
Step 6
Your bench is now complete.
Thank you for purchasing from Wildridge.
Step 5
Set the seat assembly over
the base and fasten bottom
of glider hangers to leg
assembly (Note: For the
base piece - make sure
the angled section goes
towards the
back of chair and
straight section
goes towards
the front of
chair, see inset
below) and attach
with (1) 2 1/2”
bolt, washers and
locknuts, repeat on
other 3 sides.
DEE
D
D
E
Keep Base
Support
1/8” In
From Side
This
Straight
Piece
Goes
Towards
Front
This
Angled
Piece
Goes
Towards
Back