Wilson Electronics 304472 User manual

Wide-Band
Panel Antenna
Window, Ceiling, Wall
& Outdoor Mounts
The wide-band panel antenna is vertically polarized. For optimum
performance, install the antenna with the cable running from the
bottom or the top.
WINDOW
#304452
#304472
CEILING
#304451
#304471
WALL
#311135
UPGRADE- #311155-0630
#311155
POLE
# 314453
#314473
Appearance of device and accessories may vary.
Antenna

12
Contact Wilson Electronics Customer Support Team with any questions at
866-294-1660 or email: [email protected]
Window Mount:
#304452 - 50 Ohm
#304472 - 75 Ohm
Ceiling Mount:
#304451 - 50 Ohm
#304471 - 75 Ohm
Wall Mount:
#311135
#311155
Pole Mount:
#314453
#314473
Optional In-Wall
Mount Accessory:
In-Wall Mounting
Bracket
(901123)
Appearance of device and accessories may vary.
Wide-Band Panel Antenna
Window, Ceiling, Wall & Pole Mounts
(extra parts may be included in hardware packet)
Panel Antenna
w/F-Female Connectors
RG6 30’ Coax Cable
w/F-Male Connectors
Required F-Female to SMA
Male adapter #2F1165
#311155-0630
DT4G Inside Panel
Antenna Upgrade

2
Contact Wilson Electronics Customer Support Team with any questions at
866-294-1660 or email: [email protected]
Window Mount Installation
Find the window that faces the direction of the nearest cell tower. The
signal strength function on your cell phone can help you determine
this. Contact Customer Support at 866-294-1660 , for instructions on
accessing the signal strength function on your particular phone.
Choose an inside window location where the antenna will be hung.
Clean the window and the suction cups with glass cleaner.
It is important that the small tabs on each suction cup be facing outward
so they may be used to remove the antenna from the window if desired.
Use rm and even pressure to attach the antenna to the window without
breaking the glass. Avoid excessive or sudden pressure against the
glass.
Refer to Signal Booster instructions for separation requirements.
To be used as your outside antenna which communicates with the cell tower
Wide-Band
Panel Antenna
Window Cradle
Mount
Attach to
Window
Slide Panel
Antenna into
cradle
Panel
Antenna
remove tape
back panel
pull
Carefully pull back panel cover away from
antenna until tape releases (this will
take some force). Peel off tape and tape
residue before installing different mounting
options.
Remove Back Panel Before
Utilizing Other Mounting Options

34
Contact Wilson Electronics Customer Support Team with any questions at
866-294-1660 or email: [email protected]
Ceiling Mount Installation
anchor
wood screw
wood screw
anchor
drill hole in ceiling
for end connector
anchor
Select a location on the ceiling that you can access from above to
run the antenna cable. Verify that your chosen location allows for
the necessary separation between the Inside and Outside Antenna
(see Signal Booster installation instructions for antenna separation
requirements).
Use the antenna as your template in your predetermined location.
Note: Ensure that the cable connector location is NOT below a ceiling
rafter.
Panel Antenna
remove ceiling
mount panel from
Panel Antenna
before utilizing other
mounting options
Remove Ceiling Mount Before
Utilizing Other Mounting Options
Drill a hole large enough to accommodate the dimension of the
connector on the location you have marked for the cable. Hold the
antenna to the ceiling and mark the locations for the screws and then
drill a 3/16 inch hole and tap anchors into
the pre-drilled screw holes.
Attach the Signal Booster “Inside
Antenna” cable to the connector on the
Ceiling Mount Antenna. Place the
antenna ush against the ceiling, and
then screw the antenna into place
(screws and anchors provided). Be
careful not to over-tighten.
If you have any questions about the
installation procedure, please
contact our Customer Support Team toll
free at 866-294-1660 or email
[email protected].
Wide-Band Panel Antenna
Ceiling Mount

4
Contact Wilson Electronics Customer Support Team with any questions at
866-294-1660 or email: [email protected]
Wall Mount Installation
Find the desired location for the Panel Antenna. Verify that the Panel
Antenna and the Outside Antenna have the necessary separation (see
Signal Booster instructions for requirements).
For optimum results, the antenna should be mounted a minimum of 6
feet from the oor.
Utilize Wall Mount Bracket (see diagram below) as your template. Drill
out the four holes for the screws in the wall, using a 3/16 size drill bit,
following your template. Tap in wall anchors provided and place the
mounting bracket over the wall anchors, insert the screws and tighten.
Slide the Panel Antenna onto the wall mount bracket (see diagram
below).
Wide-Band
Panel Antenna
Wall Mount
& hardware
slide into
mount
drywall
anchor &
screw
anchor &
screw
Panel Antenna back view
remove back panel
mount from Panel
Antenna before
utilizing other
mounting options
Remove Mount Before Utilizing
Other Mounting Options

56
Contact Wilson Electronics Customer Support Team with any questions at
866-294-1660 or email: [email protected]
The antenna should be mounted as shown in the illustration below. The
included mounting bracket is adjustable and will accommodate pipe
diameters from 1.25 inches to 2 inches (pipe sold separately #901117).
Mount the antenna so that there is at least 3 feet of clearance in front
and sides. Position the antenna so that it has the most unobstructed line
of sight to the cellular service provider’s strongest signal. If you are using
a wireless Signal Booster, make sure the antenna is not pointing across
your own roof.
Refer to Signal Booster instructions for separation requirements.
Warning: Lightning protection is recommended for all installations,
sold separately (Wilson Electronics #859902-50 Ohm &
#859992-75 Ohm). Take extreme care to ensure that
neither you nor the antenna comes near any electric
power lines.
Pole Mount Installation
Postion for strongest signal
Pole Mount
& hardware
Wide-Band
Panel Antenna
pipe sold separately
#901117

6
Contact Wilson Electronics Customer Support Team with any questions at
866-294-1660 or email: [email protected]
Cell Tower
RF Signal
Wide Band
Antenna
-50dB -60dB -70dB -80dB -90dB -100dB -110dB
EXCELLENT
Signal Strength
GOOD
Signal Strength
POOR
Signal Strength
NO
SIGNAL
Adjusting the Antenna for Maximum Performance
To adjust the antenna for best performance, connect it to your cell
phone with an External Adapter and a length of cable (External Antenna
Adapters and cables are sold separately). Put the cell phone in test
mode and turn the antenna in 10-degree increments while checking
the cell phone’s signal level. At each point you may need to wait a few
seconds as your cell phone updates.
Once you have obtained the strongest signal, fully tighten the mounting
hardware. After the Signal Booster and the rest of the system is installed
and performing correctly, weatherproof all connections.
Important: If you are using a Wireless Signal Booster, be sure the
antenna is not pointing across the building in which you are trying
to get coverage. The antenna should point away from the building
to help prevent oscillation (feedback).
Ultra low loss cable is recommended for lengths 20 feet or greater to
prevent signicant signal loss. Wilson Electronics offers WILSON 400
cable in several lengths from 20-100 feet. Wilson Electronics also offers
a wide range of phone adapters to connect your cell phone to a Signal
Booster or directly to the antenna. To nd the adapter for your phone, or
contact Customer Support toll free 866-294-1660.
Signal readings usually appear as a negative number (for example, -86).
The larger the number, the more powerful the signal (-75 is stronger than
-84). See graph above.

103074_Rev15_05.04.17
2-Year Warranty
Wilson Electronics Signal Boosters are warranted for two (2) years against defects in workmanship
and/or materials. Warranty cases may be resolved by returning the product directly to the reseller with
a dated proof of purchase.
Antennas may also be returned directly to the manufacturer at the consumer’s expense, with a dated
proof of purchase and a Returned Material Authorization (RMA) number supplied by Wilson Electronics.
Wilson Electronics shall, at its option, either repair or replace the product. Wilson Electronics will pay for
delivery of the repaired or replaced product back to the original consumer.
This warranty does not apply to any antennas determined by Wilson Electronics to have been subjected
to misuse, abuse, neglect, or mishandling that alters or damages physical or electronic properties.
Replacement products may include refurbished Wilson Electronics products that have been recertied
to conform with product specications.
RMA numbers may be obtained by contacting Technical Support at 866-294-1660.
Disclaimer: The information provided by Wilson Electronics, LLC is believed to be complete and
accurate. However, no responsibility is assumed by Wilson Electronics, LLC for any business or
personal losses arising from its use, or for any infringements of patents or other rights of third parties
that may result from its use.
Copyright © 2016 Wilson Electronics, LLC. All rights reserved.
Wilson Electronics, LLC
3301 East Deseret Drive, St. George, UT 84790
For additional Technical Support visit www.WilsonElectronics.com
or email at: [email protected]
Phone: [phone] Local: 435-673-5021 Fax: [phone]
www.twitter.com/WilsonCellular www.facebook.com/WilsonCellular
Antenna Specifications
Part
Number 304452 304472 304451 304471 311135 314473 311155 314453 311155-0630
Frequency
Range
700-800 MHz / 824-894 MHz / 880-960 MHz / 1710-1880 MHz
1850-1900 MHz / 2110-2700 MHz
698-716 MHz / 776-787 MHz / 824-849 MHz / 1710-1755
MHz / 1850-1995 MHz
698-716 MHz / 776-787 MHz /
824-849 MHz / 1710-1755 MHz /
1850-1995 MHz
Impedance 50 Ohms 75 Ohms 50 Ohms 75 Ohms 50 ohms 75 ohms 75 Ohms 50 Ohms 75 Ohms
Connector N-Female F-Female N-Female F-Female N-Female F-Female F-Female N-Female F-Female
Antenna
Gain
5.2 dBi 700-800 MHz / 4.4 dBi 824-894 MHz / 4.2 dBi 880-960 MHz
/ 10.1 dBi 1710-1880 MHz / 10.6 dBi 1850-1990 MHz /
8 dBi 2110-2700 MHz
3.8 dBi 698-716 MHz / 3.6 dBi 776-787 MHz / 4.4 dBi 824-849
MHz / 8.2 dBi 1710-1755 MHz / 10.0 dBi 1850-1995 MHz
1.49 dBi 698-716 MHz / 1.26 dBi
776-787 MHz / 1.81 dBi 824-849
MHz / 4.25 dBi 1710-1755 MHz /
5.72 dBi 1850-1995 MHz
Polarization Vertical
Beamwidth
Horizontal
Plane
70 / 60 Deg
Beamwidth
Vertical Plane 50 / 45 Deg
Max Power 50 Watts
Dimension 8.27 x 7.09 x 1.73 (inch) / 21 x 18 x 4.39 (cm)
Weight 1.32 lbs / 0.6 kg