Woodstock SHOP FOX W1755 User manual

OWNER'S MANUAL
MODEL W1755
6" PARALLELOGRAM JOINTER
Phone: [phone] • On-Line Technical Support: [email protected]
COPYRIGHT © MARCH, 2007 BY WOODSTOCK INTERNATIONAL, INC. REVISED APRIL, 2007.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC. Printed in China
#9160TR



















 
 
 






SET UPELECTRICAL MAINTENANCE SERVICE PARTS
OPERATIONSSAFETYINTRODUCTION
USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!
Table of Contents
INTRODUCTION ...................................... 2
Woodstock Technical Support .................. 2
Controls and Features ........................... 4
SAFETY ................................................ 5
Standard Safety Instructions ................... 5
Additional Safety Instructions for Jointers ... 7
Avoiding Potential Injuries ..................... 8
ELECTRICAL .......................................... 9
110V/220V Operation ............................ 9
Extension Cords .................................. 9
Electrical Specifications ........................ 9
SETUP ................................................10
Unpacking ........................................10
Items Needed for Setup ........................10
Inventory .........................................11
Machine Placement .............................12
Cleaning Machine ................................12
Assembly ..........................................13
Dust Collection ..................................17
Knife Setting Jig .................................17
Test Run ..........................................18
OPERATIONS ........................................19
General ...........................................19
Basic Controls ....................................20
Stock Inspection & Requirements ............21
Squaring Stock ...................................22
Surface Planing ..................................23
Edge Jointing ....................................24
Bevel Cutting ....................................25
Rabbet Cutting ..................................26
MAINTENANCE ......................................27
General ...........................................27
Cleaning ..........................................27
V-Belts ............................................27
Lubrication .......................................27
Maintenance Schedule ..........................27
SERVICE ..............................................28
General ...........................................28
Inspecting Knives ................................28
Adjusting/Replacing Knives ....................29
Checking/Adjusting Table Parallelism .......32
Setting Outfeed Table Height .................35
Setting Infeed Table Height ...................36
Calibrating Depth Scale ........................36
Setting Fence Stops .............................37
V-Belt Replacement ............................38
Pulley Alignment ................................39
Electrical Components .........................40
110V Wiring Diagram ...........................41
220V Wiring Diagram ...........................41
Troubleshooting .................................42
PARTS ................................................44
Stand Breakdown ................................44
Stand Parts List ..................................45
Jointer Breakdown ..............................46
Jointer Parts List ................................47
Labels/Cosmetic Parts .........................49
Warranty ..........................................50

-2-
W1755 6" Parallelogram Jointer
INTRODUCTION
Woodstock Technical Support
Your new SHOP FOX® 6" Parallelogram Jointer has been specially designed to provide many years of
trouble-free service. Close attention to detail, ruggedly built parts and a rigid quality control program
assure safe and reliable operation.
Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to
include the basic information for safety, setup, operation, maintenance, and service of this product.
We stand behind our machines! In the event that questions arise about your machine, please contact
Woodstock International Technical Support at [phone] or send e-mail to: tech-support@shopfox.
biz. Our knowledgeable staff will help you troubleshoot problems and process warranty claims.
INTRODUCTION
If you need the latest edition of this manual, you can download it from http://www.shopfox.biz.
If you have comments about this manual, please contact us at:
Woodstock International, Inc.
Attn: Technical Documentation Manager
P.O. Box 2309
Bellingham, WA 98227
Email: [e-mail]

-3-
W1755 6" Parallelogram Jointer
INTRODUCTION
Phone #: [phone] • Online Tech Support: [e-mail] • Web: www.shopfox.biz
MACHINE
SPECIFICATIONS
Motor
Type .........................................................................................TEFC Capacitor Start Induction
Horsepower .............................................................................................................. 11⁄2 HP
Phase / Voltage .................................................................................. Single-Phase / 110V/220V
Amps ................................................................................................................... 15A/7.5A
Cycle / RPM ............................................................................................. 60 Hertz / 3450 RPM
Switch ............................................................................... Push Button w/Oversized OFF Button
Power Transfer .......................................................................................................Belt Drive
Bearings ..................................................................................... Sealed and Lubricated for Life
Capacity
Maximum Depth of Cut (per pass) ........................................................................................1⁄8"
Maximum Width of Cut ...................................................................................................... 6"
Cutterhead Speed ................................................................................................... 4850 RPM
Cuts Per Minute ..........................................................................................................19,400
Overall Dimensions
Table Size .......................................................................................................6" W X 551⁄2" L
Height (from floor to table) ............................................................................................ 321⁄2"
Overall Length ............................................................................................................ 551⁄2"
Overall Width .............................................................................................................. 241⁄2"
Shipping Weight ........................................................................................................ 347 lbs.
Net Weight .............................................................................................................. 320 lbs.
Box #1 Size ...................................................................................................... 63" x 22" x 14"
Box #2 Size ...................................................................................................... 29" x 20" x 28"
Stand Footprint .................................................................................................... 27" x 201⁄2"
Cutterhead ............................................................................................................... 4-Knife
Cutterhead Diameter ......................................................................................................... 3"
Cutterhead Knife Size .......................................................................................... 6" x 3⁄4" x 1⁄8"
Construction
Tables ............................................................................................ Precision Ground Cast Iron
Fence Assembly ....................................................................................................... Cast Iron
Body Assembly ........................................................................................................Cast Iron
Stand .........................................................................................................................Steel
Guard ..................................................................................................................Aluminum
Bearings ..................................................................................... Sealed and Lubricated for Life
Features
Parallelogram-Style Tables
Top Mount Switch Controls
Built-In Mobile Base
5" Tall Fence
Included Push Blocks
Included Knife Setting Jig
MODEL W1755
6" PARALLELOGRAM JOINTER

-4-
W1755 6" Parallelogram Jointer
INTRODUCTION
Controls and Features
A. Outfeed Table
B. Fence
C. Cutterhead Guard
D. ON/OFF Switch
E. Infeed Table
F. Infeed Table Adjustment Lever
G. Cutting Depth Scale
H. Infeed Table Lock
I. Mobile Base Lock Pedal
J. Outfeed Table Lock
K. Outfeed Table Adjustment Lever
L. Dust Port
M. Fence Tilt Handle
N. Fence Tilt Lock
O. Outfeed Table Positive Stops
P. Infeed Table Positive Stops
Q. Belt Guard
R. Fence Lock
S. Fence Tilt Release Plunger
L
A
B
C
D
E
F
G
I
J
K
H
P
MN
R
Q
O
S

-5-
W1755 6" Parallelogram Jointer
SAFETY
SAFETY
READ MANUAL BEFORE OPERATING MACHINE.
FAILURE TO FOLLOW INSTRUCTIONS BELOW WILL
RESULT IN PERSONAL INJURY.
Standard Safety Instructions
1. READ THROUGH THE ENTIRE MANUAL BEFORE STARTING MACHINERY. Machinery presents serious
injury hazards to untrained users.
2. ALWAYS USE ANSI APPROVED SAFETY GLASSES WHEN OPERATING MACHINERY. Everyday eye-
glasses only have impact resistant lenses—they are NOT safety glasses.
3. ALWAYS WEAR A NIOSH APPROVED RESPIRATOR WHEN OPERATING MACHINERY THAT PRODUCES
DUST. Wood dust is a carcinogen and can cause cancer and severe respiratory illnesses.
4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause
permanent hearing damage.
5. WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, or jewelry which may
get caught in moving parts. Wear protective hair covering to contain long hair and wear non-slip
footwear.
6. NEVER OPERATE MACHINERY WHEN TIRED, OR UNDER THE INFLUENCE OF DRUGS OR ALCOHOL.
Be mentally alert at all times when running machinery.
7. ONLY ALLOW TRAINED AND PROPERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make
sure operation instructions are safe and clearly understood.
8. KEEP CHILDREN AND VISITORS AWAY. Keep all children and visitors a safe distance from the work
area.
9. MAKE WORKSHOP CHILD PROOF. Use padlocks, master switches, and remove start switch keys.
Indicates an imminently hazardous situation which, if not avoided, WILL
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, COULD
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, MAY
result in minor or moderate injury.
This symbol is used to alert the user to useful information about proper
operation of the equipment, and/or a situation that may cause damage
to the machinery.
NOTICE

-6-
W1755 6" Parallelogram Jointer
SAFETY
10. NEVER LEAVE WHEN MACHINE IS RUNNING. Turn power OFF and allow all moving parts to come to
a complete stop before leaving machine unattended.
11. DO NOT USE IN DANGEROUS ENVIRONMENTS. DO NOT use machinery in damp, wet locations, or
where any flammable or noxious fumes may exist.
12. KEEP WORK AREA CLEAN AND WELL LIT. Clutter and dark shadows may cause accidents.
13. USE A GROUNDED EXTENSION CORD RATED FOR THE MACHINE AMPERAGE. Undersized cords over-
heat and lose power. Replace extension cords if they become damaged. DO NOT use extension cords
for 220V machinery.
14. ALWAYS DISCONNECT FROM POWER SOURCE BEFORE SERVICING MACHINERY. Make sure switch is in
OFF position before reconnecting.
15. MAINTAIN MACHINERY WITH CARE. Keep blades sharp and clean for best and safest performance.
Follow instructions for lubricating and changing accessories.
16. MAKE SURE GUARDS ARE IN PLACE AND WORK CORRECTLY BEFORE USING MACHINERY.
17. REMOVE ADJUSTING KEYS AND WRENCHES. Make a habit of checking for keys and adjusting wrench-
es before turning machinery ON.
18. CHECK FOR DAMAGED PARTS BEFORE USING MACHINERY. Check for binding and alignment of
parts, broken parts, part mounting, loose bolts, and any other conditions that may affect machine
operation. Repair or replace damaged parts.
19. USE RECOMMENDED ACCESSORIES. Refer to the instruction manual for recommended accessories.
The use of improper accessories may cause risk of injury.
20. DO NOT FORCE MACHINERY. Work at the speed for which the machine or accessory was designed.
21. SECURE WORKPIECE. Use clamps or a vise to hold the workpiece when practical. A secured
workpiece protects your hands and frees both hands to operate the machine.
22. DO NOT OVERREACH. Keep proper footing and balance at all times.
23. MANY MACHINES WILL EJECT THE WORKPIECE TOWARD THE OPERATOR. Know and avoid condi-
tions that cause the workpiece to "kickback."
24. ALWAYS LOCK MOBILE BASES (IF USED) BEFORE OPERATING MACHINERY.
25. BE AWARE THAT CERTAIN DUST MAY BE HAZARDOUS to the respiratory systems of people and ani-
mals, especially fine dust. Make sure you know the hazards associated with the type of dust you will
be exposed to and always wear a respirator approved for that type of dust.

-7-
W1755 6" Parallelogram Jointer
SAFETY
Additional Safety Instructions for Jointers
USE this and other machinery with caution
and respect. Always consider safety first,
as it applies to your individual working
conditions. No list of safety guidelines can
be complete—every shop environment is
different. Failure to follow guidelines could
result in serious personal injury, damage
to equipment or poor work results.
READ and understand this
entire instruction manual
before using this machine.
Serious personal injury
may occur if safety and
operational information is
not understood and fol-
lowed. DO NOT risk your
safety by not reading!
1. JOINTER KICKBACK. “Kickback” is when the workpiece is thrown off the jointer table by the force
of the cutterhead. Always use push blocks and safety glasses to reduce the likelihood of injury
from “kickback.” If you do not understand what kickback is, or how it occurs, DO NOT operate this
machine.
2. CUTTERHEAD ALIGNMENT. Keep the top edge of the outfeed table aligned with the edge of the knife
at top dead center (TDC) to avoid kickback and personal injuries.
3. PUSH BLOCKS. Always use push blocks whenever surface planing. Never pass your hands directly over
the cutterhead without a push block.
4. WORKPIECE SUPPORT. Proper workpiece support while cutting is crucial for making safe cuts and
avoiding injury. Never attempt to make a cut with an unstable workpiece.
5. KICKBACK ZONE. The “kickback zone” is the path directly through the end of the infeed table. Never
stand or allow others to stand in this area during operation.
6. MAXIMUM CUTTING DEPTH. The maximum cutting depth for one pass is 1⁄8". Never attempt any
single cut deeper than this!
7. JOINTING WITH THE GRAIN. Jointing against the grain or jointing end grain is dangerous and could
produce chatter or excessive chip out. Always joint with the grain.
8. KEEPING GUARDS IN PLACE. With the exception of rabbeting, all operations must be performed with
the guard in place. After rabbeting, be sure to replace the guard.
9. PROPER CUTTING. When cutting, always keep the workpiece moving toward the outfeed table until
the workpiece has passed completely over the cutterhead. Never move the workpiece backwards
toward the infeed table, or the risk of kickback will be extreme.
10. USING GOOD STOCK. Jointing safety begins with your lumber. Inspect your stock carefully before you
feed it over the cutterhead. Never joint a board that has loose knots, nails, or staples. If you have
any doubts about the stability or structural integrity of your stock, DO NOT joint it!

-8-
W1755 6" Parallelogram Jointer
SAFETY
Avoiding Potential Injuries
Figure 1. Correct operator and workpiece position,
guard is in place, and push blocks are being used.
Figure 2. Never surface plane without push
blocks!
Figure 3. Never plane/edge-joint with
the guard removed!
Figure 5. Never joint end grain!
Figure 4. Never stand directly behind the
workpiece!

-9-
W1755 6" Parallelogram Jointer
ELECTRICAL
DO NOT work on your electrical system
if you are unsure about electrical
codes and wiring! Seek assistance from
a qualified electrician. Ignoring this
warning can result in electrocution,
fire, or machine damage.
ELECTRICAL
We do not recommend using an extension cord; however,
if you have no alternative, use the following guidelines:
• Use a cord rated for Standard Service (S).
• Do not use a cord longer than 50 feet.
• Ensure that the cord has a ground wire and pin.
• Use the gauge size listed below as a minimum.
Extension Cords
110V/220V Operation
The Model W1755 is prewired for 110V operation, but
you can rewire it for 220V operation (refer to the wir-
ing diagram on Page 41). We recommend connecting this
machine to a dedicated circuit with a verified ground,
using the circuit size given below. Never replace a circuit
breaker with one of higher amperage without consulting
a qualified electrician to ensure compliance with wiring
codes.
This machine must be grounded! The electrical cord sup-
plied with this machine comes with a grounding pin. If
your outlet does not accommodate a ground pin, have it
replaced by a qualified electrician.
If you are unsure about the wiring codes in your area
or you plan to connect your machine to a shared cir-
cuit, you may create a fire or circuit overload hazard—
consult a qualified electrician to reduce this risk.
6-15P 6-15R
Figure 6. NEMA 5-20 and 6-15 plugs and
receptacles.
Operating Voltage Amp Draw Min. Circuit Size Plug/Receptacle Extension Cord
110V Operation 15 Amps 20A NEMA 5-15 12 Gauge
220V Operation 7.5 Amps 15A NEMA 6-15 14 Gauge
Electrical Specifications

-10-
W1755 6" Parallelogram Jointer
SETUP
READ and understand this
entire instruction manual
before using this machine.
Serious personal injury
may occur if safety and
operational information
is not understood and fol-
lowed. DO NOT risk your
safety by not reading!
The SHOP FOX® Model W1755 has been carefully pack-
aged for safe transporting. If you notice the machine has
been damaged, please contact your authorized SHOP
FOX® dealer immediately.
Unpacking
SETUP
SUFFOCATION HAZARD!
Immediately discard all plastic bags and
packing materials to eliminate suffoca-
tion hazards for children and animals.
UNPLUG power cord
before you do any assem-
bly or adjustment tasks!
Otherwise, serious per-
sonal injury to you or
others may occur!
The following items are needed, but not included, to set
up your machine:
• People for Lifting Help ...................................2
• Straightedge ................................................1
• Phillips Screwdriver #2 ...................................1
• Wrench or Socket 17mm .................................1
• Wrench or Socket 14mm .................................1
• Wrench or Socket 13mm .................................1
Items Needed for Setup

-11-
W1755 6" Parallelogram Jointer
SETUP
NOTICE
When ordering replacement parts, refer
to the parts list and diagram in the back
of the manual.
The following is a description of the items shipped with
the SHOP FOX® Model W1755.
Note: If you can't find an item on this list, check the
mounting location on the machine or examine the pack-
aging materials carefully. Occasionally we pre-install cer-
tain components for safer shipping.
Box 1: (Figure 7) Qty
A. Jointer Assembly ..........................................1
B. Carriage .....................................................1
C. Fence ........................................................1
D. Extension Table ............................................1
E. Push Blocks .................................................2
F. Cutterhead Guard .........................................1
G. Hex Wrenches 2.5, 4, 5, 6, 8mm ................ 1 Each
H. Handle .......................................................1
I. Fence Tilt Lever ...........................................1
J. Open-end Wrench 8/10, 12/14mm .............. 1 Each
K. Knife Setting Jig (not shown) ............................1
Box 2: (Figure 8) Qty
L. Stand Assembly w/Motor .................................1
M. Pedestal Switch ............................................1
N. Wheel Assembly ...........................................1
O. Belt Guard ..................................................1
P. Dust Port ....................................................1
Q. V-Belt ........................................................1
Assembly Fasteners Qty
• Hex Bolt M8-1.25 x 50 (Wheel/Stand) .................1
• Flat Washer 8mm (Wheel/Stand) .......................1
• Hex Bolts M10-1.5 x 55 (Wheel/Stand) ................2
• Flat Washers 10mm (Wheel/Stand) ....................2
• Hex Nuts M10-1.5 (Wheel/Stand) .......................2
• Cap Screws M8-1.25 x 25 (Jointer/Stand) .............4
• Lock Washers 8mm (Jointer/Stand) ....................4
• Flange Bolts M6-1 x 12 (Belt Guard) ...................2
• Hex Nuts M6-1 (Belt Guard) .............................2
• Flat Washers 6mm (Belt Guard) .........................2
• Cap Screws M6-1 x 20 (Extension Table) ..............2
• Cap Screw M10-1.5 x 30 (Carriage) .....................1
• Cap Screw M10-1.5 x 50 (Carriage) .....................1
• Flat Washers 10mm (Carriage) ..........................2
• Cap Screws M8-1.25 x 30 (Fence) .......................2
• Cap Screws M10-1.5 x 25 (Pedestal) ...................2
• Lock Washers 10mm (Pedestal) .........................2
• Flat Washers 10mm (Pedestal) ..........................2
• Phillips Screws M5-.8 x 16 (Dust Port) .................4
• Flat Washers 5mm (Dust Port) ..........................4
Inventory
Figure 8. Box 2 inventory.
LM
N
O
Q
P
Figure 7. Box 1 inventory.
A
H
B
D
EF
I
G
C
J
Power must not be connected to
machine during setup!

-12-
W1755 6" Parallelogram Jointer
SETUP
• Floor Load: This machine distributes a
heavy load in a small footprint. Some
residential floors may require additional
bracing to support both machine and
operator.
• Working Clearances: Consider existing and
anticipated needs, size of material to be
processed through the machine, and space
for auxiliary stands, work tables or other
machinery when establishing a location for
your Jointer.
• Lighting: Lighting should be bright enough
to eliminate shadow and prevent eye strain.
• Electrical: Electrical circuits must be
dedicated or large enough to handle
amperage requirements. Outlets must be
located near each machine, so power or
extension cords are clear of high-traffic
areas. Follow local electrical codes for
proper installation of new lighting, outlets,
or circuits.
MAKE your shop “child
safe.” Ensure that your
workplace is inaccessible
to youngsters by closing
and locking all entrances
when you are away. NEVER
allow untrained visitors in
your shop when assem-
bling, adjusting or operat-
ing equipment.
Cleaning Machine
The table and other unpainted parts of your
Jointer are coated with a waxy grease that
protects them from corrosion during shipment.
Clean this grease off with a solvent cleaner or
citrus-based degreaser. DO NOT use chlorine-
based solvents such as brake parts cleaner or
acetone—if you happen to splash some onto a
painted surface, you will ruin the finish.
Machine Placement
USE helpers or power lift-
ing equipment to lift this
6" Parallelogram Jointer.
Otherwise, serious per-
sonal injury may occur.
NEVER use gasoline or
other petroleum-based
solvents to clean with.
Most have low flash
points, which make them
extremely flammable.
A risk of explosion and
burning exists if these
products are used. Serious
personal injury may occur
if this warning is ignored!
ALWAYS work in well-
ventilated areas far from
possible ignition sources
when using solvents to
clean machinery. Many
solvents are toxic when
inhaled or ingested. Use
care when disposing
of waste rags and
towels to be sure they
DO NOT create fire or
environmental hazards.

-13-
W1755 6" Parallelogram Jointer
SETUP
To assemble the jointer, do these steps:
1. Carefully lay the stand on its side so you can access
the underside.
2. Use the M8-1.25 x 50 hex bolt and 8mm flat washer
to bolt the wheel assembly to the stand, as shown in
Figure 9.
3. Use the two M10-1.5 x 55 hex bolts, 10mm flat
washers, and M10-1.5 hex nuts to finish tightening
the wheel assembly to the stand, as shown in Figure
10.
4. Turn the stand rightside up and remove the back
cover.
Assembly
Figure 9. Bolting wheel assembly to stand.
Figure 10. Securing wheel assembly to
stand.
Figure 11. Securing the jointer to the
stand.
The jointer is very heavy. The
next step requires two strong
people or power lifting equipment
to lift the jointer.
5. Lift the jointer onto the stand and align the mount-
ing holes.
6. Use the provided four M8-1.25 x 25 cap screws and
8mm lock washers to secure the jointer to the stand,
as shown in Figure 11.

-14-
W1755 6" Parallelogram Jointer
SETUP
7. Loosen the motor bracket bolts shown by the black
arrows in Figure 12.
8. Put the V-belt on the motor pulley, then roll it onto
the cutterhead pulley, as shown in Figure 13.
9. Check the alignment of the pulleys to make sure the
V-belt is straight up and down.
— If the pulleys are aligned, go to Step 13.
— If the pulleys are NOT aligned, follow Steps 10–
12.
10. Remove the V-belt and loosen the motor mount bolts
shown by the white arrows in Figure 12.
11. Shift the motor horizontally as needed to align the
pulleys, and tighten the motor mount bolts.
12. Reinstall the V-belt on the pulleys.
13. Pull down on the motor with one hand to keep ten-
sion on the V-belt, and tighten the motor bracket
bolts with your other hand.
14. Push the center of the V-belt as illustrated in Figure
14, using moderate force. When tensioned correctly,
the deflection should be approximately 1⁄4".
— If the deflection is outside of this range, then
loosen the motor bracket bolts and repeat Steps
13–14.Figure 13. Rolling the V-belt onto the
cutterhead pulley.
Figure 12. Motor bracket bolts (black
arrows) and motor mount bolts (white
arrows).



Figure 14. Checking belt deflection.
NOTICE
Overly loose V-belts can slip on the pulleys and burn
up or cause poor machine performance. Overly tight
V-belts cause unecessary wear on the motor and
pully bearings, leading to a shortened lifespan.

-15-
W1755 6" Parallelogram Jointer
SETUP
16. Replace the cover on the back of the jointer stand.
17. Use the two M6-1 x 20 cap screws to attach the
extension table to the front of the jointer, as shown
in Figure 16. Leave the cap screws loose for now.
18. Using a straightedge, make the extension table flush
with the infeed table, then tighten the two cap
screws to secure the extension table in place.
Figure 16. Attaching extension table to
jointer.
NOTICE
The outfeed table MUST be level with the knives at
their highest point during rotation or the workpiece
will hit the outfeed table during operation. The
outfeed table height is factory set, but you MUST
check it before operation.
19. Place a straightedge on the outfeed table so it
extends over the cutterhead.
20. Carefully rotate the cutterhead pulley and notice if
the knife contacts the straightedge when the knife is
at its highest point in the rotation (top dead center
or TDC), as shown in Figure 17.
— The knife will barely touch the straightedge when
the outfeed table is set correctly. If the outfeed
table is set correctly, continue with the next step.
— If the knife lifts the straightedge or does not con-
tact the straightedge, the outfeed table must be
adjusted. Do the procedure in Setting Outfeed
Table Height on Page 35, then continue with the
next step in this section.
— If one knife is even with the outfeed table but
other knives are not, the height of the knives
must be adjusted evenly. See Adjusting/Replacing
Knives on Page 29.
Figure 17. Using a straightedge to make
sure outfeed table is level with knives at
their highest point of rotation (TDC).

 
Figure 15. Installing the belt guard.
The belt guard MUST be installed or the moving V-
belt will be exposed, creating an entanglement haz-
ard at the back of the jointer.
15. Install the belt guard with the two M6-1 x 10 flange
bolts, M6-1 hex nuts, and 6mm flat washers, as
shown in Figure 15.Belt Guard

-16-
W1755 6" Parallelogram Jointer
SETUP
Figure 19. Fence carriage mounted on the
back of the jointer.
Lock Handle
21. Attach the carriage to the back of the jointer with
the M10-1.5 x 30 cap screw on the infeed side, the
M10-1.5 x 50 cap screw on the outfeed side, and two
10mm flat washers. Leave the cap screws loose for
now.
22. Place three pieces of paper on the jointer bed, slide
the top half of the carriage over the paper, and
allow it to rest on the paper, as shown in Figure 18.
Note: The paper acts as a temporary shim for set-
ting the carriage height, so it won't scratch the
table when the fence is moved forward during regu-
lar operations.
23. Tighten the carriage mounting cap screws and dis-
card the paper.
24. Mount the lock handle on the carriage, as shown in
Figure 19.
25. Attach the fence to the carriage with the two M8-
1.25 x 30 cap screws, as shown in Figure 20.
26. Install the tilt lever in the fence (Figure 21).
Figure 20. Attaching fence to carriage.
Figure 21. Installing the tilt lever.
The cutterhead guard is a critical safety feature on
this machine—you MUST install and verify that it is
working as intended before using the jointer! Failure
to do this will greatly increase the chances of a seri-
ous injury when operating the jointer.
Figure 18. Carriage resting on paper to
prop it up during tightening.
Paper
27. Insert the cutterhead guard shaft into the hole at
the front of the infeed table, making sure that the
flat part of the shaft faces the set screw shown in
Figure 22.
28. Tighten the set screw against the shaft (see Figure
22) to secure the cutterhead guard in place.

-17-
W1755 6" Parallelogram Jointer
SETUP
29. Test that the cutterhead guard is working correctly
by pulling it back and letting go. The cutterhead
guard should quickly spring back over the cutterhead
when you do this.
— If the guard does not quickly spring back over
the cutterhead when you perform this test, then
remove it and repeat Steps 27–29. Do not con-
tinue with the assembly until the cutterhead guard
works correctly.
30. Use the two M10-1.5 x 25 cap screws, 10mm lock
washers, and 10mm flat washers to attach the ped-
estal switch to the back of the jointer, as shown in
Figure 23, then connect it to the motor cord.
31. Use the four M5-.8 x 16 Phillips head screws and
5mm flat washers to install the dust port on the
jointer stand, as shown in Figure 24.
Figure 23. Attaching pedestal switch to
the back of the jointer.
Figure 22. Securing the cutterhead guard.
Set Screw
Figure 24. Attaching dust port to jointer
stand.
Figure 25. Knife setting jig assembly.
DO NOT operate the Model W1755 without an ade-
quate dust collection system. This machine creates
substantial amounts of wood dust while operating.
Failure to use a dust collection system can result in
short and long-term respiratory illness.
Assemble the knife setting jig as shown in Figure 25.
Knife Setting Jig
Recommended CFM at Dust Port: ................ 400 CFM
Do not confuse this CFM recommendation with the rating
of the dust collector. To determine the CFM at the dust
port, you must take into account many variables, includ-
ing the CFM rating of the dust collector, the length of
hose between the dust collector and the machine, the
amount of branches or Y's, and the amount of other open
lines throughout the system. Explaining this calculation
is beyond the scope of this manual. If you are unsure of
your system, consult an expert or purchase a good dust
collection "how-to" book.
Dust Collection

-18-
W1755 6" Parallelogram Jointer
SETUP
Complete this process once you have familiarized yourself
with all instructions in this manual.
To test run the jointer, do these steps:
1. Read the entire owner's manual first to make sure
you are familiar with the safety and operation con-
trols of this machine!
2. Make sure all tools and foreign objects have been
removed from the machine.
3. Review Page 9 and connect your machine to the
power source.
4. Lift the OFF paddle on the switch and press the red
STOP button in all the way to make sure the switch
is reset.
5. Turn the jointer ON.
— The jointer should run smoothly with little or no
vibration.
— Immediately turn the jointer OFF if you suspect
any problems, and refer to Page 42 to trouble-
shoot/fix any problems before starting the jointer
again. If the source of an unusual noise or vibra-
tion is not readily apparent, contact our technical
support for help at [phone] or contact us
online at [email protected].
6. Press the STOP paddle to turn the jointer OFF.
Test Run
Projectiles thrown from the machine
could cause serious eye injury. Wear
safety glasses during assembly and
operation.
Loose hair and clothing could get
caught in machinery and cause serious
personal injury. Keep loose clothing
rolled up and long hair tied up and
away from machinery.