Winners Only T1-QR4257-B User manual

TBS-11388-PGNWC MADE IN MALAYSIA
Page 1 of 3
PARTS LIST
PART NO FIGURE DESCRIPTION QTY
T1-QR4257-T-B-01
T1-QR4257-B
T1-QR4257-T-B-13
T1-QR4257-T-B-13
T1-QR4257-T-B-18
T1-QR4257-T-B-19
T1-QR4257-T-B-08
T1-QR4257-T-B-08
T1-QR4257-T-B-07
T1-QR4257-T-B-07
IMPORTANT NOTE : Please keep all hardware parts out of the reach of children.
Pedestal Stand
Pedestal Leg
1 pce
1 pce
1 pce
Mounting Plate
Side Panel
Table Top
Hardware Pack
4 pcs
1 pce
2 pcs
SOLID TOP B'FLY LEAF PED. TABLE

MADE IN MALAYSIA
TBS-11388-PGNWC Page 2 of 3
ASSEMBLY :
STEP 1
Reminders :
Two people are needed for assembly.
Use only hardware supplied.
Do not over tighten bolts.
This item may require periodic tightening.
HARDWARE PART :
Hex Nut
4 pcs
Allen Key
1pce
T1-QR4257-B
SOLID TOP B'FLY LEAF PED. TABLE
STEP 2
JCBC Bolt
4 pcs
Flat Washer
(Large)
12 pcs
Wrench
1 pce
Lock Washer
(Large)
12 pcs
Flat Washer
(Small)
8 pcs
Lock Washer
(Small)
8 pcs
Hex Nut
Lock Washer (Large)
Flat Washer (Large)
Pedestal
Leg
Level Glide
Wrench
1.1- Turn the pedestal upside down. Attach legs by inserting hanger bolts through pre-drilled holes on the
combination pedestal.shown in Fig.1
Base Assembly
Fig.1
2.1- Position the table top upside down on a smooth, protective surface such as carpet. Remove and
discard the temporary wood strip .Install the side panel and mounting plate by using the supply hardware
as shown on Fig.2
Mounting Plate
Side Panel
Lock Washer (Small)
Lock Washer (Small)
Allen Key
Allen Key
JCBC Bolt
JCBC Bolt
Flat Washer (Small)
Flat Washer (Small)
Fig.2
Must Remove all 4 Cleats
R
E
M
O
V
E
R
E
M
O
V
E

MADE IN MALAYSIA
TBS-11388-PGNWC Page 3 of 3
CARE INSTRUCTION
~ Be sure to use the same type of polish consistenly.
Your furniture will appear cloudy or streaky if oil
based or wax based polishes are interchanged.
~ Spray your furniture surface evenly. Wipe in a
circular motion with a soft clean cloth.
IMPORTANT NOTE :
~ Please keep all hardware out of the reach of
children.
ASSEMBLY :
T1-QR4257-B
SOLID TOP TRESTLE BASE COUNTER HT. TABLE
Lock Washer (Large)
Flat Washer (Large)
Wrench
Hex Nut
STEP 3
3.1- Unlock the metal catches from underneath the table Top and pull the table from both ends. Attached base assembly to the
table top mounting plate using the supply hardware as shown on Fig.3
UnLock
Metal Catches
4.1-Lift both leaves from the compartment.
4.2-Flip up the aprons and unfold leaf and place the leaf on the Table Top surface carefully.
STEP 4
Flip up Apron
STEP 5
5.1-Push Table Top from both ends to close.Lock the metal catches underneath the table.
Level Glide
Lock
Metal Catches