Wilson Electronics 301201 User manual

Antenna
Installation
Guide
Features:
• High-gain
• Weather resistant
• Built-in ground plane
• Slim and unobtrusive
• Mounting bracket included
• Installs Easily
• For fixed installations
Multi-Band
Omni-Directional
Antenna
PART# 301201 - 75 ohm
PART# 301202 - 50 ohm

1Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected]. Hours: 7 am to 6 pm MST.
2
Antenna Adapter
An 18-inch external adapter is required to connect the cell phone or cellular data card
directly to the antenna. The external adapter is cell phone/data card specific and may be
purchased through a local retailer. Refer to Wilson Electronics Adapter Guide to identify
the right adapter for your cell phone or cellular data card. The Adapter Guide is available
through a local retailer. It is also available on our web site, www.WilsonElectronics.com,
or you may call Technical Support at 866-294-1660.
Package Contents
1 – Multi-Band Omni-Directional Antenna 6 – Radials (3 short, 3 long)
1 – L-Bracket 4 – 10x1 Phillips round screws
1 – U-bolt assembly 1 – Thread-locker liquid
1 - N Female - FME Male Connector (2F1108)
(Provided only with 301202 Antenna)
Determine Your Mounting Location
The antenna should be mounted high on the building with no obstructions. There is a
compromise between installing the antenna as high as possible and keeping the cable
run short to reduce signal loss. (The longer your cable, the greater the signal loss will
be.) For cable runs under 20 feet (recommended), Wilson Electronics offers various RG-
58 cable lengths and connectors (sold separately). If a cable length greater than 20 feet
is needed, we recommend increasing the cable size to Wilson 400 cable to minimize
signal loss.
Make sure your mounting location is as far away as possible from other antennas and
upright objects such as flagpoles. Be careful not to kink or crush the antenna cable or
bend it tightly during installation. This can lead to poor performance and signal loss. It
is important to mount the antenna vertically; mounting horizontally or at an angle will
significantly degrade performance.
How It Works
Wilson Electronics Dual-Band Omni-Directional Antenna will collect the cell tower signal
and send it through the cable to a Signal Booster or directly to the cell phone or cellular
data card. When the cell phone or cellular data card transmits, the signal is transferred to
a Signal Booster or directly to the antenna and broadcasted back to the cell tower.
Thank you for purchasing a Wilson Electronics Antenna
Please read all instructions before installing your antenna, and check the parts supplied
against those listed in this guide. Wilson Electronics weatherproof, fiberglass-encased
antenna is omni-directional and ideal for many exterior building locations, such as homes,
offices, stores and warehouses.
Our innovative design results in high efficiency and low signal loss, which means more
signal to your cell phone or cellular data card. This multi-band, high-performance, omni-
directional antenna supports multiple frequencies (Specifications are on the back page). It
is backed by Wilson Electronics 30-day money-back guarantee and 1-year limited warranty.

1
2
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected]. Hours: 7 am to 6 pm MST.
Disclaimer: The information provided by Wilson Electronics, Inc. is believed
to be complete and accurate. However, no responsibility is assumed by Wilson
Electronics, Inc. for any business or personal losses arising from its use, or for
any infringements of patents or other rights of third parties that may result from
its use.
Copyright © 2011 Wilson Electronics, Inc. All rights reserved.
Figure 1
Figure 2
Mount the Antenna
Apply a small amount of thread-locker liquid to the threads on each of the six radials
and screw them into the holes at the base of the antenna. Attach the supplied L-bracket
to a sturdy vertical surface using four screws. It may also be attached to a pole with the
supplied U-bolt assembly (Figure 1). Remove the hex-nut and lock-washer from the base
of the antenna, thread the antenna cable through the large hole in the L-bracket, slip the
lock washer and hex-nut over the end of the cable and tighten against the underside of
the L-bracket to hold the antenna securely (Figure 2).
RF Safety Warning: The antenna must be installed with a separation of at least 16 inches from any persons and
must not be located or operating in conjunction with any other antenna or signal booster.
!
Connect the Cable
Connect the extension cable (sold separately) to the antenna cable, route the
extension cable to the signal booster location, and connect the extension cable to the
signal booster. (See the instructions that came with your Signal Booster for power-up
procedure.)
If you are connecting the antenna directly to a cell phone or data card, connect the cable
to the appropriate adapter (sold separately) and attach the adapter to your phone or data
card.
Technical Support
For expert assistance with your installation, call Wilson Electronics Technical Support
Department toll-free at 866-294-1660. Representatives are available to assist you
between 7:00 a.m. and 6:00 p.m. (MST) Monday through Friday. You may also visit the
Technical Support section of our website: www.WilsonElectronics.com.

Antenna Specifications
Part Number 301201 301202
Frequency Range 700-800 MHz / 824-894 MHz / 880-960 MHz / 1850-1990 MHz
Impedance 75 ohms 50 ohms
Antenna Gain 3.2 dBi 700-800 MHz / 4.1 dBi 824-894 MHz / 2.7 dBi 880-960 /
5.1 dBi 1850-1990 MHz
Radiation Omni
Polarization Vertical
Ground Plane Built-in
Connector F-Female FME Female
Material Whip - Stainless Steel / Casing - Fiberglass
Height 18 inches / 45.7 cm
Part #103045 AIG OD 011 / 06.28.11
3301 East Deseret Drive, St. George, UT 84790
For additional Technical Support visit www.WilsonElectronics.com
or email at: [e-mail]
Phone: [phone] Local: 435-673-5021 Fax: [phone]
www.twitter.com/WilsonCellular www.facebook.com/WilsonCellular
30-Day Money-Back Guarantee
All Wilson Electronics products are protected by Wilson Electronics 30-day
money-back guarantee. If for any reason the performance of any product is not
acceptable, simply return the product directly to the reseller with a dated proof of
purchase.
90-Day Warranty
Wilson Electronics antennas are warranted for ninety (90) days against defects in
workmanship and/or materials. Warranty cases may be resolved by returning the
product directly to the reseller with a dated proof of purchase.
Antennas may also be returned directly to the manufacturer at the consumer’s
expense, with a dated proof of purchase and a Returned Material Authorization
(RMA) number supplied by Wilson Electronics. Wilson Electronics shall, at its
option, either repair or replace the product. Wilson Electronics will pay for delivery
of the repaired or replaced product back to the original consumer if located within
the continental U.S.
This warranty does not apply to any antennas determined by Wilson Electronics
to have been subjected to misuse, abuse, neglect, or mishandling that alters or
damages physical or electronic properties.
RMA numbers may be obtained by phoning Technical Support at 866-294-1660.