Wilson Electronics 311229 User manual

Installation Guide
Drive OTR Antenna

Index
Package Contents ............................................................1
Select Mounting Location & Assemble the Antenna .............................. 2
Mounting the Antenna ........................................................4
Mounting the Antenna with Spring ............................................ 5
Safety Guidelines & Specifications ............................................ 6
Warranty ....................................................................7

1
Package Contents
Drive OTR Antenna
w/16 ft. Cable
(311229)
13 in. & 18 in.
Mast Extensions
Spring, Side Exit
Adapter & 3-Way
Mount
Thread Lock

2
c
a
b
l
e
c
a
b
l
e
c
a
b
l
e
Once you have determined the best
location for the antenna, insert cable
through mast(s) then through Side
Exit Adapter .
Select Mounting Location &
Assemble the Antenna
cable from
antenna
Mast
Extension
13 in.
mast
antenna
13 in.
mast
13 in.
mast
Side Exit
Adapter
run cable
through Mast
Extension(s)
run cable
through Mast
Extension(s)
Antenna Spring
(can be used
optionally)
(Antenna Spring
should not be used)
on this length)
18 in.
mast

3
Use thread locker (provided) to thread
points and screw into place.
NOTE: Be sure the antenna is the correct
height before applying thread locker.
NOTE: When adding the side exit adapter
hold the antenna vertically and screw the
adapter from the bottom up. This reduces
cable twisting.
(Assemble the Antenna cont.)
Side Exit
Adapter
mast
mast
add thread
locker
add thread
locker
Drive OTR
Antenna
c
a
b
l
e
f
r
o
m
a
n
t
e
n
n
a

4
If the vehicle does not have built-in
mounting points, a three-way mount is
included that will work on vehicles with
mirror rails.
NOTE: The cable is strong enough that
it may be shut in most vehicle doors
without damaging the cable.
Mounting the Antenna
3-Way Antenna
Mount with hardware
connect cable to a
signal booster
Side Exit
Adapter
Mast Extension
add thread
locker

5
Mounting the Antenna with
Spring
3-Way Antenna
Mount with hardware
Side Exit
Adapter
Spring
Mast Extension
If installing with the Spring, disassemble
the 3-Way Mount and use disc washer
and nut (provided) to mount the antenna
with Spring as shown.
add thread
locker
add thread
locker
Remove nut & shake
proof washer
Remove bolt &
plastic washer
Mount disc washer with lip
in the DOWN position
Fasten nut with lip in
the UP position

6
Safety Guidelines & Specifications
RF Safety Warning: Any antenna used with this device must be located at least 8 inches from all persons.
AWS Warning: The Outside Antenna must be installed no higher than 32 feet 9 inches (10 meters) above ground.
311229
698–806 806–960 1710–1880 1850–1990 1910–2170 2300–2700
SMA (F)
2.4
1.4
1.8
<2:1
> 70 > 65
2.6
2.4
1.9
3.8
3.1
2.8
3.8
2.7
2.9
3.7
2.4
3.0
4.3
2.6
3.3
7.422 x 2.688 / 188 x 68
<2:1
.75 / .340
Vertical
Aluminum
Alumin Plastic Type: ASA (Acrylonitrile Styrene) Acrylate)
360 360 360 360 360 360
70 78 60 70 80 33
311 / 500
50
10
Model
Frequency Band (MHz)
Connector
Peak Gain (dBi)
Gain (dBi), Typical @ 2° Elevation
Cable loss LMR-195 30 in.
Dimensions (in / mm)
VSWR
Weight (lb./ kg)
Polarization
Eciency (%)
Radiator Material
Radome Material
Half-Power Azimuth Beamwidth (°)
Rated Wind Velocity (mph / kph)
Half-Power Elevation Beamwidth (°)
Impedance (Ω)
Maximum Power (W)
Mechanical Specifications
Electrical Specifications

7
DISCLAIMER: The information provided by Wilson Electronics, LLC is believed to be complete and accurate. However,
no responsibility is assumed by Wilson Electronics, LLC for any business or personal losses arising from its use, or for
any infringements of patents or other rights of third parties that may result from its use.
MARKETING APPROVAL: Installer and end customer hereby grants to Wilson Electronics the express right to use
installers or end customers company logo in marketing, sales, financial, and public relations materials and other
communications solely to identify Customer as a Wilson Electronics customer.
2 YEAR WARRANTY
Antennas may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of
purchase and a Returned Material Authorization (RMA) number supplied by Wilson Electronics. Wilson Electronics
shall, at its option, either repair or replace the product. Wilson Electronics will pay for delivery of the repaired or
replaced product back to the original consumer if located within the continental U.S.
Replacement products may include refurbished Wilson Electronics products that have been recertified to conform
with product specifications.
This warranty does not apply to any antennas determined by Wilson Electronics to have been subjected to misuse,
abuse, neglect, or mishandling that alters or damages physical or electronic properties.
RMA numbers may be obtained by contacting Technical Support at 866-294-1660.

8
Notes
1.866.294.1660 www.wilsonelectronics.com [e-mail]

9
Notes
1.866.294.1660 www.wilsonelectronics.com [e-mail]

NOT AFFILIATED WITH WILSON ANTENNA
3301 East Deseret Drive, St. George, UT
866.294.1660 www.wilsonelectronics.com [e-mail]
Copyright © 2020 Wilson Electronics. All rights reserved. Wilson Electronics products covered by U.S. patent(s) and pending
application(s) For patents go to: weboost.com/us/patents
GDE000299_Rev01_08.10.20