Woodstock SHOP FOX W1668 User manual

***Keep for Future Reference***
W1848
W1668
MODEL W1668/W1848
131⁄4" OSCILLATING
DRILL PRESS
#18837MN Printed in ChinaV3.10.22
OWNER'S MANUAL
(FOR MODELS MANUFACTURED SINCE 06/22)
Phone: [phone] • Online Technical Support: [email protected]
COPYRIGHT © MARCH, 2017 BY WOODSTOCK INTERNATIONAL, INC., REVISED OCTOBER, 2022 (CS)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.

This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and compre-
hension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property
damage from negligence, improper training, machine modifications or
misuse.
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement and other masonry products.
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equip-
ment, such as those dust masks that are specially designed to filter
out microscopic particles.

SETUPELECTRICAL MAINTENANCE SERVICE PARTS
OPERATIONS
SAFETYINTRODUCTION
USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!
INTRODUCTION .....................................2
Woodstock Technical Support .................. 2
W1668 Machine Specifications ................. 3
W1848 Machine Specifications ................. 5
Controls & Components ......................... 8
SAFETY ............................................. 10
Standard Machinery Safety Instructions .... 10
Additional Safety for Drill Presses........... 12
ELECTRICAL ....................................... 13
Circuit Requirements .......................... 13
Grounding Requirements...................... 14
Extension Cords ................................ 14
SETUP .............................................. 15
Unpacking ....................................... 15
Items Needed for Setup....................... 15
Hardware Recognition Chart ................. 16
Inventory ........................................ 17
Cleaning Machine............................... 18
Machine Placement ............................ 19
Bench Mounting (W1668)...................... 20
Anchoring to Floor (W1848) .................. 20
Assembly......................................... 21
Dust Collection ................................. 27
Test Run.......................................... 28
Spindle Break-In ................................ 29
OPERATIONS....................................... 30
General .......................................... 30
Adjusting Table Height & Tilt ................ 31
Changing Spindle Speed....................... 32
Drill Press Speed Chart ........................ 33
Adjusting Depth Stop .......................... 33
Calculating Spindle Speed for Drilling ...... 35
Changing Drill Bit/Drum....................... 36
Using the Oscillator............................ 37
ACCESSORIES ...................................... 39
Drill Press Accessories ......................... 39
MAINTENANCE .................................... 40
General .......................................... 40
Cleaning & Protecting ......................... 40
Sanding Sleeves................................. 40
Inspecting/Replacing Belts ................... 41
Lubrication ...................................... 41
SERVICE ............................................ 43
General .......................................... 43
Tensioning Feed Shaft Return Spring........ 43
Adjusting Quill Shaft Screw .................. 45
Troubleshooting................................. 46
Electrical Safety Instructions................. 48
Wiring Diagram ................................. 49
PARTS .............................................. 50
W1668 Main ..................................... 50
W1848 Main ..................................... 53
Labels & Cosmetics ............................ 56
WARRANTY ........................................ 57
Contents

-2-
Model W1668/W1848 (Mfd. Since 06/22)
INTRODUCTION
INTRODUCTION
Woodstock Technical Support
This machine has been specially designed to provide many years of trouble-free service. Close attention
to detail, ruggedly built parts and a rigid quality control program assure safe and reliable operation.
Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to
include the basic information for safety, setup, operation, maintenance, and service of this product.
We stand behind our machines! In the event that questions arise about your machine, please
contact Woodstock International Technical Support at [phone] Ext. 2 or send e-mail to:
[e-mail]. Our knowledgeable staff will help you troubleshoot problems and pro-
cess warranty claims.
If you need the latest edition, you can download it from http://www.woodstockint.com/manuals.
If you have comments about this manual, please contact us at:
Woodstock International, Inc.
Attn: Technical Documentation Manager
P.O. Box 2309
Bellingham, WA 98227
Email: [e-mail]
No list of safety guidelines can be complete.
Every shop environment is different. Always
consider safety first, as it applies to your
individual working conditions. Use this and
other machinery with caution and respect.
Failure to do so could result in serious per-
sonal injury, damage to equipment, or poor
work results.
Like all machinery, there is a potential dan-
ger when operating this machine. Accidents
are frequently caused by lack of familiarity
or failure to pay attention. Use this machine
with respect and caution to decrease the
risk of operator injury. If normal safety pre-
cautions are overlooked or ignored, serious
personal injury may occur.

-3-
Model W1668/W1848 (Mfd. Since 06/22)
INTRODUCTION
Model W1668 Machine Specifications, Page 1 of 3
MODEL W1668
131/4" OSCILLATING BENCHTOP DRILL PRESS
Product Dimensions
Weight.......................................................................................................... 113 lbs.
Width (side‐to‐side) x Depth (front‐to‐back) x Height........................................ 15 x 24 x 38 in.
Footprint (Length x Width)......................................................................... 17‐1/2 x 11 in.
Shipping Dimensions
Carton #1
Type............................................................................................. Cardboard Box
Content................................................................................................. Machine
Weight.................................................................................................... 61 lbs.
Length x Width x Height..................................................................... 25 x 16 x 11 in.
Must Ship Upright............................................................................................ No
Carton #2
Type............................................................................................. Cardboard Box
Content..................................................................................................... Base
Weight.................................................................................................... 62 lbs.
Length x Width x Height...................................................................... 32 x 19 x 9 in.
Must Ship Upright............................................................................................ No
Electrical
Power Requirement.................................................................... 110V, Single‐Phase, 60 Hz
Full‐Load Current Rating........................................................................................... 9A
Minimum Circuit Size............................................................................................. 15A
Connection Type......................................................................................... Cord & Plug
Power Cord Included.............................................................................................. Yes
Power Cord Length............................................................................................ 108 in.
Power Cord Gauge............................................................................................ 18 AWG
Plug Included....................................................................................................... Yes
Included Plug Type............................................................................................... 5‐15
Switch Type............................................................ Paddle Safety Switch w/Removable Key
Motors
Main
Horsepower.............................................................................................. 3/4 HP
Phase.............................................................................................. Single‐Phase
Amps........................................................................................................... 9A
Speed.................................................................................................. 1725 RPM
Type......................................................................... TEFC Capacitor‐Start Induction
Power Transfer ............................................................................................ Belt
Bearings............................................................... Shielded & Permanently Lubricated
Centrifugal Switch/Contacts Type................................................................. External

-4-
Model W1668/W1848 (Mfd. Since 06/22)
INTRODUCTION
Model W1668 Machine Specifications, Page 2 of 3
Main Specifications
Operation Information
Type.................................................................................................. Oscillating
Swing................................................................................................. 13‐1/4 in.
Spindle Taper.............................................................................................. JT33
Spindle Travel........................................................................................ 3‐1/8 in.
Max. Distance From Spindle to Column........................................................... 6‐3/4 in.
Max. Distance From Spindle to Table............................................................ 17‐1/4 in.
Number of Spindle Speeds.................................................................................. 12
Range of Spindle Speeds..................................................................... 250 – 3050 RPM
Max. Head Swivel..................................................................................... 360 deg.
Drilling Capacity (Mild Steel)............................................................... 5/8 in. in Steel
Drill Chuck Type.............................................................................. JT33 Key Chuck
Drill Chuck Size..................................................................................... 1 – 16 mm
Oscillating Stroke Length.............................................................................. 3/4 in.
Spindle Information
Distance From Spindle to Base......................................................................... 24 in.
Quill Diameter........................................................................................ 1.565 in.
Table Information
Max. Table Tilt (Left/Right).......................................................................... 90 deg.
Table Swing............................................................................................ 360 deg.
Table Swivel Around Center........................................................................ 360 deg.
Table Swivel Around Column....................................................................... 360 deg.
Max. Movement of Work Table................................................................... 11‐3/4 in.
Table Diameter...................................................................................... 12‐3/8 in.
Table Thickness............................................................................................ 1 in.
Vertical Table Travel.............................................................. Crank Handle Operation
Number of T‐Slots............................................................................................. 5
T‐Slot Size............................................................................................... 5/8 in.
T‐Slot Centers.............................................................................................. 3 in.
Floor‐To‐Table Height.................................................................... 9‐1/2 – 21‐1/4 in.
Construction
Table............................................................................. Precision‐Ground Cast Iron
Column..................................................................................................... Steel
Spindle Housing....................................................................................... Cast Iron
Head.................................................................................................... Cast Iron
Base.................................................................................................... Cast Iron
Paint Type/Finish...................................................................................... Enamel
Other Related Information
Base Length.......................................................................................... 17‐1/2 in.
Base Width................................................................................................ 11 in.
Column Diameter...................................................................................... 2.79 in.
Depth Stop Type......................................................... Threaded Rod with Positive Stop
Number of Dust Ports......................................................................................... 1
Dust Port Size.............................................................................................. 2 in.

-5-
Model W1668/W1848 (Mfd. Since 06/22)
INTRODUCTION
Model W1848 Machine Specifications, Page 1 of 2
MODEL W1848
131/4" OSCILLATING FLOOR DRILL PRESS
Product Dimensions
Weight.......................................................................................................... 122 lbs.
Width (side‐to‐side) x Depth (front‐to‐back) x Height........................................ 15 x 24 x 63 in.
Footprint (Length x Width)......................................................................... 17‐1/2 x 11 in.
Shipping Dimensions
Type.................................................................................................... Cardboard Box
Content........................................................................................................ Machine
Weight.......................................................................................................... 138 lbs.
Length x Width x Height........................................................................... 58 x 22 x 11 in.
Must Ship Upright.................................................................................................. Yes
Electrical
Power Requirement.................................................................... 110V, Single‐Phase, 60 Hz
Full‐Load Current Rating........................................................................................... 9A
Minimum Circuit Size............................................................................................. 15A
Connection Type......................................................................................... Cord & Plug
Power Cord Included.............................................................................................. Yes
Power Cord Length............................................................................................. 72 in.
Power Cord Gauge............................................................................................ 18 AWG
Plug Included....................................................................................................... Yes
Included Plug Type............................................................................................... 5‐15
Switch Type............................................................ Paddle Safety Switch w/Removable Key
Motors
Main
Horsepower.............................................................................................. 3/4 HP
Phase.............................................................................................. Single‐Phase
Amps........................................................................................................... 9A
Speed.................................................................................................. 1725 RPM
Type......................................................................... TEFC Capacitor‐Start Induction
Power Transfer ............................................................................................ Belt
Bearings............................................................... Shielded & Permanently Lubricated
Centrifugal Switch/Contacts Type.................................................................. Internal

-6-
Model W1668/W1848 (Mfd. Since 06/22)
INTRODUCTION
Model W1848 Machine Specifications, Page 2 of 2
Main Specifications
Operation Information
Type.................................................................................................. Oscillating
Swing................................................................................................. 13‐1/4 in.
Spindle Taper.............................................................................................. JT33
Spindle Travel........................................................................................ 3‐1/8 in.
Max. Distance From Spindle to Column........................................................... 6‐5/8 in.
Number of Spindle Speeds.................................................................................. 12
Range of Spindle Speeds..................................................................... 250 ‐ 3050 RPM
Max. Head Swivel..................................................................................... 360 deg.
Drilling Capacity (Mild Steel)......................................................................... 5/8 in.
Drill Chuck Type.............................................................................. JT33 Key Chuck
Drill Chuck Size................................................................................. 3/64 ‐ 5/8 in.
Oscillating Stroke Length.............................................................................. 3/4 in.
Spindle Information
Quill Diameter........................................................................................ 1.565 in.
Table Information
Max. Table Tilt (Left/Right).......................................................................... 90 deg.
Table Swivel Around Center........................................................................ 360 deg.
Table Swivel Around Column....................................................................... 360 deg.
Max. Movement of Work Table................................................................... 25‐1/4 in.
Table Diameter...................................................................................... 12‐3/8 in.
Table Thickness............................................................................................ 1 in.
Vertical Table Travel.............................................................. Crank Handle Operation
Number of T‐Slots............................................................................................. 5
T‐Slot Size............................................................................................... 1/2 in.
T‐Slot Centers.............................................................................................. 3 in.
Construction
Table............................................................................. Precision‐Ground Cast Iron
Column..................................................................................................... Steel
Spindle Housing....................................................................................... Cast Iron
Head.................................................................................................... Cast Iron
Base.................................................................................................... Cast Iron
Paint Type/Finish...................................................................................... Enamel
Other Related Information
Depth Stop Type............................................................ Threaded Rod w/Positive Stop
Number of Dust Ports......................................................................................... 1
Dust Port Size.............................................................................................. 2 in.
Other
Country of Origin ............................................................................................... China
Warranty ....................................................................................................... 2 Years
Approximate Assembly & Setup Time ................................................................. 30 Minutes
Serial Number Location .................................................................................... ID Label
ISO 9001 Factory .................................................................................................. Yes

-7-
Model W1668/W1848 (Mfd. Since 06/22)
INTRODUCTION
Identification
Become familiar with the names and locations of the controls and features shown below to better
understand the instructions in this manual.
Base
Motor
Chuck
Guard
Table
Drill
Chuck
Column
Table Insert
Storage
Dust Port
Spindle
Handle
(1 of 3)
Motor
Lock
Screw
Depth Stop
Table
Lock Lever Table
Rotation
Lock Lever
Spindle Return
Spring
Table
Height
Crank
Pulley
Cover
ON/OFF Switch
w/Disabling Key
For Your Own Safety, Read Instruction Manual Before Operating Drill Press
a) Wear eye protection.
b) Do not wear gloves, necktie, or loose clothing.
c) Clamp workpiece or brace against column to prevent rotation.
d) Use recommended speed for drill accessory and workpiece material.

-8-
Model W1668/W1848 (Mfd. Since 06/22)
INTRODUCTION
Controls & Components
Refer to the Figures 1–5and the following descriptions to
become familiar with the basic controls and components
of this machine. Understanding these items and how they
work will help you understand the rest of the manual and
stay safe when operating this machine.
To reduce your risk of serious injury
or damage to the machine, read this
entire manual BEFORE using machine.
A. ON/OFF Switch w/Disabling Key: Turns motor ON
when moved up; turns motor OFF when moved
down. Removal of yellow key disables switch so
motor cannot start.
B. Depth Stop: Stops spindle travel at predetermined
depth.
C. Spindle Return Spring: Automatically returns quill
into headstock.
Figure 1. Left side of headstock.
A
B
C
Figure 2. Right side of headstock.
D
E
D. Motor Lock Screw: Adjusts motor position to tension
and release belt.
E. Spindle Handle (1 of 3): Moves spindle down when
pulled down. Spindle automatically returns to top
position when released.