Wilson Electronics 301102 User manual

Antenna
Installation
Guide
Multi-Band
Glass-Mount
Antenna
PART# 301102
Features:
• Vehicle, home or ofce use
• Installs easily
• Permanent installation
• Built-in ground plane
• Requires antenna adapter (sold separately)
• Compatible with Wilson Electronics Signal Boosters
Wilson
®
Electronics, Inc.
Dual-Band Mini
Glass-Mount
Antenna
PART# 301114

1Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected]. Hours: 7 am to 6 pm MST.
2
How They Work
Wilson Electronics Glass Mount and Mini Glass-Mount antennas will collect the
cell tower signal and send it through the cable to a Signal Booster or directly to
the cell phone or cellular data card. When the cell phone or cellular data card
transmits, the signal is transferred to a Signal Booster or directly to the antenna
and broadcast back to the cell tower.
Antenna Adapter
An 18-inch external adapter is required to connect the cellular device to the
antenna. The external adapter is cell phone/data card-specic and may be
purchased through a local retailer. Refer to Wilson Electronics Adapter Guide to
identify the right adapter for your cell phone or cellular data card. The Adapter
Guide is available on our web site, www.WilsonElectronics.com, or you may call
Technical Support at 866-294-1660.
The antenna may be mounted along
the top of the front or rear window.
For best performance, don’t mount on
the rear window of trucks or SUVs.
Check to ensure your mounting
location will not interfere with
windshield wiper operation.
Keep the antenna away from defogger
wires and metallic aftermarket window
tint - most factory tint is nonmetallic
and will not interfere. If the antenna
must be mounted on the defogger,
center it between the defogger wires
as much as possible.
Clean the outside window surface
with glass cleaner or the alcohol swab
included in your package. Be sure the
same location inside the window is
clear of obstacles.
Avoid
Defogger
Wires
Possible Mounting
Locations
Wilson Electronics Signal Boosters Amplify Coverage
A Wilson Electronics Signal Booster (sold separately), when used in conjunction
with your antenna, can improve your cellular device coverage signicantly.
Wilson Electronics manufactures a wide range of wireless and Direct-Connect
Signal Boosters for mobile or in-building use. See your dealer for details or visit
www.WilsonElectronics.com.

1
2
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected]. Hours: 7 am to 6 pm MST.
Warning: The antenna and coupling box must be properly positioned or they will fail to function.
Both direction indicator arrows must face the same direction when the antenna is installed.
!
Disclaimer: The information provided by Wilson Electronics, Inc. is believed to
be complete and accurate. However, no responsibility is assumed by Wilson
Electronics, Inc. for any business or personal losses arising from its use, or for
any infringements of patents or other rights of third parties that may result from
its use.
Copyright © 2011 Wilson Electronics, Inc. All rights reserved.
Direction Indicator
Direction Indicator
Antenna
Base
Coupling
Box
Remove the protective paper on the
base to expose the adhesive pad and
rmly press the antenna into place on
the outside of the window. Note: If
installing on a home or ofce window,
ensure that it is not dual-pane glass.
Not recommended for RVs - too much
metal above the window will interfere
with operation.
The coupling box is installed on the
inside of the glass in the same position
as the antenna base on the outside.
Clean the inside surface with window
cleaner or the alcohol swab included
in your package.
The coupling box must be installed
so the arrow indicator faces the same
direction of the arrow indicator on the
antenna base.
Remove the protective paper to
expose the adhesive pad and rmly
press the coupling box into place.
Connect the cable to your adapter
cable or Signal Booster.

Wilson
®
Electronics, Inc.
Antenna Specications
Part Number 301102 301114
Frequency Range 700-800 MHz / 824-894 MHz
880-960 MHz / 1850-1990 MHz 824-894 MHz / 1850-1990 MHz
Impedance 50 ohms
Antenna Gain
1.8 dBi 700-800 MHz /
3.5 dBi 824-894 MHz /
2.8 dBi 880-960 MHz /
4.8 dBi 1850-1990 MHz
1.4 dBi 824-894 MHz /
2.4 dBi 1850-1990 MHz
Radiation Omni
Polarization Vertical
Ground Plane Built-in ground plane
Connector FME-Female
Material Whip - stainless steel Whip - plastic coated steel wire
Coax Cable RG58 - 14 feet / 4.27 meters
Height 15 inches / 38.10 cm 5.375 inches / 13.65 cm
Mount Glass mounting with 3M™ adhesive
30-Day Money-Back Guarantee
All Wilson Electronics products are protected by Wilson Electronics 30-day money-back guarantee. If, for
any reason, the performance of any product is not acceptable, simply return the product directly to the
reseller with a dated proof of purchase.
90-Day Warranty
Wilson Electronics antennas are warranted for ninety (90) days against defects in workmanship and/or
materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated
proof of purchase.
Antennas may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof
of purchase and a Returned Material Authorization (RMA) number supplied by Wilson Electronics. Wilson
Electronics shall, at its option, either repair or replace the product. Wilson Electronics will pay for delivery of
the repaired or replaced product back to the original consumer.
This warranty does not apply to any antennas determined by Wilson Electronics to have been subjected to
misuse, abuse, neglect, or mishandling that alters or damages physical or electronic properties.
RMA numbers may be obtained by phoning Technical Support at 866-294-1660.
3301 East Deseret Drive, St. George, UT 84790
For additional Technical Support visit www.WilsonElectronics.com
or email at: [email protected]
Phone: [phone] Local: 435-673-5021 Fax: [phone]
www.twitter.com/WilsonCellular www.facebook.com/WilsonCellular
Part #103018 AIG DBGM 007 / 07/14/11