Wolf WWDFRONT/B User manual

USE & CARE GUIDE
Warming Drawers

Important Note
To ensure the safe and efficient use of Wolf equipment,
please take note of the following types of highlighted
information throughout this guide:
I PORTANT NOTE highlights information that is especially
important.
CAUTION signals a situation where minor injury or product
damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
Contents
WolfWarmingDrawers .........................3
SafetyInstructions ............................4
Warming Drawer Features . . . . . . . . . . . . . . . . . . . . . . 6
Warming Drawer Operation . . . . . . . . . . . . . . . . . . . . . 7
WarmingDrawerCare.........................12
ServiceInformation...........................13
WolfWarranties..............................14
Features and specifications are subject to change at any time
without notice. Visit our website, wolfappliance.com for the
most up-to-date information.
I PORTANT NOTE: Throughout this guide, dimensions in
parentheses are millimeters unless otherwise specified.

If service should become necessary, you will need the
model and serial numbers of the warming drawer. Both
numbers are listed on the product rating plate, located on
the left front floor area of the inner cabinet. To access the
rating plate, the drawer must be fully open. Refer to the
illustration below.
I PORTANT NOTE: The warming drawer must be installed
with a Wolf stainless steel or integrated drawer front.
Wolf Warming Drawers 3
wolfappliance.com
Thank You
Your purchase of a Wolf warming drawer attests to the
importance you place upon the quality and performance of
your cooking equipment. We understand this importance
and have designed and built your warming drawer with
quality materials and workmanship to give you years of
dependable service.
Before you begin using your warming drawer, please take
some time to read this use & care guide. It will be to your
benefit to familiarize yourself with the safety practices,
features, operation and care recommendations of the Wolf
warming drawer.
Your Wolf warming drawer is protected by a warranty that
is one of the finest in the industry. Take a moment to read
the warranty statement at the end of this guide and refer
to it should service become necessary.
Location of rating plate.
RATING
PLATE

Safety Instructions 4
IMPORTANT INSTRUCTIONS
I PORTANT NOTE: Read all safety instructions before
using this appliance.
• Read this use & care guide carefully before using
your new warming drawer to reduce the risk of fire,
electric shock or injury to persons.
• Ensure proper installation and servicing. This appli-
ance must be properly installed and grounded by a
qualified technician. ave the installer show you the
location of the circuit breaker or fuse so that you
know where to turn off power.
• Warranty service must be performed by Wolf factory
certified service.
• Before performing any service, unplug or disconnect
the power supply for the warming drawer by switch-
ing off the circuit breaker or removing the fuse.
GENERAL SAFETY REQUIRE ENTS
• Ensure that towels are stacked only as high as the
sides of the drawer pan. Any higher may result in
discoloration of the towels.
• The purpose of the warming drawer is to hold hot
cooked foods at serving temperature and proof
yeast dough. Cold food cannot be heated thoroughly
or cooked in the warming drawer.
• Make sure the warming drawer is securely installed
in a firmly attached cabinet.
• Use care when opening the warming drawer.
Partially open the warming drawer and let warm air
escape prior to removing or replacing food.
• Always place the rack in the desired location while
the warming drawer is cool.
• Always use dry pot holders when removing items
from the warming drawer. Wet or damp pot holders
can cause burns. Do not use a towel or bulky cloth
in place of pot holders.

• Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
• Do not touch the heating element or the interior
surface of the warming drawer. These surfaces may
be hot enough to burn. The inside surfaces of the
warming drawer may be hot when opened.
• Do not heat unopened food containers. Pressure
could build up and the container could burst and
cause serious injury.
• Do not use aluminum foil to line the warming drawer.
This may cause damage to interior surfaces of the
warming drawer.
• Do not overfill the warming drawer. This may lead to
difficulty in opening or closing the drawer, as well as
items falling out of the drawer or behind the drawer.
Safety Instructions 5
wolfappliance.com
IMPORTANT INSTRUCTIONS
GENERAL SAFETY REQUIRE ENTS
• Do not operate the warming drawer if the front panel
has not been installed.
• Do not repair or replace any part of the warming
drawer unless specifically recommended in literature
accompanying this appliance. All service should be
referred to Wolf factory certified service.
• Do not leave children alone or unattended in the area
when the warming drawer is in use. Never allow
children to sit, stand or hide in the appliance. Do not
let children play with the warming drawer.
• Never leave the warming drawer open when you are
not attending to the warming drawer.
• Never use the warming drawer or other appliances
for warming or heating the room.
• Do not wear loose fitting or hanging garments while
using this appliance.
• Do not place more than 75 lbs (34 kg) into the
warming drawer. Do not use the warming drawer to dry paper
products. If overheated, paper products can catch
fire.

Warming Drawer Features 6
Warming Drawer Features
•Model WWD30 can be installed in a standard or flush
inset application.
•Model WWD30O is CSA approved for outdoor
applications.
•UL approved for warming towels.
•Crafted of heavy-duty stainless steel.
•idden electronic touch controls for sleek appearance.
•Temperature control range of 80°F (25°C) to 200°F (95°C).
•Four preset temperatures: high 200°F (95°C), medium
160°F (70°C), low 120°F (50°C) and proof 85°F (30°C).
•Programmable automatic shutoff up to four hours.
•Fan assist for even heat distribution.
•Fast preheat times.
•Rack for stacking food.
•Three ball-bearing drawer glides for smooth, full
extension.
•Removable stainless steel drawer for easy cleaning.
•CSA certified for US and Canada.
•Two and five year residential warranty—exclusions
apply, see warranty at the end of this guide.
OPTIONAL ACCESSORIES
Optional accessories are available through your authorized
Wolf dealer. For local dealer information, visit the find a
showroom section of our website, wolfappliance.com.
•Stainless steel drawer fronts to match style of Wolf
ovens and ranges.
•2" (51) thick stainless steel drawer fronts for installation
below sealed burner rangetop.
•Integrated drawer front for custom wood applica-
tions—panel can exceed 30" (762) width.
•Six-piece container set with lids.
•Stainless steel tubular and pro handles.
idden touch
control panel
Stainless steel
drawer pan
Drawer front
options
Ball-bearing
drawer glides
Removable rack
for stacking food
This appliance is certified by Star-K to meet
strict religious regulations in conjunction with
specific instructions found on www.star-k.org.
WAR ING DRAWER
Model WWD30 shown with L series drawer front.

Warming Drawer Operation 7
wolfappliance.com
Control panel.
ON/OFFLCD Display Preset
temperatures
Variable
temperature
(UP/DOWN)
Automatic
shut-off timer
(UP/DOWN)
Electronic Controls
The electronic touch control panel is hidden when the
warming drawer is closed. With the warming drawer open,
the controls can be accessed at the top of the drawer just
behind the drawer front.
PRESETS
Your warming drawer features four preset temperature
settings; PROOF, LOW, MED and IG . Using the
PRESETS eliminates the need to manually set the temper-
ature and time.
SETTING TE PERATURE
1) Touch POWER ON/OFF.
2) Touch one of the PRESETS; PROOF, LOW, MED or
IG or touch the TEMP UP or DOWN arrow pad.
Touch the UP arrow to increase the temperature and
the DOWN arrow to decrease the temperature. Two
seconds after selecting the temperature, the ON indi-
cator will illuminate and an audible chime will sound
indicating that the warming drawer is on.
I PORTANT NOTE: One of the PRESETS or the TEMP UP
or DOWN arrow pad must be touched within 20 seconds
of turning the unit on, or it will automatically shut off.
PREHEAT
During preheat, the temperature read-out in the LCD
display alternates between the setpoint and the actual
temperature. The word ‘Lo’ will appear in the display until
the temperature reaches 85°F (30°C). An audible chime will
sound to signal when preheat is complete.
AUTO ATIC SHUT-OFF
Your Wolf warming drawer has a preset automatic shut-off
time of four hours. The time interval of the automatic shut-
off can be adjusted from one minute to 24 hours.
SETTING AUTO ATIC SHUT-OFF
1) Warming drawer must be OFF.
2) Touch POWER ON/OFF.
3) Touch one of the PRESETS; PROOF, LOW, MED or
IG or touch the TEMP UP or DOWN arrow pad.
Touch the UP arrow to increase the temperature and
the DOWN arrow to decrease the temperature.
4) Touch and hold the TIMER UP arrow to increase the
shut-off time or the DOWN arrow to decrease the
shut-off time.
5) The word TIMER will illuminate and the automatic
shut-off time will appear in the display.
Preset Temperature Settings
PROOF 85°F (30°C)
LOW 120°F (50°C)
MED 160°F (70°C)
IG 200°F (95°C)

Sabbath Mode
Sabbath mode is for certain religious observances where
some warming drawer functions need to be turned off. In
Sabbath mode, the automatic shut-off feature is disabled,
allowing the warming drawer to operate continuously.
SETTING SABBATH ODE
1) Warming drawer must be OFF.
2) Touch and hold POWER ON/OFF for 5 seconds. The
word ‘Sab’ will flash in the display after 5 seconds.
3) While ‘Sab’ is flashing, select one of the PRESETS or
set the temperature with the TEMP UP or DOWN arrow
pads. Touch the UP arrow to increase the temperature
and the DOWN arrow to decrease the temperature.
Two chimes will signify that the Sabbath mode has
been initiated.
4) In Sabbath mode, the warming drawer will operate
continuously until POWER ON/OFF is touched. The
word ON will remain illuminated in the display all the
while the unit is in Sabbath mode. No other read-outs
will appear in the display.
5) Touch POWER ON/OFF to shut off the warming drawer
and exit Sabbath mode.
Warming Drawer Operation 8
Electronic Controls
PRESET PROGRA ING
Preset temperatures and time settings can be adjusted for
the PROOF, LOW, MED and IG PRESETS.
The PROOF temperature range is from 80°F (25°C) to
110°F (40°C). The LOW, MED and IG PRESETS can be
adjusted from 80°F (25°C) to 200°F (95°C).
ADJUSTING PRESET TE PERATURE AND TI E
1) Warming drawer must be OFF.
2) Touch POWER ON/OFF.
3) Touch and hold the desired PRESET, PROOF, LOW,
MED or IG for 5 seconds. The word TIMER will illu-
minate and ‘4:00’ will flash in the display along with the
temperature. Adjustments to the settings should be
made within 30 seconds. The unit will exit the preset
programming mode if no adjustment is made within
this time.
4) To adjust the temperature, touch and hold the TEMP
UP arrow to increase or the DOWN arrow to decrease
the temperature until the desired preset temperature is
shown in the display.
5) To adjust the time setting, touch and hold the TIMER
UP arrow to increase or the DOWN arrow to decrease
the time until the desired preset time setting is shown
in the display.
6) Touch and hold the adjusted PRESET again for 5
seconds. Three chimes will signify that settings for the
PRESET have been changed. If 30 seconds elapse
before you touch and hold the PRESET, the unit will
exit the preset programming mode with no adjustments
made.
When Sabbath mode is initiated, the automatic shut-off
is disabled, requiring the unit to be turned off manually
by touching POWER ON/OFF.

Warming Drawer Operation 9
wolfappliance.com
Temperature Scale
The warming drawer can be changed from Fahrenheit (°F)
temperature to Celsius (°C) or vice versa.
CHANGING TE PERATURE SCALE
1) Warming drawer must be OFF.
2) Touch and hold both the TEMP UP and DOWN arrows
for 5 seconds.
3) After 5 seconds, a chime will sound, the backlighting
will turn on, and either ‘F’ or ‘C’ will appear, depending
on the current setting.
4) Touch the TEMP UP or DOWN arrow to select either
Fahrenheit (F) or Celsius (C).
5) With the desired temperature scale selected, touch
POWER ON/OFF to save the setting.
Control Panel Backlighting
The Wolf warming drawer has three options for control
panel backlighting; backlight off in Sabbath, backlight on
in Sabbath and backlight off in all modes. The backlight
defaults to ON in normal use and OFF in Sabbath mode.
CHANGING BACKLIGHTING
1) Warming drawer must be OFF.
2) Touch and hold TEMP UP arrow and TIMER UP arrow
for 5 seconds. The current backlight setting will appear
in the display.
3) Use the TIMER UP arrow to scroll through the three
backlight options; backlight off in Sabbath, backlight
on in Sabbath (50% power), and backlight off in all
modes. A selection should be made within 30 seconds.
The unit will default to the current backlight setting if a
new selection is not made within this time.
4) With the desired backlight setting selected, touch
POWER ON/OFF to save the setting.

Warming Drawer Operation 10
Warming Drawer Operation
Before using for the first time, remove all packaging
materials from inside the warming drawer. Clean the
warming drawer thoroughly to remove residual oil and
grease from the manufacturing process. Refer to care
recommendations on page 12.
TIPS FOR OPERATION
•Always start with hot food. The warming drawer will
keep hot food at serving temperature. Do not use the
warming drawer to heat cold food other than for
proofing yeast dough and crisping crackers, chips or
dry cereal.
•Always preheat the warming drawer. Preheat 3 minutes
for PROOF, 4 minutes for LOW, 7 minutes for MEDIUM
and 13 minutes for IG .
•Food in heat-safe glass and glass ceramic containers
may need higher temperature settings as compared to
food in metal containers.
•Repeated opening of the warming drawer will allow hot
air to escape and the food to cool.
•With large loads, it may be necessary to use a higher
temperature setting and to cover some of the cooked
food items.
•Food should be kept hot in the cooking container or
transferred to a heat-safe serving dish prior to being
placed into the warming drawer.
•Remove serving spoons, etc., before placing food
containers in warming drawer.
•Aluminum foil may be used to cover food to increase
moisture content.
•Do not place plastic containers or plastic wrap in the
warming drawer.
RACK FOR STACKING FOOD
The rack will fit in the warming drawer front to back and
allows you to double stack items. Always preheat the
warming drawer with the rack in position.
When holding hot, cooked foods and warming empty
serving dishes at the same time, place the serving dishes
on the bottom of the warming drawer and place food on
the rack.
WAR ING DRAWER PAN
The stainless steel warming drawer pan is removable for
cleaning. To remove, open the warming drawer
completely. Slide fingertips under the right and left side
edges of the pan. Firmly pull the pan upward, making sure
that all edges are clear from the interior of the unit.
To replace the warming drawer pan, open the warming
drawer completely. Place pan edges on the side rails of
the drawer frame. Open and close the drawer completely
to check operation.