Wilson Electronics SignalBoost DT User manual

SIGNALBOOST™DT
Multi-Band Outside
Cradle Antenna
Appearance of device and accessories may vary.
Antenna

1Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected]. Hours: 7 am to 6 pm MST.
2
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected]. Hours: 7 am to 6 pm MST.
How It Works
Wilson Electronics DT Cradle Mount antenna will collect the cell tower signal and send
it through the cable to a Signal Booster or directly to the cell phone or cellular data card.
When the cellular device transmits, the signal is transferred to a Signal Booster or directly
to the antenna and transmitted back to the cell tower.
What This Guide Includes
It is best to install this antenna at a level that is high enough to communicate with the
nearest cell tower. The following guide describes three options for mounting the antenna
on a pole, on an outside wall, and on an inside window. Please read the guide carefully to
help you decide what the best location is for your installation.
Compatibility with Wilson Electronics Signal Booster
The Cradle Antenna has been designed for use with the SIGNALBOOST DT Cellular
Signal Booster. However, it is compatible with other Wilson Electronics Signal Boosters.
If you choose to use this antenna with another Wilson Electronics Signal Booster, you
may need to purchase additional connectors or adapters. Contact Technical Support for
assistance with installation advice at 866-294-1660. 1. The supplied pole-mount bracket is designed to accommodate a pole diameter of 1
to 2 inches. Install the pole in the desired location using your own hardware.
2. Insert the supplied U-bolt through the holes in the cradle and slide one half of the
bracket assembly onto the U-bolt. (Figure 2)
3. Fitting the assembly onto the pole, slide the second half of the bracket onto the U-bolt
and secure it with lock washers and nuts. Be sure the cradle is at the desired height
on the pole and is rotated toward the nearest cell tower before tightening the nuts.
(Do not over-tighten the nuts.)
4. Insert the antenna into the cradle with the Wilson Electronics insignia facing in
the direction of the cell tower. The cable connection should protrude through the
bottom of the cradle. (Figure 1)
5. Connect one end of the supplied cable to the antenna. Route the cable as desired
to where the Signal Booster will be located. Depending on the distance between the
Signal Booster and antenna, you may need one or both lengths of the cable. If you
use both, connect them together with the cable connector (971129 sold separately).
Cell
Tower
Antenna
and
Cradle
Warning: Take care to ensure that neither you nor the pole comes near any power lines
during installation.
Outside Pole Mount (Packet A)
Figure 1 Figure 2
Cradle Antenna
(Mount outside on pole, wall, or
inside on a rafter or a window)
Wall Mount
(Packet B)
Pole Mount
(Packet A)
Window Mount
(Packet C)
Appearance of device and accessories may vary.
Options & Accessories
A. 75 Ohm Lightning Surge Protector F-Connector (859988)
B. F Female Connector for RG6 Cable (971129)
A B
Lightning
Surge Protector
(sold separately)
Signal Booster
Surge Protector
Power Strip recommended for all AC power supplies
To Outside
Antenna
Ground Wire
(not included)
To Inside
Antenna
Installing Lightning Protection
(sold separately)
Install the Lightning Surge Protector (LSP)
close to the Signal Booster. Attach the
cable from the Outside Antenna to the
surge protector, using a short length of
low loss cable; attach one end to the LSP
and the other to the Outside Antenna
connector on the Signal Booster. Ensure
the LSP is properly grounded. LSP may be
purchased at www.WilsonElectronics.com
or call 800-204-4104 (part #859988).
B

3Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected]. Hours: 7 am to 6 pm MST.
4
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected]. Hours: 7 am to 6 pm MST.
1. Select a location on an outside wall
as high as possible and at least 20
vertical feet away from where the
Signal Booster will be located.
2. Using the cradle as a template,
position it on the wall in the desired
location and mark the screw holes
with a pencil.
3. Drill two holes where marked, using
a 3/16-inch bit, and insert the screw
anchors.
4. Line up the holes in the cradle with
the screw anchors and mount the
cradle to the wall using two screws
and two washers. Tighten the screws
with a phillips-head screwdriver.
(Figure 5)
5. Insert the antenna into the cradle
with the Wilson Electronics
insignia facing in the direction
of the cell tower. The cable
connection should protrude through
the bottom of the cradle. (Figure 3)
6. Connect one end of the supplied
cable to the antenna. Route the
cable as desired to where the Signal
Booster will be located. Depending
on the distance between the Signal
Booster and antenna, you may need
one or both lengths of the cable. If
you use both, connect them together
with the cable connector (971129 sold
separately).
Min. 20 feet
Antenna
and
Cradle
Cell
Tower
Outside Wall Mount (Packet B) Inside Window Mount (Packet C)
1. Select a location on the inside of
the window as high as possible and
at least 20 vertical feet from where
the Signal Booster will be located.
(Figure 6 & 7)
2. Clean the area on the glass with the
supplied alcohol prep pad.
3. Use the suction cups provided in
Packet A. Using a twisting motion,
press the suction cups into the two
holes on the antenna cradle (see
Figure 8), then press the cradle onto
the glass at the desired location.
4. Insert the antenna into the cradle
with the Wilson Electronics
insignia facing in the direction
of the cell tower. The cable
connection should protrude through
the bottom of the cradle.
5. Connect one end of the cable to
the antenna and route the cable as
desired to where the Signal Booster
will be located. Depending on the
distance between the Signal Booster
and antenna, you may need one or
both lengths of the cable. If you use
both, connect them together with
the cable connector (971129 sold
separately).
Suction cup
installation
Antenna
and
Cradle
Min. 20 feet
Note: Window mounting the antenna will degrade the performance of your
system due to the metal oxide film applied to most windows.
Figure 3
Figure 6
Figure 7
Figure 8
Figure 4
Figure 5

5Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected]. Hours: 7 am to 6 pm MST.
6
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected]. Hours: 7 am to 6 pm MST.
About Wilson Electronics
Wilson Electronics, Inc., a leader in the wireless communications industry for over 40
years, designs and manufactures Signal Boosters, antennas and related components
that significantly improve cellular telephone signal reception and transmission in a variety
of mobile, small building, and large building applications.
With extensive experience in antenna and Signal Booster research and design, the
company’s engineering team uses a state-of-the-art testing laboratory, including
an anechoic chamber and network analyzers, to fine-tune antenna designs and
performance. For its Signal Boosters, Wilson Electronics uses a double electrically
insulated RF enclosure and cell tower simulators for compliance testing.
Wilson Electronics Signal Boosters feature patent-pending Smart Technology ™ that
enables them to automatically adjust their power based on cell tower requirements. By
detecting and preventing oscillation, signal overload and interference with other users,
these Smart Technology ™ Signal Boosters improve network cell phone areas without
compromising carrier systems.
All products are engineered and assembled in the company’s 55,000-square-foot
headquarters in St. George, Utah. Wilson Electronics has product dealers in all 50
states and in countries around the world.
RF Safety Warning
Warning: RF Safety: The cradle mount antenna, when used with
the cable included with the SIGNALBOOST DT product,
must have a separation distance of at least 8 inches from
all persons. If the cable is shortened, or if a different type
of cable is used, or if a different antenna is used, consult
with Wilson Electronics Technical Support to verify that
the planned installation is safe. Call 866-294-1660 or
435-673-5021, or email [e-mail].
Warning: Take care to ensure that neither you nor the pole comes
near any power lines during installation.
30-Day Money-Back Guarantee
All Wilson Electronics products are protected by Wilson Electronics 30-day money-
back guarantee. If, for any reason, the performance of any product is not acceptable,
simply return the product directly to the reseller with a dated proof of purchase.
90-Day Warranty
Wilson Electronics antennas are warranted for ninety (90) days against defects in
workmanship and/or materials. Warranty cases may be resolved by returning the
product directly to the reseller with a dated proof of purchase.
Antennas may also be returned directly to the manufacturer at the consumer’s
expense, with a dated proof of purchase and a Returned Material Authorization
(RMA) number supplied by Wilson Electronics. Wilson Electronics shall, at its option,
either repair or replace the product. Wilson Electronics will pay for delivery of the
repaired or replaced product back to the original consumer if within the continental
U.S.
This warranty does not apply to any antennas determined by Wilson Electronics
to have been subjected to misuse, abuse, neglect, or mishandling that alters or
damages physical or electronic properties.
RMA numbers may be obtained by phoning Technical Support at 866-294-1660.
Disclaimer: The information provided by Wilson Electronics, Inc. is believed to
be complete and accurate. However, no responsibility is assumed by Wilson
Electronics, Inc. for any business or personal losses arising from its use, or for
any infringements of patents or other rights of third parties that may result from
its use.
Copyright © 2012 Wilson Electronics, Inc. All rights reserved.

Part #104034_AIGDTCM_Rev07_01.06.12
Antenna Specifications
Part Number 301141
Frequency Range 824-960 MHz / 880-960 MHz / 1850-1990 MHz / 2110-2170 MHz
Impedance 75 ohms
Antenna Gain 4 dBi 824-894 MHz / 3.6 dBi 880-960 MHz /
5.5 dBi 1850-1900 MHz / 4.7 dBi 2110-2170 MHz
Radiation Omni
Polarization Vertical
Ground Plane None Required
Connector F-Female
Material ABS Plastic
Coax Cable RG 6
Height 8”
Mount Pole, Window or Wall
3301 East Deseret Drive, St. George, UT 84790
For additional Technical Support visit www.WilsonElectronics.com
or email at: [email protected]
Phone: [phone] Local: 435-673-5021 Fax: [phone]
www.twitter.com/WilsonCellular www.facebook.com/WilsonCellular