Winmate W10IB3S-PCH2AC-PoE S-Series User manual

Please read these instructions carefully before using this product, and save this manual for future use
10.1” S-Series HMI
W10IB3S-PCH2AC-PoE
W10IB3S-PCH2-PoE
Quick Start Guide
V1.2
For more information on this and
other Winmate products, please
visit our website at:
www.winmate.com
Document Part Number: 9154111I100A

- 2 -
Contents
1 INTRODUCTION - 7 -
1.1 Features - 7 -
1.2 Package Content - 8 -
1.3 Product Overview - 10 -
2 GETTING STARTED - 11 -
2.1 Turning On Your Device - 11 -
2.2 Operating the HMI Device - 12 -
2.3 Using HF RFID Reader - 15 -
2.4 Using Front Camera - 20 -
2.5 How to Enable Watchdog - 25 -
2.6 Using Recovery Wizard to Restore Computer - 27 -
2.7 Turning off Your Device - 28 -
3 Mounting - 29 -
3.1 Panel Mounting - 29 -
3.2 VESA Mounting - 30 -
3.3 Front Side Wall Mounting - 34 -
3.4 Glass Wall Mounting - 36 -
4 INSTALLATION - 37 -
4.1 Wiring Requirements - 37 -
4.2 Connecting to Other Devices - 38 -
5 SPECIFICATIONS - 41 -
5.1 HMI Device Specifications - 41 -
5.2 HF RFID Reader - 43 -
APPENDIX - 44 -
Appendix A: Cleaning the Monitor - 44 -
Appendix B: Winmate Software Development Kit - 45 -

- 3 -
FCC Statement
This device complies with part 15 FCC rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received
including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a
class "B" digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at him own expense.
European Union
Electromagnetic Compatibility Directive (2014/30/EU)
EN55024: 2010/ A1: 2015
oIEC61000-4-2: 2009
oIEC61000-4-3: 2006+A1: 2007+A2: 2010
oIEC61000-4-4: 2012
oIEC61000-4-5: 2014
oIEC61000-4-6: 2014
oIEC61000-4-8: 2010
oIEC61000-4-11: 2004
EN55032: 2012/AC:2013
EN61000-3-2:2014
EN61000-3-3:2013
Low Voltage Directive (2014/35/EU)
EN 60950-1:2006/A11:2009/A1:2010/A12:2011/
A2:2013
This equipment is in conformity with the requirement of the following EU
legislations and harmonized standards. Product also complies with the
Council directions.

- 4 -
Copyright Notice
No part of this document may be reproduced, copied, translated, or transmitted in
any form or by any means, electronic or mechanical, for any purpose, without the
prior written permission of the original manufacturer.
Trademark Acknowledgement
Brand and product names are trademarks or registered trademarks of their
respective owners.
Disclaimer
Winmate Inc. reserve the right to make changes, without notice, to any product,
including circuits and/or software described or contained in this manual in order
to improve design and/or performance. We assume no responsibility or liability for
the use of the described product(s) conveys no license or title under any patent,
copyright, or masks work rights to these products, and make no representations
or warranties that these products are free from patent, copyright, or mask work
right infringement, unless otherwise specified. Applications that are described in
this manual are for illustration purposes only. We make no representation or
guarantee that such application will be suitable for the specified use without
further testing or modification.
Warranty
Winmate Inc. warranty guarantees that each of its products will be free from
material and workmanship defects for a period of one year from the invoice date.
If the customer discovers a defect, we will, at his/her option, repair or replace the
defective product at no charge to the customer, provide it is returned during the
warranty period of one year, with transportation charges prepaid. The returned
product must be properly packaged in its original packaging to obtain warranty
service. If the serial number and the product shipping data differ by over 30 days,
the in-warranty service will be made according to the shipping date. In the serial
numbers the third and fourth two digits give the year of manufacture, and the fifth
digit means the month (e. g., with A for October, B for November and C for
December).
For example, the serial number 1W16Axxxxxxxx means October of year 2016.
Customer Service
We provide a service guide for any problem by the following steps: First, visit the
website of our distributor to find the update information about the product.
Second, contact with your distributor, sales representative, or our customer
service center for technical support if you need additional assistance.
You may need the following information ready before you call:
Product serial number
Software (OS, version, application software, etc.)
Description of complete problem
The exact wording of any error messages
In addition, free technical support is available from our engineers every business
day. We are always ready to give advice on application requirements or specific
information on the installation and operation of any of our products.

- 5 -
Safety Information
WARNING! / AVERTISSEMENT!
Always completely disconnect the power cord from your chassis
whenever you work with the hardware. Do not make connections
while the power is on. Sensitive electronic components can be
damaged by sudden power surges. Only experienced electronics
personnel should open the PC chassis.
Toujours débrancher le cordon d’alimentation du chassis lorsque
vous travaillez sur celui-ci. Ne pas brancher de connections
lorsque l’alimentation est présente. Des composantes
électroniques sensibles peuvent être endommagées par des sauts
d’alimentation. Seulement du personnel expérimenté devrait ouvrir
ces chassis.
CAUTION/ATTENTION
Always ground yourself to remove any static charge before
touching the CPU card. Modern electronic devices are very
sensitive to static electric charges. As a safety precaution, use a
grounding wrist strap at all times. Place all electronic components
in a static-dissipative surface or static-shielded bag when they are
not in the chassis.
Toujours verifier votre mise à la terre afin d’éliminer toute charge
statique avant de toucher la carte CPU. Les équipements
électroniques moderns sont très sensibles aux décharges
d’électricité statique. Toujours utiliser un bracelet de mise à la
terre comme précaution. Placer toutes les composantes
électroniques sur une surface conçue pour dissiper les charge, ou
dans un sac anti-statique lorsqu’elles ne sont pas dans le chassis.

- 7 -
1 INTRODUCTION
Congratulations on purchasing Winmate® 10.1” S-Series HMI.
Interactive and smart automation systems of intelligent buildings are
in a fast growing phase. Winmate multi-touch S-Series HMI is suitable
for home automation and room management systems. Flat surface is
easy-to-clean and delivers aesthetically pleasing look for any interior.
By connecting to centralized database, it can provide real time update
for booking status and available schedule, or perform as a
synchronous display in meetings.
S-Series HMI run on Intel® Celeron® N2930 processor and support
Windows 10 IoT, Windows Embedded 8.1 Industry Pro, Windows
Embedded 8Standard, Windows 7 Pro for Embedded Systems, and
Windows Embedded Standard 7–WS7P. For easy, quick and cost
effective network installations both models support PoE. These
models sealed with front IP 65 dust and water proof, and IP22 on the
back side. Optional HF RFID 13.56 MHz is useful for access control.
S-Series HMI has an exceptional feature - LED light bar. With the
help of red, green, blue and orange LED indicators you can see the
status of the machine or processes afar. It significantly reduces power
consumption by keeping the display turned off.
1.1 Features
Winmate® 10.1” S-Series HMI features:
10.1'' 1280 x 800 with Projected Capacitive Multi-Touch
Intel® Celeron® N2930 1.83GHz
PoE standard IEEE 802.3at (25 W)
Fanless cooling system and ultra-low power consumption
Dual Gigabit Ethernet
Front IP65 water and dust proof
RGB LED Status Light Bar indicators on both sides
Optional HF RFID Reader
Optional 2MP Front Camera
Stylish design for room booking, access control and room
information applications

- 8 -
1.2 Package Content
Carefully remove the box and unpack your device. Please check if all
the items listed below are inside your package. If any of these items
are missing or damaged contact us immediately.
Standard factory shipment list:
10.1” HMI Device
Quick Start Guide
(Hardcopy)
Driver CD & User
Manual
Varies by product
specifications
9154111I100A
IB32:
9171111I103M
AC Adapter
(12V/ 50W)
Power Cable
Terminal Block 3
Pin
922D050W12VA
Varies by country
94J602G030K0
VESA Mounting
Screws
82111E240400

- 9 -
Package may include optional accessories based on your order:
VESA Desk Stand
PCVS-V1
VESA Desk Stand
LA-100
VESA Wall Mount
Bracket
LA-106
99KK00A0000E
9B0000000128
9B0000000412
Front Side
Wall Mount Kit
PCFW-V1
Glass Wall Mount
Kit
Right: PCGM-V2L
Left: PCGM-V2L
99KK00A0000C
Right:
99KN00A00010
Left: 99KN00A00011

- 10 -
1.3 Product Overview
Unit: mm
Dimensions (W x L x H): 263.28 x 172 x 35.7 mm
*Digital I/O is an optional connector and may not be present in your
model.
** Power Device (PD): IEEE 802.3at (25 W)
***RGB LED Status Light Bar only available for the model number
W10IB3S-PCH2AC-PoE.
№
Description
№
Description
󰪦
Digital I/O (Optional)*
󰪫
RJ-45 (LAN/ PoE)**
󰪧
RJ-45 (LAN)
󰪬
2MP Front Camera (Optional)
󰪨
USB 2.0, USB 3.0
󰪭
HF RFID Reader (Optional)
󰪩
RS232/422/485
󰪮
LED Status Light Bar***
(Only for W10IB3S-PCH2AC-
PoE)
󰪪
12V DC Terminal Block
(Phoenix Type)
󰪯
1 Watt Speaker

- 11 -
2 GETTING STARTED
2.1 Turning On Your Device
Follow the following steps to turn on your device:
1. Connect HMI device to a thermal block (3-pin).
2. Connect the other side of the thermal block to the AC adapter.
3. Connect the AC adapter to the power cord.
4. Plug in the power cord to a working AC wall outlet. The device
will boot automatically.
CAUTION
Use only the AC adapter (12V/ 50W) included in your
package
(Rating: Output 4.2 A). Using other AC adapters may
damage the device.
ALTERNATING CURRENT
This product must be grounded. Use only a grounded
AC outlet. Install the additional PE ground wire if the
local installation regulations require it.

- 12 -
2.2 Operating the HMI Device
Winmate® 10.1” S-Series HMI support several versions of
Windows OS: Windows 10 IoT, Windows Embedded 8.1 Industry
Pro, Windows Embedded 8 Standard, Windows 7 Pro for
Embedded Systems, and Windows Embedded Standard 7–WS7P.
IMPORTANT:
The device is shipped with the OS System according to
your order. Contact us if you have any questions regarding
OS settings.
2.2.1 System Settings
2.2.1.1 Hot Tab Menu
1. Double-click the Hot Tab icon on the Windows desktop.
2. The Hot Tab main menu will appear on the screen as shown below.
NOTE:
RFID and LED Light Bar are optional features and may not be
present in your model.

- 13 -
2.2.1.2 Utilities
Utilities category allows automatically
changing orientation from landscape to
portrait mode or rotating the desktop to a
different degree as 0°, 90°, 180°, and 270°.
2.2.1.3 Brightness
Tap Brightness button to show current brightness level.
To reduce the brightness, drag by
touch to the left.
To enhance the brightness, drag
by touch to the right.
Tap Close to save changes and exit the interface.
2.2.1.4 Volume
Tap Volume button to show your current volume level.
To decrease the volume, drag
by touch to the left.
To increase the volume, drag by
touch to the right.
Tap Close to save changes and exit the interface.

- 14 -
2.2.1.5 LED Light Bar (Easy-Testing)
Notice that LED Light Bar is an optional feature for 10.1” S-Series
HMI and may not be present in your device. Tap Light Bar to access
the LED light bar control panel, and select Red / Green / Blue/
Orange color to be displayed on the LED Bar.
2.2.1.6 Performance
User can adjust the performance level of the HMI device. There are
four options available:
Extreme performance
Office Document
High performance
Power Saving
2.2.1.7 Touch Lock
To LOCK touch screen, double-click the Hot Tab icon on the
Windows desktop, and tap Touch Lock.
To UNLOCK the touch screen, tap button to the right.

- 15 -
2.3 Using HF RFID Reader
Notice that HF RFID Reader is an optional feature for 10.1” S-Series
HMI and may not be present in your device. HF RFID is commonly
used for ticketing, payment, and data transfer applications.
2.3.1 HF RFID Reader Location
The RFID Reader is located on the bottom right front side of the HMI
device. The COM Port setting in RFID Reader is “COM 14”
To enable the HF RFID Reader feature, perform the following
procedure:
1. Launch RF Scan application.
2. Tap on Connect, and the setting utility will show up as below:
3. Tap on the ON button.
To scan the card, bring it close to the right bottom front side of device
with RFID icon.
Tap on the Disconnect button to stop the connection with built-in HF
RFID reader.

- 16 -
2.3.2 Trigger Setting
Auto Scan
The default setting for RFID trigger is Auto Scan. Under this
setting, the RFID Reader will always be ready to scan tags.
1. When the RFID tag is detected from RFID antenna, the data
will be read automatically.
2. User can define the RFID scanning frequency from the drop-
down menu shown as below. The frequency can be from 1
second to 9 seconds.
Single Scan
User can also define the RFID Reader scanning as Single
Scan. Under this setting, the RFID Reader will be triggered only
when user click on “Send”.

- 17 -
2.4.3 Settings
Sound
The Sound check box defines whether a beep sound will come
with the data scanning.
Output
This setting defines the output type of the scanned data.
Two options are available:
Keyboard Wedge
Under this setting, the data scanned is sent like keyboard data.
The scanned data can be output directly to the demo area
below this window, or user can also open other utility, such as
Office Word or Notepad files, for data input.
Note: notice that the input method should support the scanned
character.
User can also tap on the Settings button for further details
settings.
Item
Description
Prefix
User can type in this field to define the characters
BEFORE the data scanned.
Suffix
User can type in this field to define the characters
AFTER the data scanned.
Append
Enter
The check box user can defines to append an “Enter”
which is followed by the characters.
Append
TAB
The check box user can defines to append an “TAB”
which is followed by the characters.
Regex
Filter
Press on “Presets…” button, user can define how
many characters to show after the data scanned.
Replace
User can define specific characters to be replaced
with preferred characters automatically. When the
characters defined in Regex Substitution is
scanned, the data will be replaced with the one filled
in Replace with.
Reset to
default
User can remove all the set up and back to default
mode.

- 18 -
SDK
For users following SDK for software porting, the scanned data
can also be output with the format needed.
2.4.4 RFID Output Settings
Select RFID Output Type
The default setting for built-in HF RFID Reader is to Read UID. For
some applications, user might need to read or write further block data;
the drop-down menu under this section can do this change.
Demo Area

- 19 -
2.4.2 Writing Mode
Refer to the RFID Porting Guide SDK to configure Writing Mode
parameters.

- 20 -
2.4 Using Front Camera
Notice that 2MP Front Camera is an optional feature for 10.1” S-
Series HMI and may not be present in your device.
NOTE:
You camera screen may differ from the pictures in thus
user manual.
2.4.1 Opening the Camera
Perform one of the following to open the camera:
1. Press the F1 key.
2. Tap then double-tap to display the HotTab screen.
Select Camera.
The Camera Screen