Wilson Electronics 304452-50 User manual

Wide-Band
Panel Antenna
Window, Ceiling, Wall
& Outdoor Mounts
Wilson
®
Electronics, Inc.
The wide-band panel antenna is vertically polarized. For optimum
performance, install the antenna with the cable running from the
bottom or the top.
WINDOW
PART# 304452-50 Ohms
PART# 304472-75 Ohms
CEILING
PART# 304451-50 Ohms
PART# 304471-75 Ohms
WALL
PART# 301135-50 Ohms
UPGRADE-PART# 301147-50 Ohms
PART#301155-75 Ohms
OUTDOOR
PART# 301157-50 Ohms
Appearance of device and accessories may vary.
Antenna

1Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
Or email: [email protected] Hours: 7am to 6pm MST.
2
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
Or email: [email protected] Hours: 7am to 6pm MST.
Window Mount:
PART# 304452 PART# 304472
Ceiling Mount:
PART# 304451 PART# 304471
Wall Mount:
PART# 301135 UPGRADE-PART# 301147
PART#301155
Outdoor Mount:
PART# 301157-50 Ohms
Optional In-Wall
Mount Accessory:
PART#301155
In-Wall Mounting
Bracket
(901123)
Wilson Signal Boosters Amplify Coverage
When used in conjunction with your antenna, a Wilson Electronics Signal
Booster can improve your cell phone and laptop data card coverage area
more than 20 times. Wilson Electronics manufactures a wide range of
Wireless, Direct-Connect and Adjustable Gain Signal Boosters for mobile
or in-building use.
See your dealer for details or visit www.WilsonElectronics.com.
See your dealer for details or visit
Appearance of device and accessories may vary.
Wide-Band Panel Antenna
Window, Ceiling, Wall & Outdoor Mounts
Window Mount Installation
Find the window that faces the direction of the nearest cell tower. The
signal strength function on your cell phone can help you determine this.
See the Technical Support section of Wilson Electronics website,
www.WilsonElectronics.com, for instructions on accessing the signal
strength function on your particular phone.
Choose an inside window location where the antenna will be hung.
Clean the window and the suction cups with glass cleaner.
It is important that the small tabs on each suction cup be facing outward
so they may be used to remove the antenna from the window if desired.
Use fi rm and even pressure to attach the antenna to the window without
breaking the glass. Avoid excessive or sudden pressure against the
glass.
Refer to Signal Booster instructions for separation requirements.
To be used as your outside antenna which communicates with the cell tower
Wide-Band
Panel Antenna
Window Cradle
Mount
Attach to Window
Slide Panel
Antenna into
cradle

3Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
Or email: [email protected] Hours: 7am to 6pm MST.
4
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
Or email: [email protected] Hours: 7am to 6pm MST.
Wall Mount InstallationCeiling Mount Installation
Find the desired location for the Panel Antenna. Verify that the Panel
Antenna and the Outside Antenna have the necessary separation (see
Signal Booster instructions for requirements).
For optimum results, the antenna should be mounted a minimum of 6
feet from the fl oor.
Utilize Wall Mount Bracket (see diagram below) as your template. Drill
out the four holes for the screws in the wall, using a 3/16 size drill bit,
following your template. Tap in wall anchors provided and place the
mounting bracket over the wall anchors, insert the screws and tighten.
Slide the Panel Antenna onto the wall mount bracket (see diagram
below).
Wide-Band Panel Antenna
with Ceiling Mount
anchor
slide into
mount
drywall
anchor
anchor &
screw
anchor &
screw
drill 5/8”
hole in ceiling
for end connector
anchor
Select a location on the ceiling that you can access from above to
run the antenna cable. Verify that your chosen location allows for
the necessary separation between the Inside and Outside Antenna
(see Signal Booster installation instructions for antenna separation
requirements).
Use the antenna as your template in your predetermined location.
Note: Ensure that the cable connector location is NOT below a ceiling
rafter.
Drill a hole large enough to accommodate the dimension of the
connector on the location you have marked for the cable. Hold the
antenna to the ceiling and mark the locations for the screws and then
drill a 3/16” hole and tap anchors into the pre-drilled screw holes.
Attach the Signal Booster “Inside Antenna” cable to the connector on the
Ceiling Mount Antenna. Place the antenna fl ush against the ceiling, and
then screw the antenna into place (screws and anchors provided). Be
careful not to over-tighten.
If you have any questions about the installation procedure, please
contact our Technical Support Team toll free at 866-294-1660 or email
[email protected].
Wide-Band
Panel Antenna
Wall Mount
& hardware

5Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
Or email: [email protected] Hours: 7am to 6pm MST.
6
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
Or email: [email protected] Hours: 7am to 6pm MST.
Cell Tower
RF Signal
Wide Band
Antenna
-50dB -60dB -70dB -80dB -90dB -100dB -110dB
EXCELLENT
Signal Strength
GOOD
Signal Strength
POOR
Signal Strength
NO
SIGNAL
-50dB
-60dB
-70dB
-80dB
-90dB
-100dB
-110dB
EXCELLENT
Signal Strength
GOOD
Signal Strength
POOR
Signal Strength
NO
SIGNAL
Adjusting the Antenna for Maximum Performance
To adjust the antenna for best performance, connect it to your cell
phone with an external adapter and a length of cable. External Antenna
Adapters and cables are sold separately. Put the cell phone in test
mode and turn the antenna in 10-degree increments while checking
the cell phone’s signal level. At each point you may need to wait a few
seconds as your cell phone updates. To fi nd your phone’s test mode,
visit www.WilsonElectronics.com.
Once you have obtained the strongest signal, fully tighten the mounting
hardware. After the Signal Booster and the rest of the system is installed
and performing correctly, weatherproof all connections.
Important: If you are using a wireless Signal Booster, be sure the
antenna is not pointing across the building in which you are trying
to get coverage. The antenna should point away from the building
to help prevent oscillation (feedback).
Ultra low loss cable is recommended for lengths 20’ or greater to prevent
signifi cant signal loss. Wilson Electronics offers WILSON 400 cable in
several lengths from 20-100 feet. Wilson Electronics also offers a wide
range of phone adapters to connect your cell phone to a Signal Booster
or directly to the antenna. To fi nd the adapter for your phone, visit
www.WilsonElectronics.com or call toll free 866-294-1660.
Signal readings usually appear as a negative number (for example, -86).
The larger the number, the more powerful the signal (-75 is stronger than
-84). See graph above.
The antenna should be mounted as shown in the illustration below. The
included mounting bracket is adjustable and will accommodate pipe
diameters from 1.25” to 2” (pipe sold separately part# 901117). Mount
the antenna so that there is at least 3 feet of clearance in front and
sides. Position the antenna so that it has the most unobstructed line of
sight to the cellular service provider’s strongest signal. If you are using
a wireless Signal Booster, make sure the antenna is not pointing across
your own roof.
Refer to Signal Booster instructions for separation requirements.
Warning: Lightning protection is recommended for all
installations, sold separately (Wilson Electronics Part #859902).
Take extreme care to ensure that neither you nor the antenna
comes near any electric power lines.
Outdoor Mount Installation
Wide-Band
Panel Antenna
pipe sold separately
part# 901117
Postion for strongest signal
Outdoor Mount
& hardware

Part# 103074_Rev01_11.16.11
Wilson
®
Electronics, Inc.
Antenna Specifi cations
Part Number 301134 301135 301147 304451 304452 301157 301155 304471 304472
Frequency Range 700-800 MHz / 824-894 MHz / 880-960 MHz / 1710-1880 MHz
1850-1900 MHz / 2110-2170 MHz
Impedance 50 ohms 75 ohm
Gain
5.2 dBi 700-800 MHz / 4.4 dBi 824-894 MHz / 4.2 dBi 880-960 MHz /
10.1 dBi 1710-1880 MHz / 10.6 dBi 1850-1990 MHz /
8.2 dBi 2110-2170 MHz
Polarization Vertical
Beamwidth Horizontal Plane 70 / 60 Deg
Beamwidth Vertical Plane 50 / 45 Deg
Max Power 50 watts
Connector N-Female F-Female
Dimension 8.27 x 7.09 x 1.73 (inch) / 21 x 18 x 4.39 (cm)
Weight 1.32 lbs / 0.6 kg
30-Day Money-Back Guarantee
All Wilson Electronics products are protected by Wilson Electronics 30-day money-back guarantee. If,
for any reason, the performance of any product is not acceptable, simply return the product directly to
the reseller with a dated proof of purchase.
90-Day Warranty
Wilson Electronics antennas are warranted for ninety (90) days against defects in workmanship and/
or materials. Warranty cases may be resolved by returning the product directly to the reseller with a
dated proof of purchase.
Antennas may also be returned directly to the manufacturer at the consumer’s expense, with a dated
proof of purchase and a Returned Material Authorization (RMA) number supplied by Wilson Electronics.
Wilson Electronics shall, at its option, either repair or replace the product. Wilson Electronics will pay for
delivery of the repaired or replaced product back to the original consumer.
This warranty does not apply to any antennas determined by Wilson Electronics to have been subjected
to misuse, abuse, neglect, or mishandling that alters or damages physical or electronic properties.
RMA numbers may be obtained by phoning Technical Support at 866-294-1660.
Disclaimer: The information provided by Wilson Electronics, Inc. is believed to be complete and
accurate. However, no responsibility is assumed by Wilson Electronics, Inc. for any business or
personal losses arising from its use, or for any infringements of patents or other rights of third parties
that may result from its use.
Copyright © 2011 Wilson Electronics, Inc. All rights reserved.
3301 East Deseret Drive, St. George, UT 84790
For additional Technical Support visit www.WilsonElectronics.com
or email at: [email protected]
Phone: [phone] Local: 435-673-5021 Fax: [phone]
www.twitter.com/WilsonCellular www.facebook.com/WilsonCellular