Wilson Electronics 301114 User manual

Antenna
Antenna
Installation
G
u
ide
stallatio
stallat
Dual-Band
Glass-Mount
Antenna
PART# 301102
Features:
• Vehicle, home or office use
• Easy to install
• Permanent installation
• Built-in ground plane
• Requires antenna adapter (sold separately)
• Compatible with Wilson amplifiers (optional)
Wilson
®
Electronics, Inc.
Dual-Band Mini
Glass-Mount
Antenna
PART# 301114

1
30-Day Money-Back Guarantee
All Wilson Electronics products are protected by Wilson’s 30-day money-back
guarantee. If for any reason the performance of any product is not acceptable,
simply return the product directly to the reseller with a dated proof of purchase.
90-Day Warranty
Wilson Electronics antennas are warranted for ninety (90) days against defects in
workmanship and / or materials. Warranty cases may be resolved by returning the
product directly to the reseller with a dated proof of purchase.
Antennas may also be returned directly to the manufacturer at the consumer’s
expense, with a dated proof of purchase and a Returned Material Authorization
(RMA) number supplied by Wilson Electronics. Wilson shall, at its option, either
repair or replace the product. Wilson Electronics will pay for delivery of the repaired
or replaced product back to the original consumer.
This warranty does not apply to any amplifiers determined by Wilson Electronics
to have been subjected to misuse, abuse, neglect, or mishandling that alters or
damages physical or electronic properties.
RMA numbers may be obtained by phoning Technical Support at 866-294-1660.
How They Work
Wilson’s Dual-Band Glass Mount and Mini Glass-Mount antennas will collect the
cell tower signal and send it through the cable to an amplifier or directly to the cell
phone or cellular data card. When the cell phone or cellular data card transmits,
the signal is transferred to an amplifier or directly to the antenna and broadcast
back to the cell tower. See the back cover for information on Wilson amplifiers.
Antenna Adapter
An 18-inch external adapter is required to connect the cell phone or cellular data
card to the antenna. The external adapter is cell phone/data card-specific and
may be purchased through a local retailer. Refer to Wilson’s Adapter Guide to
identify the right adapter for your cell phone or cellular data card. TheAdapter
Guide is available through a local retailer. It is also available on our web site,
www.wilsonelectronics.com, or you may call Technical Support at 866-294-1660.
Disclaimer: The information provided by Wilson Electronics, Inc. is believed to
be complete and accurate. However, no responsibility is assumed by Wilson
Electronics, Inc. for any business or personal losses arising from its use, or for
any infringements of patents or other rights of third parties that may result from
its use.
Copyright © 2007 Wilson Electronics, Inc. All rights reserved.

2
The antenna may be mounted along
the top of the front or rear window. For
best performance don’t mount on the
rear window of trucks or SUVs.
Check to ensure your mounting
location won’t interfere with windshield
wiper operation.
Keep the antenna away from defogger
wires and metallic aftermarket window
tint - most factory tint is nonmetallic
and will not interfere. If the antenna
must be mounted on the defogger,
center it between the defogger wires
as much as possible.
Clean the exterior window surface
with glass cleaner or an alcohol swab.
Be sure the same location inside the
window is clear of obstacles.
Remove the protective paper on the
base to expose the adhesive pad and
firmly press the antenna into place on
the outside of the window. Note: If
installing on a home or office window,
ensure that it is not dual pane glass.
Not recommended for RVs - too much
metal above the window will interfere
with operation.
The coupling box is installed on
the interior of the glass in the same
position as the antenna base on the
outside. Clean the inside surface with
window cleaner or an alcohol swab.
The coupling box must be installed
so the arrow indicator faces the same
direction of the arrow indicator on the
antenna base.
Remove the protective paper to
expose the adhesive pad and firmly
press the coupling box into place.
Connect the coax cable to your
adapter cable or amplifier.
Warning: The antenna and coupling
box must be properly positioned or they will
fail to function. Both direction indicator
arrows must face the same direction when
the antenna is installed.
!
Direction Indicator
Direction Indicator
Antenna
Base
Coupling
Box
Possible Mounting
Locations
Avoid
Defogger
Wires

3301 East Deseret Drive, St. George UT 84790
For additional Technical Support visit
www.wilsonelectronics.com
Phone: [phone] Fax: [phone]
Part #000000 AIG DBGM 002 / 02.06.07
Wilson
®
Electronics, Inc.
Antenna Specifications
Part Number 301102 301114
Frequency Range 806-894 MHz / 1850-1990 MHz
Impedance 50 ohms
Antenna Gain 4.5 dBi 806-894 MHz /
5.9 dBi 1850-1990 MHz 1.4 dBi 806-894 MHz / 2.4 dBi 1850-1990 MHz
Radiation Omni
Polarization Vertical
Wavelength 1.1 Wavelength 806-894 MHz /
2.3 Wavelength 1850-1990 MHz 1/4 Wavelength 806-894 MHz / 9/16 Wavelength 1850-1990 MHz
Ground Plane Built-in ground plane
Connector FME-Female
Material Whip - Stainless Steel Whip - plastic coated steel wire
Coax Cable RG58 - 14 feet / 4.27 meters
Height 15 inches / 38.10 cm 5.375 inches / 13.65 cm
Mount Glass mounting with 3M™ adhesive
Wilson Amplifiers Boost Coverage Even More
A Wilson Electronics amplifier (sold separately), when used in conjunction with
your antenna, can improve your cell phone and laptop data card coverage
area up to 50 miles. Wilson manufactures a wide range of wireless and direct-
connection amplifiers for mobile or in-building use. See your dealer for details or
visit www.wilsonelectronics.com.