Wilson Electronics 301133 User manual

Features:
• Multi-Band (700/800/900/1900 MHz)
• Analog and digital
• Improves voice and data signal quality
• Designed for RV’s
• Built-in spring reduces impact damage
• Built-in ground plane allows for mounting on any surface
RV / Trucker
Spring Mount
Cellular Antenna
Antenna
#301133
KIT# 308433

1Contact CellPhoneSignalBooster.us Technical Support Team with any questions at 800-501-3153
or email: [e-mail] Mon.- Fri. Hours: 7 am to 6 pm MST.
2
How it Works
Wilson Electronics RV / Trucker Spring-Mount Cellular Antenna will collect the cell tower
signal and send it through the cable to a Signal Booster or directly to the cell phone or
laptop data card. When the cell phone or data card transmits, the signal is transferred to a
Signal Booster or directly to the antenna and transmitted back to the cell tower.
Antenna Adapter Required (Sold Separately)
A phone/data card-specific, Antenna Adapter is required when connecting the antenna
directly to a cell phone. To identify the correct adapter, see Wilson Electronics Adapter
Guide at https://cellphonesignalbooster.us or contact Technical Support at 800-501-3153.
RV Package
1 - RV / Trucker Antenna
6 - Radials (3 short, 3 long)
1 - Thread-locker liquid
1 - 3-way mount (included in kit #308433)
Trucker Antenna
3-Way Mount
Installing the Antenna
1. Select a suitable location to install the
antenna on your RV, as high on the
vehicle as possible and at least 12
inches away from any other antenna.
For best results, use Wilson Electronics
3-Way Mount (#901104). This bracket will
enable you to mount the antenna on a
mirror or attach it to the side of your RV.
2. If you are installing on a mirror, clamp
the mount to the mirror support and
tighten the four nuts and bolts. If you are
mounting directly to the side of your RV,
remove the nuts, bolts and the smaller
half of the mount and use the four holes
in the larger half to attach it flush to the
side of the RV, using screws or bolts,
nuts and washers appropriate for your
particular installation. In both cases, be
sure the flat mounting base of the mount
is positioned up.

1
2
3. Screw the six antenna
radials into the holes under
the plastic coil housing on
the antenna. The included
thread-locker liquid must be
used to ensure the radials do
not vibrate loose. Tighten the
radials snugly with a wrench.
4. Loosen the jam nut at
the base of your antenna.
Remove it, along with the
star washer and the flat
washer.
5. Thread the cable down
through the hole in the
flat mounting base until
the antenna is positioned
vertically on the base. Then
thread the flat washer, star
washer and jam nut (in that order) back onto the cable and up to the threaded base of
the antenna. Tighten the jam nut to the underside of the mounting base with a wrench.
CAUTION: Do not over-tighten.
6. Route the cable from the antenna to the location where you will be using your phone or
data card. Extension cables up to 10 feet in length are available through your dealer.
7a. To connect directly to a cell phone or data card:
• Connect the antenna cable to the connector on the adapter (sold separately).
• Connect the adapter to your cell phone or data card.
7b. To connect to a Wilson Electronics Direct Connect Signal Booster (sold separately):
• Using the included cable wrench, connect the antenna cable to the side of the Signal
Booster labeled “Outside Antenna.”
• Connect the adapter extension cable to the side of the Signal Booster labeled
“Cellular Phone.”
• Connect the adapter extension cable to the adapter.
• Connect the adapter to your cell phone or data card.
7c. To connect to a Wilson Electronics Mobile Wireless Signal Booster (sold separately):
• Using the included cable wrench, connect the antenna cable to the side of the Signal
Booster labeled “Outside Antenna.”
Warning: If using a Signal Booster, ensure that all antenna and adapter cables are
connected before powering up the Signal Booster.
Disclaimer: The information provided by Wilson Electronics, Inc. is believed
to be complete and accurate. However, no responsibility is assumed by Wilson
Electronics, Inc. for any business or personal losses arising from its use, or for
any infringements of patents or other rights of third parties that may result from
its use.
Copyright © 2012 Wilson Electronics, Inc. All rights reserved.
Install Options
Install ush on side on mirror
or
Mon.- Fri. Hours: 7 am to 6 pm MST.
gnalbooster.us
or email: sales@cellphonesi
3153
-
501
Technical Support Team with any questions at 800-
PhoneSignalBooster.us
Contact Cell

Part #103007_REV12_06.19.12
Antenna Specifications
Part Number 301133 & 308433
Frequency Range 700-800 MHz / 824-894 MHz / 880-960 MHz / 1850-1990 MHz
Impedance 50 ohms
Antenna Gain 3.1 dB 700-800 MHz / 4.1 dBi 824-894 MHz / 2.0 dB 880-960 MHz /
5.1 dBi 1850-1990 MHz
Radiation Omni
Polarization Vertical
Ground Plane Built-in Ground Plane
Connector FME Female
Material Whip - Stainless Steel
Coax Cable RG58 - 13.5 feet / 4.11 meters
Height 21.5 inches including spring mount / 54.61 cm
Mount Standard CB 3/8 inch x 24 thread
For additional Technical Support visit https://cellphonesignalbooster.us
or email at: s[email protected]
Phone: [phone]
30-Day Money-Back Guarantee
All Wilson Electronics products are protected by Wilson Electronics 30-day money-
back guarantee. If for any reason the performance of any product is not acceptable,
simply return the product directly to the reseller with a dated proof of purchase.
1-Year Warranty
Wilson Electronics Trucker Spring Mount Dual-Band Cellular Antenna is warranted
for one (1) year against defects in workmanship and/or materials. Warranty cases
may be resolved by returning the product directly to the reseller with a dated proof
of purchase.
Antennas may also be returned directly to the manufacturer at the consumer’s
expense, with a dated proof of purchase and a Returned Material Authorization (RMA)
number supplied by Wilson Electronics. Wilson Electronics shall, at its option, either
repair or replace the product. Wilson Electronics will pay for delivery of the repaired
or replaced product back to the original consumer within the continental U.S.
This warranty does not apply to any antennas determined by Wilson Electronics
to have been subjected to misuse, abuse, neglect, or mishandling that alters or
damages physical or electronic properties.
RMA numbers may be obtained by contacting Technical Support at 800-501-3153 or
e-mail sale[email protected] or visit https://cellphonesignalbooster.us