Winmate W22IB3S-PCA3 PPC User manual

Please read these instructions carefully before using this product, and save this manual for future use.
W22IB3S-PCA3 PPC
Quick Start Guide
Version 1.0
January 2015

W22IB3S Quick Start Guide 1
Introduction
Winmate’s W22IB3S-PCA3 is 21.5” flat Panel PC with Capacitive Touch Key for quick access to
hardware and display OSD control. The PPC features P-Cap multi-touch screen that supports
simultaneous 10-points Multi-touch for a better user experience.
Features
‧21.5” 1920 x 1080 Resolution with P-Cap Multi-touch Screen
•Low-power System with Intel®Celeron® N2930 Processor
•Fanless Cooling System and Ultra-low Power Consumption
•10-points Multi-touch with Windows 8
•Capacitive Touch Key for Hot key and Display Control
•Front IP66 Water and Dust Proof

2 W22IB3S Quick Start Guide
Appearance
Front View
Side View

W22IB3S Quick Start Guide 3
Rear View
Bottom View
Top View
No
Description
No
Description
1
USB 2.0 x 2 (Optional)
6
HDMI x 1
2
RS232 x 1 (Optional)
7
RJ-45 GbE LAN x 2
3
12V DC IN, 3-Pin Terminal Block x 1
8
4-Channel Isolated DIDO x 1 (Optional)
4
RS232/422/485 x 1
9
Audio Jack x 1 (Optional)
5
USB 3.0 x 1, USB 2.0 x 1
10
2W Speaker x 2

4 W22IB3S Quick Start Guide
Getting Started
Capacitor Touch Keys Introduction
The W22IB3S-PCA3 comes with five capacitive touch keys on the front panel for quick
access to hardware and display OSD control.
Touch Keys
Function
Description
Power
Power on/off control
Brightness/Volume
To increase brightness of panel
/To increase Volume
(by HotTab Setting)
Brightness/Volume
To decrease brightness of panel
/To decrease Volume
(by HotTab Setting)
Menu
Switch to Metro or Desktop
(by HotTab Setting)
Function
User programmable function key
(by HotTab Setting)

W22IB3S Quick Start Guide 5
Turning On / Off
Turning On
Press and hold the capacitive power key for 4 seconds until the blue LED backlight lid up.
Turning Off
Perform the following procedure to shutdown the Panel PC (for Windows 8):
1. Make sure you have closed any programs that are open on the Desktop. Start Screen
apps don’t need to be closed.
2. Open the Charms Bar by swiping your finger from the far right of the screen towards the
middle of the screen.
3. Tab on the Settings charm.
4. Tab on Power.
5. Tab on Shut Down.
6. Wait for Panel PC to power off.
Perform the following procedure to shutdown the Panel PC (for Windows 7):
1. Make sure you have closed any programs that are open on the Desktop.
2. Click the Start button , and then, in the lower-right corner of the Start menu, click Shut
down.
3. Or click the arrow next to the Shut down button for more options.
Note:
The computer will forcibly be turned off if the capacitive power key is pressed and held for 8
seconds or longer.
If the capacitive power key is pressed and held between 5 to 8 seconds, the computer will
enter preset custom power button action in OS. (ex: Do nothing, Ask me what to do,
Standby or Shut down)

6 W22IB3S Quick Start Guide
Using the Panel PC
HotTab Introduction
The HotTab mapping menu option allows user to change the function of the five physical touch
keys (brightness/volume keys, menu key, and function key).
Note:
For the Panel PC to work with the capacitive touch keys, the HotTab Utility has to be
installed and running the background. The power touch key is designed to work
independently, and would work without HotTab Utility.
Installing Touch Key HotTab Control Utility
In the driver CD, find the installation file “CapacitiveTouchKeys.rar” and execute to start the
installation. Follow the on-screen prompt with the installation wizard to finish the installation.
Note:
If the Panel PC is ordered with OS pre-installed, the HotTab Control Utility would have been
installed already.
HotTab Utility Icon shown in Windows System Tray:
Using the Capacitive Touch Key
As Windows starts up, HotTab starts and runs in the background. To display the HotTab control
utility, double click on the HotTab Utility icon in Windows System Tray.
There are 5 main menu options: +/- Key, Function Key, Menu Key, Touch Lock and Key Unlock.
Operations and functions on each menu option are explained in detail in the coming section.

W22IB3S Quick Start Guide 7
Setting the +/- Key (HotTab)
This HotTab +/- Key option allows users set the (+) and (-) touch keys’ functions. The +/- keys
can be set to control volume, brightness of the screen, and adjustment scale.
Volume Mode
Under this mode, the +/- Key controls Volume. (+) touch key is mapped to raise volume and (-)
touch key is mapped to lower volume.
To configure the key mapping, perform the following:
1. Open the HotTab utility by double clicking on the HotTab Utility icon in Windows System
Tray.
2. Tap on the +/- Key option.
3. Tap on Volume option.
Brightness Mode
Under this mode, the +/- Keys controls the screen Brightness. (+) touch key is mapped to raise
screen brightness and (-) touch key is mapped to lower screen brightness.
To configure the key mapping, perform the following:
1. Open the HotTab utility by double clicking on the HotTab Utility icon in Windows System
Tray.
2. Tap on the +/- Key option.

8 W22IB3S Quick Start Guide
3. Tap Brightness option.
Adjustment Scale Mode
Under this mode, the +/- Keys switches between user’s preset Brightness level. (+) touch key
sets the screen brightness to user’s preset maximum level and (-) touch key sets the screen
brightness to user’s preset minimum level. In other words, user can switch between two different
brightness levels quickly.
To configure the key mapping, perform the following:
1. Open the HotTab utility by double clicking on the HotTab Utility icon in Windows System
Tray.
2. Tap on the +/- Key option.
3. Tap Adjustment Scale option.
4. Drag the Maximum (+) slider or Minimum (-) slider to the right or left to set the desired
brightness level.

W22IB3S Quick Start Guide 9
Setting the Function Key (HotTab)
This HotTab Function Key option allows users set the function touch key’s function.
To configure function key mapping, perform the following:
1. Open the HotTab utility by double clicking on the HotTab Utility icon in Windows System
Tray.
2. Tap on the Function Key option.
3. Pick from list of preset applications by tapping on the application icons OR customize
which application to execute using the picker.
Using the Custom picker:
1. Tap the icon to reveal browser window
2. Navigate to the desired executable to map to function key
3. Tap on “Done”to save selection.

10 W22IB3S Quick Start Guide
To map the function key to another application:
1. Tap on the icon to remove connection to the original application, and pick again
tapping on icon.
Setting the Menu Key (HotTab)
This HotTab Menu Key option allows users set the touch key’s function. There are two
options available: Desktop Mode and Metro Mode.
Tapping on the Menu Key option toggles the Menu Key’s function between Desktop Mode and
Metro Mode (for Windows 8).
Desktop Mode
1. When the Menu Key is set to the Desktop mode, the Menu Key icon will have the following
icon: .
2. When the user taps the capacitive key while running an application, the display
screen will show the Desktop.

W22IB3S Quick Start Guide 11
Metro Mode (for Windows 8)
1. When the Menu Key is set to the Metro Mode, the Menu Key icon will have the following
icon:
2. When the user taps the capacitive key while running an application, the display
screen will show the Metro UI as shown:

12 W22IB3S Quick Start Guide
Setting the Touchscreen Lock (HotTab)
This HotTab Touch Lock option allows users to set the touchscreen lock function.
To lock the touchscreen, perform the following:
1. Open the HotTab utility by double clicking on the HotTab Utility icon in Windows System
Tray.
2. Tap on the Touch Lock option then the touchscreen will be locked.
To unlock the touchscreen, perform the following:
1. When the touchscreen is locked, touch the touchscreen, and the display screen will show
the touchscreen unlock slide bar.
2. Slide to unlock the touchscreen.
3. If users want to lock the touchscreen again, please follow the To lock the touchscreen
procedure again.

W22IB3S Quick Start Guide 13
Setting the Key Lock / UnLock (HotTab)
This HotTab Key Lock / UnLock option allows users to set the physical touch keys lock function.
Icon Status Description
Icon
Icon Description
Icon shown in white means the physical touch keys are currently unlocked.
The text below the icon shows the current status (Unlocked in this case).
Icon shown in orange means the physical touch keys are currently locked.
The text below the icon shows the current status (Locked in this case).
To lock the physical touch keys, perform the following:
1. Open the HotTab utility by double clicking on the HotTab Utility icon in Windows System
Tray.
2. Tap on the Key UnLock option then the physical touch keys will be locked, and the
icon will turn orange to show that lock is activated:

14 W22IB3S Quick Start Guide
To unlock the physical touch keys, perform the following:
1. Open the HotTab utility by double clicking on the HotTab Utility icon in Windows System
Tray.
2. Tap on the Key Lock option then the physical keys will be unlocked, and the icon
will turn white to show that lock is no longer activated:

W22IB3S Quick Start Guide 15