Wolf Pro Wall Ventilation hoods User manual

Pro Wall Ventilation Hoods
INSTALLATI N GUIDE

mportant Note
To ensure the safe and efficient use of Wolf equipment,
please take note of the following types of highlighted
information throughout this guide:
IMP RTANT N TE highlights information that is especially
important.
CAUTI N signals a situation where minor injury or product
damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
Contents
Wolf Pro Wall Ventilation Hoods . . . . . . . . . . . . . . . . . . 3
Installation Considerations . . . . . . . . . . . . . . . . . . . . . . 4
Pro Wall Hood Specifications . . . . . . . . . . . . . . . . . . . . 5
Pro Wall Hood Installation . . . . . . . . . . . . . . . . . . . . . 10
ServiceInformation...........................18
Features and specifications are subject to change at any time
without notice. Visit wolfappliance.com/specs for the most
up-to-date information.
IMP RTANT N TE: Throughout this guide, dimensions in
parentheses are millimeters unless otherwise specified.

Wolf Pro Wall Ventilation Hoods 3
wolfappliance.com/specs
Pro Wall Hood nstallation
IMP RTANT N TE: This installation must be completed
by a qualified installer or Wolf factory certified service.
Read this entire installation guide and blower installation
instructions prior to installation and save for the local
inspector’s reference. The homeowner should keep this
installation guide for future reference.
This appliance must be installed in accordance with
National Electrical Codes, as well as all state, municipal
and local codes. The correct voltage, frequency and
amperage must be supplied to the appliance from a dedi-
cated, grounded circuit which is protected by a properly
sized circuit breaker or time delay fuse. The proper
voltage, frequency and amperage ratings are listed on the
product rating plate.
Record the model and serial numbers before installing the
ventilation hood. Both numbers are listed on the product
rating plate, located inside the left wall of the hood. Refer
to the illustration below.
Wolf Pro Ventilation Hood
Model Number
Serial Number
Location of rating plate
(inside hood).
RAT NG PLATE

MPORTANT NSTRUCT ONS
T REDUCE THE RISK F FIRE, ELECTRIC
SH CK R INJURY, BSERVE THE F LL WING:
• nstallation work and electrical wiring must be
done by qualified person(s) in accordance with all
applicable codes and standards, including fire-rated
construction.
• Two installers are recommended due to the size and
weight of the pro ventilation hood.
• nstall the pro ventilation hood only with a blower
manufactured by Wolf.
• When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
• Ducted fans must always be vented to the outdoors.
nstallation Considerations 4
nstallation Considerations
Wolf pro ventilation hoods are recommended for use with
all Wolf cooking appliances.
•For best performance in wall applications, a 27" (686)
deep hood is recommended for models with a char-
broiler or griddle.
•Proper installation is the responsibility of the installer.
Product failure due to improper installation is not
covered under the Wolf warranty. Refer to the Wolf pro
ventilation hoods use & care guide for warranty details,
or visit the contact & support section of our website,
wolfappliance.com.
•Warranty service must be performed by Wolf factory
certified service. Wolf is not responsible for service
required to correct a faulty installation.
BL WER ASSEMBLIES
Wolf pro ventilation hoods are shipped without a blower
assembly. nternal, in-line and remote blowers are avail-
able through your authorized Wolf dealer. For local dealer
information, visit the find a showroom section of our
website, wolfappliance.com.
Blower size is dependant on the size of the cooking
surface, volume of air being moved and length of the duct
run. Refer to ventilation recommendations in the Wolf
design guide.
n-line and remote blowers require Romex® (not provided)
from the blower to the ventilation hood. For blower instal-
lation, refer to specific instructions provided with each
blower. Additional information can also be found on our
website, wolfappliance.com.
To reduce the risk of fire and properly exhaust air,
be certain to duct air outside. Do not vent exhaust
air into spaces within walls or ceilings or into attics,
crawl spaces or garages.

Pro Wall Hood Specifications 5
wolfappliance.com/specs
30" (762), 36" (914), 42" (1067)
AND 48" (1219) WIDTHS
10" (254)
OVERALL
HEIGHT 4" (102)
22" (559)
OVERALL DEPTH
12"
(305)
Overall Dimensions
L W-PR FILE WALL H DS
30" (762), 36" (914), 42" (1067), 48" (1219)
54" (1372), 60" (1524) AND 66" (1676) WIDTHS
18" (457)
OVERALL
HEIGHT
4" (102)
24" (610)
OVERALL DEPTH
12"
(305)
24" (610) DEEP WALL H DS
30" (762), 36" (914), 42" (1067), 48" (1219)
54" (1372), 60" (1524) AND 66" (1676) WIDTHS
27" (686)
OVERALL DEPTH
12"
(305)
18" (457)
OVERALL
HEIGHT
4" (102)
27" (686) DEEP WALL H DS

Pro Wall Hood Specifications 6
E
6"
(152)
5"
(127)
LOCATION OF ELECTRICAL
WIDTH OF HOOD
30" (762) TO 36" (914)
TO COUNTERTOP
10" (254)
HEIGHT
OF HOOD
22" (559)
DEPTH OF HOOD
SIDE VIEW
nstallation
L W-PR FILE WALL H DS
E
6"
(152)
5"
(127)
LOCATION OF ELECTRICAL
WIDTH OF HOOD
30" (762) TO 36" (914)
TO COUNTERTOP
18" (457)
HEIGHT
OF HOOD
24" (610) OR
27" (686)
DEPTH OF HOOD
SIDE VIEW
24" AND 27" DEEP WALL H DS

Pro Wall Hood Specifications 7
wolfappliance.com/specs
nstallation Options
H RIZ NTAL DISCHARGE
Pro low-profile wall hoods have an adjustable discharge.
Pro 24" (610) and 27" (686) deep wall hoods have a vertical
discharge. A horizontal discharge kit is available through
your authorized Wolf dealer. For local dealer information,
visit the find a showroom section of our website,
wolfappliance.com.
RECIRCULATING INSTALLATI N
Pro wall hoods, 30" (762) and 36" (914) wide, with an
internal blower (600 CFM or less), can be used in a non-
ducted application with a recirculating filter. n this installa-
tion, kitchen air is purified through filters and returned as
clean air into the room. A recirculation kit available through
your authorized Wolf dealer is required. For local dealer
information, visit the find a showroom section of our
website, wolfappliance.com.
DUCT C VER
Optional stainless steel duct covers, in multiple heights,
are available through your authorized Wolf dealer. Duct
covers must be attached to ventilation hood prior to hood
installation. For local dealer information, visit the find a
showroom section of our website, wolfappliance.com.
BACKSPLASH
Optional stainless steel backsplashes, in widths to match
all pro wall hoods, are available through your authorized
Wolf dealer. Backsplash must be installed prior to hood
installation. For local dealer information, visit the find a
showroom section of our website, wolfappliance.com.
Electrical Requirements
Wolf pro ventilation hoods require a separate, grounded
120 V AC, 60 Hz power supply. The service should have its
own 15 amp circuit breaker. Locate the electrical supply
within the shaded area shown in the installation illustration
on the previous page.
n-line and remote blowers require Romex®(not provided)
from the blower to the ventilation hood.
IMP RTANT N TE: You must follow all National Electrical
Code regulations. n addition, be aware of local codes and
ordinances when installing your service.
Risk of electrical shock. This hood must be properly
grounded. Electrical service for the hood must be
installed by a qualified electrician in accordance with
all applicable national and local electrical codes.

Pro Wall Hood Specifications 8
Discharge Specifications
L W-PR FILE WALL H DS
The illustrations provide dimensions for discharge options
for low-profile wall hoods. These dimensions are critical
for proper installation. Dimension A in the illustrations will
vary with the width of the hood. Refer to the chart below.
Low-Profile Wall Hoods
WIDTH F H D A
30" (762) 143/4"(375)
36" (914) 173/4"(451)
42" (1067)* 203/4"(527)
48" (1219)* 233/4"(603)
*500 CFM blower not available for these hood widths.
A
TO
CENTER OF
TRANSITION
11/2"(38)
2" (51)
TO CENTER
OF TRANSITION
Horizontal discharge.
9"
(229)
55/8"(143)
TO CENTER
OF TRANSITION
A
TO
CENTER OF
TRANSITION
Vertical discharge with accessory transition.
11/2"(38)
25/8"(60)
TO CENTER
OF TRANSITION
A
TO
CENTER OF
TRANSITION
Vertical discharge.
L W-PR FILE WALL H DS DISCHARGE PTI NS
DISCHARGE
CUT-OUT
31/4"
(83)
14"
(356)
Cut-out without transition.

Pro Wall Hood Specifications 9
wolfappliance.com/specs
Discharge Specifications
24" AND 27" DEEP WALL H DS
The illustration below provides dimensions for vertical
discharge for 24" (610) and 27" (686) deep wall hoods.
These dimensions are critical for proper installation.
Dimension A in the illustration will vary with the width of
the hood. Refer to the chart below.
An optional horizontal discharge kit is available through
your authorized Wolf dealer. For local dealer information,
visit the find a showroom section of our website,
wolfappliance.com.
24" and 27" Deep Wall Hoods
WIDTH F H D A
30" (762) 143/4"(375)
36" (914) 173/4"(451)
42" (1067)* 203/4"(527)
48" (1219)* 233/4"(603)
54" (1372)* 263/4"(679)
60" (1524)* 293/4"(756)
66" (1676)* 323/4"(832)
55/8"
(143)
2" (54)
A
24" and 27" deep wall hoods—
vertical discharge.

Pro Wall Hood nstallation 10
nstall Ductwork
10" (254) round, rigid metal duct is recommended for pro
ventilation hoods.
A straight, short run is most effective and will ensure
proper operation. For best results, duct run should not
exceed 50' (15 m). For runs exceeding 50' (15 m), a higher
CFM blower may be required to maintain proper air flow
and performance. A remote blower installed on a short
duct run may increase the potential for noise.
nternal and in-line blowers require a roof or wall cap (not
provided). Connect ductwork to the cap and work back
towards the ventilation hood. Use sheet metal screws and
aluminum tape or high temperature duct tape to seal joints
between ductwork sections.
To reduce the risk of fire, use only metal ductwork.
All pro ventilation hoods include a backdraft damper in the
transition assembly. Local codes may require the use of an
additional backdraft and/or make-up air damper. Contact
your local HVAC professional for specific requirements.
Backdraft and make-up air dampers are available through
your authorized Wolf dealer. For local dealer information,
visit the find a showroom section of our website,
wolfappliance.com.