Wolf Icbmm15t/s User manual

MULTIFUNCTION COOKTOP

INSTALLATION GUIDE

English

Product Information

Important product information including the model and

serial number are listed on the product rating plate. The

rating plate is located on the bottom of the cooktop. Refer

to the illustration below.

If service is necessary, contact Wolf factory certied service

with the model and serial number.

MULTIFUNCTION COOKTOP

Contents

2Multifunction Cooktop

3Specications

4Installation

5Troubleshooting

Features and specications are subject to change at any

time without notice.

Important Note

To ensure this product is installed and operated as safely

and efciently as possible, take note of the following types

of highlighted information throughout this guide:

IMPORTANT NOTE highlights information that is especially

important.

CAUTION indicates a situation where minor injury or product

damage may occur if instructions are not followed.

WARNING states a hazard that may cause serious injury or

death if precautions are not followed.

IMPORTANT NOTE: Save these instructions for the local

electrical inspector.

WARNING

FOR AUSTRALIA ONLY:

•Do not use or store ammable materials in the

appliance storage drawer or near this appliance.

•Do not spray aerosols in the vicinity of this appli-

ance while in operation.

•Do not modify this appliance.

•This appliance is for indoor use only.

•A ventilation unit is suggested for use with this

appliance. Refer to the instructions shipped with the

ventilation unit for proper clearances.

•If the information in the guide is not followed, a re

or explosion may result, causing property damage,

personal injury or death.

•This appliance must be properly installed and

serviced by a qualied installer, service agency or

gas supplier and grounded (earthed) by a qualied

technician.

Rating plate location.

RATING PLATE

subzero-wolf.com.au

Gas Supply

Installation must conform with local codes or, in the absence

of local codes, with the National Fuel Gas Code.

Locate the gas supply as shown in the illustration on the

following page.

The cooktop is equipped for use with natural or liquid pro-

pane (LP) gas. The product rating plate has information on

the type of gas that should be used. For rating plate loca-

tion, refer to the illustration below. If this information does

not agree with the type of gas available, check with the local

gas supplier.

Prior to installation, ensure that the local distribution condi-

tions (nature of the gas and gas pressure) and the adjust-

ment of the appliance are compatible. The adjustment

conditions for this appliance are stated on the label (or

rating plate). The data plate can be found on the underside

of the cooktop.

This appliance is not connected to a combustion prod-

ucts evacuation device. It shall be installed and connected

in accordance with current installation regulations. Par-

ticular attention shall be given to the relevant requirements

regarding ventilation.

The cooktop must be connected to a regulated gas supply.

The supply line must be equipped with an approved external

gas shut-off valve located near the cooktop in an accessible

location. Do not block access to the shut-off valve. Refer to

the illustration below.

SHUT-OFF VALVE

OPEN POSITION

GAS SUPPLYTO APPLIANCE

Rating plate location. Gas shut-off valve.

RATING PLATE

Installation Requirements

A minimum 51 mm is required from the bottom of the

cooktop to combustible materials. If the cooktop is installed

above an oven, a minimum of 6 mm is required between

units. Refer to the illustration on page 6 for additional

minimum clearances.

WARNING

Failure to locate the cooktop without proper clearances

will result in a re hazard.

SPECIFICATIONS

Electrical

Installation must comply with all applicable electrical codes

and be properly grounded (earthed).

Locate the electrical supply as shown in the illustration on

page 6. A separate circuit, servicing only this appliance is

required. A ground fault circuit interrupter (GFCI) is not rec-

ommended and may cause interruption of operation.

When multiple cooktops or modules are installed side by

side, each unit must have its own separate recommended

electrical circuit.

ELECTRICAL REQUIREMENTS

Electrical Supply 220-240 V AC, 50/60 Hz

Service 10 amp dedicated circuit

Receptacle grounding-type (earthed)

Power Cord 1.8 m

IMPORTANT NOTE: Connection of this appliance should be

through a fused connection unit or a suitable isolator, which

complies with national and local safety regulations. The

on/off switch should be easily accessible after the appli-

ance has been installed. If the switch is not accessible after

installation (depending on country) an additional means of

disconnection must be provided for all poles of the power

supply. When switched off there must be an all pole contact

gap of 3 mm in the isolator switch. This 3 mm contact dis-

connect gap must apply to any isolator switch, fuses and/or

relays according to EN60335.

WARNING

FOR AUSTRALIA ONLY:

This appliance is supplied with a cord and can be hard

wired to a terminal box or plug. Do not remove the

ground (earthed) plug.

A gas supply line of 19 mm rigid pipe must be provided to

the cooktop. If local codes permit, a certied, .9 m long,

13mm or 19 mm ID exible metal appliance connector is

recommended to connect the units 1/2" NPT (or ISO 7/1-14)

male inlet to the gas supply line. Pipe joint compounds, suit-

able for use with natural or LP gas should be used.

The appliance and its shut-off valve must be disconnected

from the gas supply piping system during any pressure

testing of the system at test pressures in excess of 3.5 kPa.

The appliance must be isolated from the gas supply piping

system by closing its individual manual shut-off valve during

any pressure testing of the system at test pressures equal to

or less than 3.5 kPa.

Wolf natural gas cooktops will function up to 3124 m in

altitude without adjustment and LP gas cooktops will func-

tion up to 2621 m. If the installation exceeds these eleva-

tions, contact your authorized Wolf dealer for a high altitude

conversion kit.

WARNING

FOR AUSTRALIA ONLY:

•The appliance must be connected to a regulated

gas supply with an approved regulator.

•This appliance can be installed using a 10 mm diam-

eter 1000 mm exible hose assembly complying

with AS/NZS 1869, Class ‘B. Maximum working

pressure 14 kPa, ambient temperature: -20°C to

125°C and AGA approved. The hose is not provided

with the appliance.

•If installing with a exible hose, verify the hose is not

kinked or can be damaged. If installing above and

oven, use a hose that will not be damaged by the

heat from the oven.

•Failure to locate this appliance without proper clear-

ances will result in a re hazard.

•Adjust the inlet pressure regulator until the test point

pressure is 1 kPa for NGand 2.75 kPa for Propane

with 2 semi rapid burners set at maximum rate.

Apply the self-adhesive data plate provided. It is the

responsibility of the installer to test the operation of

the cooktop upon completion and leave this manual

with the product.

P (BROWN)

N (BLUE)

E (GREEN/YELLOW)

English

SPECIFICATIONS

FRONT VIEWSIDE VIEW

COUNTERTOP CUT-OUT

NOTE: Shaded area above countertop indicates minimum clearance to combustible surfaces,

combustible materials cannot be located within this area.

The height from the benchtop to the top of the trivert (Pan Support) is 34mm.

330

mm 457

178

E G

127

ELECTRICAL

AND GAS FLOOR

LOCATION

650

356 mm 495 mm

64 mm

Multifunction Cooktop

INSTALLATION

Gas Supply

GAS RATING

MODEL

TOTAL HEAT

OUTPUT

GAS

UNITS

APPLIANCE

CATEGORY

TYPES AND

PRESSURE (mbar) COUNTRY OF DESTINATION

ICBMM15T/S

ICBMM15TF/S 8 kW

I2H G20 at 20 AT, CZ, DK, FI, GR, HR, IS, IE, IT, PT, SK, SI, ES, SE, CH,

TR, GB, EE, LV, LT, NO, RO

I2E G20 at 20 DE, LU

I2E+ G20 at 20/25 BE, FR

ICBMM15T/S/LP

ICBMM15TF/S/LP 572 g/h I3P G31 at 37 CH, CZ, DE, IT, ES, FI, GR, GB, NL, SK, IE, SI, RO, PL,

LV, LT

GAS RATING—AUSTRALIA ONLY

MODEL GAS TYPE GAS PRESSURE MJ/h INJECTOR

ICBMM15TF/S Natural 1.0 kPa 25 2.30 mm

LP 2.75 kPa 25 1.34 mm

Note: Commisioning Procccedure is with Wok burner set to maxium setting .

subzero-wolf.com.au

Gas Supply Connection

All connections to the gas piping must be wrench-tightened.

Do not overtighten or allow pipes to turn when tightening.

1If a exible metal connector is being used, verify it is not

kinked, then attach the gas supply line to the regulator

on the cooktop.

2Open the valve and check for leaks by placing a liquid

detergent solution onto all gas connections. Bubbles

around connections indicate a gas leak. If a leak

appears, close the shut-off valve and adjust connections.

Troubleshooting

IMPORTANT NOTE: If the cooktop does not operate prop-

erly, follow these troubleshooting steps:

•Verify electrical power is supplied to the cooktop.

•Verify the gas supply shut-off valve is in the open

position.

•If the cooktop does not operate properly, contact Wolf

factory certied service. Do not attempt to repair the

cooktop. Wolf is not responsible for service required to

correct a faulty installation.

INSTALLATION

Cooktop Installation

Remove cooktop and components from the shipping

package and recycle packing materials.

1Lower the cooktop into the countertop cut-out. Center

the cooktop in the opening with the front edge aligned

parallel to the front edge of the countertop. Using a

pencil, outline the rear edge of the cooktop on the coun-

tertop. Remove the cooktop.

2Apply the foam strip to the perimeter of the countertop

opening. Refer to the illustration below. Do not seal the

cooktop to the countertop.

3Insert the cooktop into the opening, aligning the rear

edge with the pencil line. Verify the cooktop is aligned

with the front edge of the countertop.

4To attach brackets to the sides of the cooktop, insert

clips into the side punchouts and press down. Install

clamping screws into the brackets and tighten until

screws contact the underside of the countertop. Do not

overtighten. Refer to the illustration below.

FOAM STRIP

COUNTERTOP

BRACKET

CLIP

CLAMPING

SCREW

Cooktop installation.

Sub-Zero, Sub-Zero & Design, Sub-Zero & Snowake Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, Wolf, Wolf & Design, Wolf Gourmet, W & Design, red colored knobs, Cove, and Cove & Design, are registered trademarks and service marks of Sub-Zero Group, Inc. and its subsidiaries.