woodmizer LT30HD Guide
E25 Motor
Safety, Operation, Maintenance
& Parts Manual
LT30 Super rev. F7.00 - J3.08
LT40 Super rev. F8.00 - J7.19
LT30HD Superrev. G1.00 - J8.09
LT40HD Superrev. G1.00 - K4.00
LT50HD rev. A1.01 - A6.00
Safety is our #1 concern! Read and understand
all safety information and instructions before oper-
ating, setting up or maintaining this machine.
January 2010
Form #772
©2019
Printed in the United States of America, all rights reserved. No part of this manual may be
reproduced in any form by any photographic, electronic, mechanical or other means or used in
any information storage and retrieval system without written permission from
Wood-Mizer
8180 West 10th Street
Indianapolis, Indiana 46214
&DOLIRUQLD
3URSRVLWLRQ:DUQLQJ
:$51,1*%UHDWKLQJJDVGLHVHOHQJLQHH[KDXVWH[SRVHV\RXWRFKHPLFDOVNQRZQWR
WKH6WDWHRI&DOLIRUQLDWRFDXVHFDQFHUDQGELUWKGHIHFWVRURWKHUUHSURGXFWLYHKDUP
$OZD\VVWDUWDQGRSHUDWHWKHHQJLQHLQDZHOOYHQWLODWHGDUHD
,ILQDQHQFORVHGDUHDYHQWWKHH[KDXVWWRWKHRXWVLGH
'RQRWPRGLI\RUWDPSHUZLWKWKHH[KDXVWV\VWHP
'RQRWLGOHWKHHQJLQHH[FHSWDVQHFHVVDU\
)RUPRUHLQIRUPDWLRQJRWRZZZ3ZDUQLQJVFDJRY
:$51,1*'ULOOLQJVDZLQJVDQGLQJRUPDFKLQLQJZRRGSURGXFWVFDQH[SRVH\RXWR
ZRRGGXVWDVXEVWDQFHNQRZQWRWKH6WDWHRI&DOLIRUQLDWRFDXVHFDQFHU$YRLGLQKDOLQJ
ZRRGGXVWRUXVHDGXVWPDVNRURWKHUVDIHJXDUGVIRUSHUVRQDOSURWHFWLRQ
)RUPRUHLQIRUPDWLRQJRWRZZZ3:DUQLQJVFDJRYZRRG
Table of Contents Section-Page
Table of Contents WMdoc072919 iii
TOC
SECTION 1 ABOUT THIS MANUAL 1-1
SECTION 2 OPERATION 2-1
2.1 Starting The Motor .................................................................................2-1
SECTION 3 MAINTENANCE 3-1
3.1 Safety......................................................................................................3-1
3.2 Battery ....................................................................................................3-2
3.3 Alternator Belt........................................................................................3-2
SECTION 4 REPLACEMENT PARTS 4-1
4.1 Motor Starter Assembly .........................................................................4-1
LT40 Super Rev. J7.05+ (2011+)
LT40HD Super Rev. K3.05+ (2011+)
LT50 Rev. A5.04+ (2011+)
4.2 Motor Starter Assembly .........................................................................4-3
LT30 Super Rev. F7.00 - J3.08
LT40 Super Rev. F8.00 - J7.05 (pre-2011)
LT30HD Super Rev. G1.00 - J8.09
LT40HD Super Rev. G1.00 - K3.05 (pre-2011)
LT50 Rev. A1.01 - A5.04 (pre-2011)
4.3 Motor Mount Assembly (220/380/415-440V) .......................................4-5
LT40 Super Rev. J7.08+
LT40HD Super Rev. K3.07+
LT50HD Rev. A5.07+
4.4 Motor Mount Assembly (220/380/415-440V) .......................................4-6
LT30 Super Rev. G2.00 - J3.08
LT40 Super Rev. G3.00 - J7.07
LT30HD Super Rev. G6.00 - J8.09
LT40HD Super Rev. G6.00 - K3.06
LT50HD Rev. A1.01 - A5.06
4.5 Motor Mount Assembly (575V).............................................................4-7
LT30 Super Rev. G6.00 - J3.08
LT40 Super Rev. G7.00 - J7.06
LT30HD Super Rev. H1.00 - J8.09
LT40HD Super Rev. H1.00 - K3.05
4.6 Motor Mount Assembly (220/380/415-440V) .......................................4-8
LT30 Super Rev. F7.00 - G1.02
LT40 Super Rev. F8.00 - G2.02
LT30HD Super Rev. G1.00 - G5.01
LT40HD Super Rev. G1.00 - G5.01
4.7 Motor Mount Assembly (575V).............................................................4-9
LT30 Super Rev. F7.00 - G5.00
LT40 Super Rev. F8.00 - G6.00
LT30HD Super Rev. G1.00 - G9.00
LT40HD Super Rev. G1.00 - G9.00
Table of Contents Section-Page
iv WMdoc072919 Table of Contents
4.8 Motor Assembly ...................................................................................4-10
LT40 Super Rev. J7.08+
LT40HD Super Rev. K3.07+
LT50HD Rev. A5.07+
4.9 Motor Assembly ...................................................................................4-11
LT30 Super Rev. G2.00 - J3.08
LT40 Super Rev. G3.00 - J7.07
LT30HD Super Rev. G6.00 - J8.09
LT40HD Super Rev. G6.00 - K3.06
LT50HD Rev. A1.01 - A5.06
4.10 Drive And Alternator Assembly (460V ) .............................................4-13
LT40 Super Rev. J7.08+
LT40HD Super Rev. K3.07+
LT50HD Rev. A5.07+
4.11 Drive And Alternator Assembly (460V & 575V) ................................4-15
LT30 Super Rev. J3.06 - J3.08
LT40 Super Rev. J4.07 - J7.07
LT30HD Super Rev. J8.07 - J8.09
LT40HD Super Rev. J8.08 - K3.06
LT50HD Rev. A1.01 - A5.06
4.12 Drive And Alternator Assembly (460V & 575V) ................................4-17
LT30 Super Rev. G6.00 - J3.05
LT40 Super Rev. G7.00 - J4.06
LT30HD Super Rev. H1.00 - J8.06
LT40HD Super Rev. H1.00 - J8.07
4.13 Drive and Alternator Assembly (460V U.S.) .......................................4-20
LT30 Super Rev. G2.00 - G5.00
LT40 Super Rev. G3.00 - G6.00
LT30HD Super Rev. G6.00 - G9.00
LT40HD Super Rev. G6.00 - G9.00
4.14 140A Alternator Retrofit (Premium Efficiency Motor) .......................4-22
4.15 140A Alternator Retrofit (Non-Premium Efficiency Motor) ...............4-24
4.16 Drive and Alternator Assembly (460V U.S.) .......................................4-26
LT30 Super Rev. F7.00 - G1.02
LT40 Super Rev. F8.00 - G2.02
LT30HD Super Rev. G1.00 - G5.01
LT40HD Super Rev. G1.00 - G5.01
4.17 Drive and Alternator Assembly (575V Canada) ..................................4-28
LT30 Super Rev. F7.00 - G5.00
LT40 Super Rev. F8.00 - G6.00
LT30HD Super Rev. G1.00 - G9.00
LT40HD Super Rev. G1.00 - G9.00
4.18 Engine Pulley Guards (E25).................................................................4-30
LT40 Super Rev. J7.08+
LT40HD Super Rev. K3.07+
LT50HD Rev. A5.07+
4.19 Motor Pulley Guards (E25) ..................................................................4-31
LT30 Super Rev. G6.00 - J3.09
LT40 Super Rev. G7.00 - J7.07
LT30HD Super Rev. H1.00 - J8.09
LT40HD Super Rev. H1.00 - K3.06
Table of Contents Section-Page
Table of Contents WMdoc072919 v
TOC
LT50HD Rev. A1.01 - A5.06
4.20 Motor Pulley Guards (E25) ..................................................................4-32
LT30 Super Rev. F7.00 - G5.00
LT40 Super Rev. F8.00 - G6.00
LT30HD Super Rev. G1.00 - G9.00
LT40HD Super Rev. G1.00 - G9.00
INDEX I
About This Manual
1
1-1 WMdoc072919 About This Manual
SECTION 1 ABOUT THIS MANUAL
This manual is provided as a supplement to the equipment manufacturer’s manuals. This
manual provides information specific to the use of this equipment on the Wood-Mizer®
sawmill. Refer to the sawmill operator’s manual and manufacturer's manual before
attempting to operate this equipment.
IMPORTANT! Read the sawmill operator’s manual and engine manu-
facturer’s manual for instructions and safety precautions before oper-
ating this equipment.
The information and instructions given in this manual do not amend or extend the limited
warranties for the equipment given at the time of purchase.
For electric sawmill installation instructions and power requirements, see Form 542.
E25 Motor
Wiring
Junction
Box
Serial Number/Motor Type
3H0722
Alternator
Operation
Starting The Motor
Operation WMdoc072919 2-1
2
SECTION 2 OPERATION
2.1 Starting The Motor
Motor Control Lights
See Figure 2-1. The following indicator lights are located on the sawmill control panel.
Alternator Charge Indicator: Lights up if the alternator is not charging the battery.
Key Switch Indicator: Lights up when the key is in either the on or accessory (#1 or #3)
position.
Motor Start
DANGER! Always be sure the blade is disengaged and all persons are
out of the path of the blade before starting the motor. Failure to do so
will result in serious injury.
WARNING! Be sure the power feed switch is in the neutral position
before turning the key switch to the on (#1) or accessory (#3) position.
This prevents accidental carriage movement. which may cause serious
injury or death.
FIG. 2-1
Operation
Starting The Motor
2
2-2 WMdoc072919 Operation
Turn the key switch to the start (#2) position and release.
Motor Shutoff
Turn the key switch to the off (#0) position.
Maintenance
Safety
Maintenance WMdoc072919 3-1
3
SECTION 3 MAINTENANCE
Refer to the manufacturer’s manual for maintenance intervals and procedures unless oth-
erwise instructed in this manual. Follow the manufacturer’s recommendations for dusty
conditions.
IMPORTANT! This manual only provides information about additional
procedures or procedures to be performed at different time intervals
than found in the manufacturer's manuals. Refer to the manufacturer's
manual for complete maintenance instructions.
WARNING! Clean sawdust from all guards, vents, control
boxes, or any area where sawdust may gather after every
shift. Failure to do so may result in fire, causing death or
serious injury.
3.1 Safety
Use caution when performing maintenance or service to the motor.
DANGER! Always be aware of and take proper protective measures
against rotating shafts, pulleys, fans, etc. Always stay a safe distance
from rotating members and make sure that loose clothing or long hair
does not engage rotating members resulting in possible injury.
DANGER! Make sure all electrical installation, service and/or mainte-
nance work is performed by a qualified electrician and is in accordance
with applicable electrical codes.
DANGER! Hazardous voltage inside the electric sawmill disconnect
box, starter box, and at the motor can cause shock, burns, or death.
Disconnect and lock out power supply before servicing! Keep all elec-
trical component covers closed and securely fastened during mill oper-
ation.
WARNING! Remove the blade before performing any engine service.
Failure to do so may result in serious injury.
WARNING! Always wear proper and necessary safety equipment
when performing service functions. Proper safety equipment includes
eye protection, breathing protection, hand protection and foot protec-
tion.
Maintenance
Battery
3
3-2 WMdoc072919 Maintenance
This symbol identifies the interval (hours of operation) at which each maintenance pro-
cedure should be performed. "AR" signifies maintenance procedures which should be
performed as required.
3.2 Battery
Check the battery electrolyte level every 50 hours of operation. See manufacturer’s man-
ual for instructions.
DANGER! Batteries expel explosive gases. Keep sparks, flames,
burning cigarettes, or other ignition sources away at all times. Always
wear safety goggles and a face shield when working near batteries.
Failure to do so will cause serious injury.
WARNING! Battery posts, terminals and related accessories contain
lead and lead compounds, chemicals known to the State of California
to cause cancer and reproductive harm. Wash hands after handling.
3.3 Alternator Belt
LT30 Super Rev. G6.00+
LT40 Super Rev. G7.00+
LT30HD Super Rev. H1.00+
LT40HD Super Rev. H1.00+
The belt tension should be checked after the first 100 hours of operation, when the bat-
tery is not charging properly or when the alternator belt is squealing.
If the battery continues to not charge properly or the belt continues to squeal after the ini-
tial belt adjustment, replace the belt.
IMPORTANT! Sawmills built prior to March 1999 were provided with a
sight hole in the alternator bracket to gauge belt tension. To achieve
proper belt tension, do not use the sight hole. Follow the procedure
below to check the belt tension and adjust if necessary.
1. Release the blade tension and remove the blade from the sawmill if necessary. Turn the
key switch to OFF (0) and remove the key.
2. Remove the drive belt cover and alternator cover.
0
50
100
Maintenance
Alternator Belt
Maintenance WMdoc072919 3-3
3
See Figure 3-1.
3. Use a belt tension gauge to measure the belt tension. Place the gauge on the belt at the
midpoint between the two pulleys. If the belt has more than 3/16” at 9 lb. of deflection,
tighten the belt as described below.
4. Loosen the upper pivot, lower pivot and the adjustment bolt jam nut.
5. Turn the belt tension adjustment bolt clockwise to tighten the belt, counterclockwise to
loosen the belt. Adjust the bolt until the proper belt tension is achieved.
CAUTION! Do not overtighten the alternator belt. Damage to the alter-
nator will occur.
6. After the alternator belt has been tensioned, tighten the adjustment bolt jam nut. Tighten
the upper and lower pivots and replace the belt covers.
LT30 Super Rev. F7.00 - G5.00
LT40 Super Rev. F8.00 - G6.00
LT30HD Super Rev. G1.00 - G9.00
LT40HD Super Rev. G1.00 - G9.00
1. Loosen the two clamp bolts located underneath the alternator mount assembly.
2. Turn the tensioner belt clockwise to tighten the alternator belt.
FIG. 3-1
Belt Adjustment
Bolt
Jam Nut Upper Pivot
Lower
Pivot
3H0748-11
Maintenance
Alternator Belt
3
3-4 WMdoc072919 Maintenance
See Figure 3-2.
FIG. 3-2
Loosen clamp
bolts (2)
Turn tensioner
bolt clockwise
to tighten alternator
belt
3H0715-3
Replacement Parts
Motor Starter Assembly
Replacement Parts E2597doc072919 4-1
4
E25
SECTION 4 REPLACEMENT PARTS
4.1 Motor Starter Assembly
LT40 Super Rev. J7.05+ (2011+)
LT40HD Super Rev. K3.05+ (2011+)
LT50 Rev. A5.04+ (2011+)
REF DESCRIPTION ( Indicates Parts Available In Assemblies Only) PART # QTY.
STARTER ASSEMBLY, 25HP 3-PHASE 50/60HZ 3450RPM ELECTRIC MOTOR 014399 1 1
1Bolt, 1/4-20 x 1 1/4” Hex Head Tap F05005-3 4
2Washer, 1/4” SAE Flat F05011-11 4
3Box, Electric Motor Starter Enclosure 014405 1
4Panel, Starter Box Component Mounting S10212 1
5Nut, 1/4-20 Hex Self-Locking F05010-9 11
6Interlock, D40-D80 Contactor Mechanical 023171-1 11
7Contactor, 65Amp 3P 12VDC Coil D-A Series 069521 13
8Screw, #10-24 x 1/2” Philips Pan Head Type 23 F05015-17 13
9DIN Rail, 35mm x 7.5mm x 10” Steel Sym 024474-10 1
10 Latch, Starter Box Door P20048 1
11 Screw, 1/4-20 X 1/2" Button Head Socket Stainless F05005-112 2
12 Socket, 8-pin Relay Sq-D #00605 Class 8501 Type NR52B E10216 1
Connect to
460 Volt 60 Hz
ONLY!
Wood-Mizer Products, Inc.
800-525-8100 Reorder #042015
Connecting this machine to
other types of power will
damage the electrical
system.
3H1105
1
23
4
5
5
6
7
8
9
10
11
5
12 13
14
15
16
17
18
18
19
23
24 22
20
21
Replacement Parts
Motor Starter Assembly
4
4-2 E2597doc072919 Replacement Parts
E25
13 Timer Kit, 12V Y-Delta Replacement 050826 1
14 Connector, SR507 Cord E20456 1
15 Ring, 1/2" Sealing E20460 1
16 Nut, 1/2" #141 Lock E20461 1
17 Plug, AS075 OilTite Painted 024250 1
18 Connector, 1.25" 45° Nylon 014448 2
19 Conduit, 1.25" Maxi-Flex R01633 3.58 Ft.
20 Screw, #6 x 1” Phillips Pan Head Type A Sheet Metal F05004-42 2
21 Clamp, Plastic DIN Rail E22707 12
22 Decal, 460V 60Hz Power Supply Caution 042015 1
23 DECAL, Y-DELTA E20/E25 ELECTRIC WIRING 014344 1
24 DECAL, ELECTRICAL HAZARD DANGER S20061 1
1 Starter Assembly 014399 modified 1/11 to accept DIN-rail mounted Contactors 069521 due to a change in vendor supply. Replace-
ment of old-style contactors requires DIN rail 024474-10, three screws F05015-17, two clamps E22707 and new interlock 023171-1.
Three 5/32” diameter holes in the mounting panel are required to mount DIN rail. New contactors include transient suppression,
eliminating the need for three diode suppression modules 023360.
Replacement Parts
Motor Starter Assembly
Replacement Parts E2597doc072919 4-3
4
E25
4.2 Motor Starter Assembly
LT30 Super Rev. F7.00 - J3.08
LT40 Super Rev. F8.00 - J7.05 (pre-2011)
LT30HD Super Rev. G1.00 - J8.09
LT40HD Super Rev. G1.00 - K3.05 (pre-2011)
LT50 Rev. A1.01 - A5.04 (pre-2011)
REF DESCRIPTION ( Indicates Parts Available In Assemblies Only) PART # QTY.
STARTER ASSEMBLY, 25HP 3-PHASE 50/60HZ 3450RPM ELECTRIC MOTOR 014399 1 1
1Bolt, 1/4-20 x 1 1/4” Hex Head Tap F05005-3 4
2Washer, 1/4” SAE Flat F05011-11 4
3Box, Electric Motor Starter Enclosure 014405 1
4Panel, Starter Box Component Mounting S10212 1
5Nut, 1/4-20 Hex Self-Locking F05010-9 10
6Interlock, Mechanical for LP1D65 023171 11
7Contactor, 65Amp 480Volt 3Phase 12VDC Coil 023169 13
8Bolt, #8-32 x 1/2” Slotted Hex Head F05015-18 9
3H0408B
1
2
3
4
5
5
6
7
8
9
10
11
5
12
13
14
15
16
17
18
18
19
20
21
Replacement Parts
Motor Starter Assembly
4
4-4 E2597doc072919 Replacement Parts
E25
9Diode, Suppression Module D40-D80 023360 13
10 Latch, Starter Box Door P20048 1
11 Screw, 1/4-20 X 1/2" Button Head Socket F05005-62 2
12 Socket, 8-pin Relay Sq-D #00605 Class 8501 Type NR52B E10216 1
13 Timer Kit, 12V Y-Delta Replacement 050826 2 1
14 Connector, SR507 Cord E20456 1
15 Ring, 1/2" Sealing E20460 1
16 Nut, 1/2" #141 Lock E20461 1
17 Plug, AS075 OilTite Painted 024250 3 1
18 Connector, 1.25" 45° Nylon 014448 2
19 Conduit, 1.25" Maxi-Flex R01633 3.58 Ft.
20 DECAL, Y-DELTA E20/E25 ELECTRIC WIRING 014344 1
21 DECAL, ELECTRICAL HAZARD DANGER S20061 1
1 Starter Assembly 014399 modified 1/11 to accept DIN-rail mounted Contactors 069521 due to a change in vendor supply (See Sec-
tion 4.1). Original Contactors 023169 available for service while supplies last. Replacement of old-style contactors with new requires
DIN rail 024474-10, three screws F05015-17, two clamps E22707 and new interlock 023171-1. Three 5/32” diameter holes in the
mounting panel are required to mount DIN rail. New contactors include transient suppression, eliminating the need for three diode
suppression modules 023360.
2 Replacement Kit 050826 replaces Timer 023170 supplied prior to LT30 Super Rev. H9.02, LT40 Super Rev. J1.02, and
LT30HD/40HD Super Rev. J5.02. Kit includes new polarized timer and instructions on how to change wiring to accept the new timer.
3 Replaces E20570 unpainted plug.
Replacement Parts
Motor Mount Assembly (220/380/415-440V)
Replacement Parts E2597doc072919 4-5
4
E25
4.3 Motor Mount Assembly (220/380/415-440V)
LT40 Super Rev. J7.08+
LT40HD Super Rev. K3.07+
LT50HD Rev. A5.07+
REF DESCRIPTION (Indicates Parts Available In Assemblies Only) PART # QTY.
1 MOUNT WELDMENT, ELECTRIC MOTOR (2011) 065428 1
2 BOLT, 1/2-13 1 1/2” HEX HEAD GRADE 5 F05008-33 1
3 NUT, 1/2-13 HEX JAM F05010-31 2
4 PIN WELDMENT, ENGINE MOUNT PIVOT 014154 1
5 BOLT, 1/2-13 X 1 1/4” HEX HEAD GRADE 5 F05008-37 1
6 NUT, 1/2-13 NYLON LOCK F05010-8 1
7 BOLT, 3/8-16 X 1” HEX HEAD F05007-7 3
8 CLAMP WELDMENT, MOTOR MOUNT BUSHING 014540 3
BUSHING ASSEMBLY, MOTOR MOUNT 016380 3
9Bushing, 2” OD x 2” 016378 1
10 Bearing, 1” x 1 1/4” x 2” 016379 1
11 NUT, 3/8-16 HEX NYLON LOCK F05010-10 6
1
3
2
4
5
6
7
8
9
10
11
3H1106
3
Replacement Parts
Motor Mount Assembly (220/380/415-440V)
4
4-6 E2597doc072919 Replacement Parts
E25
4.4 Motor Mount Assembly (220/380/415-440V)
LT30 Super Rev. G2.00 - J3.08
LT40 Super Rev. G3.00 - J7.07
LT30HD Super Rev. G6.00 - J8.09
LT40HD Super Rev. G6.00 - K3.06
LT50HD Rev. A1.01 - A5.06
REF DESCRIPTION (Indicates Parts Available In Assemblies Only) PART # QTY.
MOUNT KIT, ELECTRIC MOTOR 016318 1
1 Mount Kit 016318 includes new rubber clutch handle mount bushings and hardware standard on LT30 Super Rev. G9.00, LT40 Super
Rev. H1.00 and LT30HD/40HD Super Rev. H4.00 (See Clutch Handle parts in Sawmill Parts Manual).
1
1Mount Weldment, Electric Motor 023599 1
2 BOLT, 3/8-16 X 3” HEX HEAD FULL THREAD F05007-1 2
3 NUT, 3/8-16 HEX JAM F05010-29 2
4 PIN WELDMENT, ENGINE MOUNT PIVOT 014154 1
5 BOLT, 1/2-13 X 1 1/4” HEX HEAD GRADE 5 F05008-37 1
6 NUT, 1/2-13 NYLON LOCK F05010-8 1
7 BOLT, 3/8-16 X 1” HEX HEAD F05007-7 3
8 CLAMP WELDMENT, MOTOR MOUNT BUSHING 014540 3
BUSHING ASSEMBLY, MOTOR MOUNT 016380 2
2 New assembly 016380 replaces original rubber pivot bushing P12164 and bronze bushing P05041 supplied prior to LT30 Super Rev.
H1.00, LT40 Super Rev. H2.00 and LT30HD/40HD Super Rev. H5.00. NOTE: When replacing original components with new assem-
bly, it is best to replace all three assemblies at the same time.
3
9Bushing, 2” OD x 2” 016378 1
10 Bearing, 1” x 1 1/4” x 2” 016379 1
11 NUT, 3/8-16 HEX NYLON LOCK F05010-10 6
1
2
2
3
3
4
5
6
7
8
9
10
11
3H0737
Replacement Parts
Motor Mount Assembly (575V)
Replacement Parts E2597doc072919 4-7
4
E25
4.5 Motor Mount Assembly (575V)
LT30 Super Rev. G6.00 - J3.08
LT40 Super Rev. G7.00 - J7.06
LT30HD Super Rev. H1.00 - J8.09
LT40HD Super Rev. H1.00 - K3.05
REF DESCRIPTION (Indicates Parts Available In Assemblies Only) PART # QTY.
MOUNT KIT, ELECTRIC MOTOR 016318 1
1 Mount Kit 016318 includes new rubber clutch handle mount bushings and hardware standard after 6/99 (See Clutch Handle parts in
Sawmill Parts Manual). 575V no longer available on LT40 Rev. J7.07, LT40HD Rev. K3.06 & LT50HD Rev. A5.06 and later.
1
1Mount Weldment, Electric Motor 023599 1
2 BOLT, 3/8-16 X 3” HEX HEAD FULL THREAD F05007-1 2
3 NUT, 3/8-16 HEX JAM F05010-29 2
4 PIN WELDMENT, ENGINE MOUNT PIVOT 014154 1
5 BOLT, 1/2-13 X 1 1/4” HEX HEAD GRADE 5 F05008-37 1
6 NUT, 1/2-13 NYLON LOCK F05010-8 1
7 BOLT, 3/8-16 X 1” HEX HEAD F05007-7 3
8 CLAMP WELDMENT, MOTOR MOUNT BUSHING 014540 3
BUSHING ASSEMBLY, MOTOR MOUNT 016380 2
2 New assembly 016380 replaces original rubber pivot bushing P12164 and bronze bushing P05041 originally supplied. NOTE: When
replacing original components with new assembly, it is best to replace all three assemblies at the same time.
3
9Bushing, 2” OD x 2” 016378 1
10 Bearing, 1” x 1 1/4” x 2” 016379 1
11 NUT, 3/8-16 HEX NYLON LOCK F05010-10 6
1
2
2
3
3
4
5
6
7
8
9
10
11
3H0737
Replacement Parts
Motor Mount Assembly (220/380/415-440V)
4
4-8 E2597doc072919 Replacement Parts
E25
4.6 Motor Mount Assembly (220/380/415-440V)
LT30 Super Rev. F7.00 - G1.02
LT40 Super Rev. F8.00 - G2.02
LT30HD Super Rev. G1.00 - G5.01
LT40HD Super Rev. G1.00 - G5.01
REF DESCRIPTION (Indicates Parts Available In Assemblies Only) PART # QTY.
MOUNT KIT, ELECTRIC MOTOR 016322 1
1 Mount Kit 016322 includes new rubber clutch handle mount bushings and hardware standard after 6/99 (See Clutch Handle parts
in Sawmill Parts Manual).
1
1Mount Weldment, Electric Motor 014059 1
2 BOLT, 3/8-16 X 3” HEX HEAD FULL THREAD F05007-1 2
3 NUT, 3/8-16 HEX JAM F05010-29 2
4 PIN WELDMENT, ENGINE MOUNT PIVOT 014154 1
5 BOLT, 1/2-13 X 1 1/4” HEX HEAD GRADE 5 F05008-37 1
6 NUT, 1/2-13 NYLON LOCK F05010-8 1
7 BOLT, 3/8-16 X 1” HEX HEAD F05007-7 3
8 CLAMP WELDMENT, MOTOR MOUNT BUSHING 014540 3
BUSHING ASSEMBLY, MOTOR MOUNT 016380 2
2 New assembly 016380 replaces original rubber pivot bushing P12164 and bronze bushing P05041 originally supplied. NOTE: When
replacing original components with new assembly, it is best to replace all three assemblies at the same time.
3
9Bushing, 2” OD x 2” 016378 1
10 Bearing, 1” x 1 1/4” x 2” 016379 1
11 NUT, 3/8-16 HEX NYLON LOCK F05010-10 6
1
2
3
2
3
4
5
6
7
7
11
8
8
9
9
10
9
10
11
3H0229-1
Other manuals for LT30HD
4
This manual suits for next models
2
Table of contents
Other woodmizer Industrial Equipment manuals
woodmizer
woodmizer BMT200 Guide
woodmizer
woodmizer PD200 Series Guide
woodmizer
woodmizer LT30 Manual instruction
woodmizer
woodmizer LS LT60 Guide
woodmizer
woodmizer MP180 User manual
woodmizer
woodmizer E10 Guide
woodmizer
woodmizer LT15SA Manual instruction
woodmizer
woodmizer LT15 Series Manual instruction
woodmizer
woodmizer MF130 E3S User manual
woodmizer
woodmizer SlabMizer MB200 User manual
woodmizer
woodmizer TRB-S Guide
woodmizer
woodmizer Shop Series User manual
woodmizer
woodmizer LT28 Guide
woodmizer
woodmizer Accuset 2 Guide
woodmizer
woodmizer LT35 User manual
woodmizer
woodmizer HR250 User manual
woodmizer
woodmizer LT30 Manual instruction
woodmizer
woodmizer LT70 Series Guide
woodmizer
woodmizer LMS-HPR Setup guide
woodmizer
woodmizer LT15SC Series Manual instruction
