Woodstock Shop Fox W1669 User manual

INSTRUCTION MANUAL
Phone: [phone] • On-Line Technical Support: [email protected]
COPYRIGHT © DECEMBER 2003 BY WOODSTOCK INTERNATIONAL, INC. REVISED MARCH, 2018 (HE)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
MODEL
W1669/W1670
RADIAL DRILL PRESS
#6218CR Printed in China

WARNING
Some dust created by power sanding, sawing, grind-
ing, drilling, and other construction activities con-
tains chemicals known to the State of California to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement, and
other masonry products.
• Arsenic and chromium from chemically
treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well venti-
lated area, and work with approved safety equip-
ment, such as those dust masks that are specially
designed to filter out microscopic particles.

-1-
ASSEMBLY OPERATIONS MAINTENANCEELECTRICAL ADJUSTMENTSSAFETYINTRODUCTION
CONTENTS
INTRODUCTION ............................................................................................ 2
About the W1669 and W1670 Radial Drill Presses......................................................... 2
Woodstock Technical Support................................................................................. 2
SAFETY ...................................................................................................... 4
Standard Safety Instructions.................................................................................. 4
Additional Safety Instructions for Drill Presses ............................................................ 5
Avoiding Potential Injuries .................................................................................... 6
ELECTRICAL ................................................................................................ 7
110V Operation ................................................................................................. 7
Extension Cords ................................................................................................. 7
Grounding........................................................................................................ 7
ASSEMBLY .................................................................................................. 8
Base and Column ............................................................................................... 9
Table Support ................................................................................................. 10
Headstock...................................................................................................... 12
Drill Chuck and ............................................................................................... 13
Spindle ......................................................................................................... 13
ADJUSTMENTS ............................................................................................14
Belt Tension ................................................................................................... 14
Feed Shaft Spring Tension................................................................................... 15
Quill-Shaft Screw ............................................................................................. 16
Table............................................................................................................ 17
OPERATIONS...............................................................................................18
Test Run ........................................................................................................ 18
Headstock...................................................................................................... 19
Changing Drill Bits............................................................................................ 20
Speed Changes ................................................................................................ 21
Drill Press RPM Chart......................................................................................... 22
Drilling Depth ................................................................................................. 22
Drill, Cutter, and Hole Saw Suggested RPM Chart .................................................. 23
MAINTENANCE ............................................................................................25
General......................................................................................................... 25
Table and Base ................................................................................................ 25
Lubrication .................................................................................................... 25
Troubleshooting ............................................................................................... 26
W1669 and W1670 Drill Press 110V Wiring ............................................................... 27
W1669 and W1670 Parts ..................................................................................... 28
W1669 Parts ................................................................................................... 30
W1670 Parts ................................................................................................... 32
Accessories .................................................................................................... 34
Notes ........................................................................................................... 36
Warranty ....................................................................................................... 38

-2-
The SHOP FOX®Model W1669 and W1670 Radial Drill Presses have been specially designed by
Woodstock International, Inc. to provide many years of trouble free service. Close attention to detail,
ruggedly built parts and a rigid quality control program assure safe and reliable operation.
The Model W1669 and W1670 Radial Drill Presses are capable of a wide variety of drilling and sanding
operations. Purchasing the D2677 Drum Sander Set and D2722 Mandrel allows you to sand small or finely
detailed pieces. The tilting table and headstock allows surfaces to be sanded and drilled at many different
angles. The Model W1669 and W1670 is packaged with a drill chuck, motor and paddle switch with remov-
able safety key.
Woodstock International, Inc. is committed to customer satisfaction in providing this manual. It is our
intent to make sure all the information necessary for safety, ease of assembly, practical use and dura-
bility of this product be included.
Woodstock Technical Support
About the W1669 and W1670 Radial Drill Presses
INTRODUCTION
INTRODUCTION
We stand behind our machines! In the event that questions arise about your machine, parts are miss-
ing, or a defect is found, please contact Woodstock International Technical Support at 1-360-734-3482 or
send e-mail to: [e-mail]. Our knowledgeable staff will help you troubleshoot prob-
lems and send out parts for warranty claims.
If you need the latest edition of this manual, you can download it from http://www.shopfox.biz.
If you still have questions after reading the latest manual, or if you have comments please contact us at:
Woodstock International, Inc.
Attn: Technical Support Department
P.O. Box 2309
Bellingham, WA 98227

-3-
Motor Type: ...................................................... TEFC Capacitor Start Induction
Motor:.............................................. 1⁄2 HP, 110V, 5 Amp., Single-Phase ⁄ 60 Hz
RPM: .............................................................................................. 1725
Power Transfer: ........................................................................ V-Belt Drive
Bearings: ................................................... Shielded & Lubricated Ball Bearings
Switch: ............................................ Toggle ON/OFF Switch, w/ Safety Lock Key
Spindle Travel: .................................................................................3-1⁄4''
Maximum Distance, Spindle to Base: ......................... W1669 = 15-1⁄2,'' W1670 = 49''
Maximum Distance, Spindle to Table: .................... W1669 = 9-1⁄4,'' W1670 = 31-1⁄2''
Overall Height: ..............................................W1669 = 31-1⁄2,'' W1670 = 64-1⁄2''
Head Tilt: .......................................................................45° Left, 90° Right
Table Tilt: ....................................................................... 90° Left and Right
Table Rotation: .................................................................................. 360°
Spindle Taper: ...................................................................................JT-33
Swing:............................................................................................... 34''
Chuck Size: ..........................................................5⁄8'' (1-13mm JT-33), Keyed
Speeds: ........................................................................... 5, Belt Controlled
Range of Speeds: ...................................................
550, 880, 1570, 2490, 3470 RPM
Drilling Capacity: ..........................................................1⁄2'' Diameter in Steel
Approximate Shipping Weight:.......................... W1669 = 100 lbs., W1670 = 150 lbs.
Specifications
INTRODUCTION

-4-
READ MANUAL BEFORE OPERATING MACHINE
FAILURE TO FOLLOW INSTRUCTIONS BELOW WILL
RESULT IN PERSONAL INJURY
1. Thoroughly read the instruction manual before operating your machine. Learn the applications,
limitations and potential hazards of this machine. Keep manual in a safe, convenient place for
future reference.
2. Keep work area clean and well lighted. Clutter and inadequate lighting invite potential hazards.
3. Ground all tools. If a machine is equipped with a three-prong plug, it must be plugged into a
three-hole electrical outlet or grounded extension cord. If using an adapter to aid in accommodat-
ing a two-hole receptacle, ground the adapter using a screw to a known ground.
4. Wear eye protection at all times. Use safety goggles with side shields or safety goggles, meeting
the national safety standards, while operating this machine.
5. Avoid dangerous environments. DO NOT operate this machine in wet or open flame environ-
ments. Airborne dust particles could cause an explosion and severe fire hazard.
6. Ensure all guards are securely in place and in working condition.
7. Make sure switch is in the “OFF” position before connecting power to machine.
8. Keep work area clean; free of clutter, grease, etc.
9. Keep children and visitors away. All visitors should be kept at a safe distance away while operat-
ing unit.
10. Childproof your workshop with padlocks, master switches, or by removing starter keys.
11. Disconnect the machine when cleaning, adjusting, or servicing.
Indicates an imminently hazardous situation which, if not avoided, WILL
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, COULD
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, MAY
result in minor or moderate injury and damage to the machine. It may
also be used to alert against unsafe practices.
This symbol is used to alert the user to useful information about proper
operation of the equipment.
NOTICE
SAFETY
Standard Safety Instructions
SAFETY

1. DRILL PRESS SPEEDS. Always operate your drill press at speeds that are appropriate for the drill
bit size and the material that you are drilling.
2. DRILLING HOLES. Feed the drill bit evenly into the workpiece. Back the bit out of deep holes and
clear the chips with a brush after you have turned the machine off.
3. USING THE CORRECT DRILL BITS. Use only round, hex or triangular shank drill bits, and make sure
the drill bit you are using is tightened properly..
4. SAFE MAINTENANCE. Never do maintenance or change speeds with this machine plugged in.
5. USING SERVICEABLE TOOLS. Never use tools that are in poor condition. Cutting tools that are dull
or damaged are difficult to control and may cause serious injury.
6. DRILLING OPERATIONS. Never hold a workpiece by hand while drilling, never drill sheet metal
unless it is clamped securely to the table, and always secure the workpiece to the table before
drilling.
7. SECURING A WORKPIECE. Properly position workpieces to avoid drilling into the table.
8. PROTECTING YOUR EYES. A face guard used or safety goggles is recommended.
9. WORKING HABITS. Habits – good and bad – are hard to break. Develop good habits in your shop and
safety will become second-nature to you.
-5-
12. DO NOT force the tool. The machine will do a safer and better job at the rate for which it was
designed.
13. Use correct tool. DO NOT force machine or attachment to do a job for which it was not designed.
14. Wear proper apparel. DO NOT wear loose clothing, neck ties, gloves, jewelry; and tie back hair.
15. Remove adjusting keys and wrenches. Before turning the machine on, make it a habit to check that
all adjusting keys and wrenches have been removed.
16. Use proper extension cord. When using an extension cord, make sure it is in good condition.
When extension cord is 100 feet and less in length, use those that are rated Standard Service
(grade S) or better, and that have a conductor size of 16 AWG. A drop in line voltage, loss of
power and overheating can result when using an undersized cord. The extension cord should have a
ground wire and ground plug pin, as well.
17. Keep proper footing and balance at all times.
18. DO NOT leave machine unattended. Wait until it comes to a complete stop before leaving the area.
19. Perform machine maintenance and care. Follow lubrication and accessory attachment instruc-
tions in the manual.
20. Keep machine away from open flame. Operating machines near pilot lights and/or open flames
creates a high risk if dust is dispersed in the area. Dust particles and an ignition source may cause
an explosion. DO NOT operate the machine in high risk areas, including but not limited to, those
mentioned above.
Additional Safety Instructions for Drill Presses
SAFETY

Figure 1. Never drill while holding the
workpiece by hand.
Figure 2. Keep fingers away from spinning
drill bits, cutters, and sanding surfaces.
Figure 3. Remove switch safety key when not
in use.
-6-
Avoiding Potential Injuries
SAFETY

-7-
Ground this machine! The electrical cord sup-
plied with the W1669 and W1670 Radial Drill
Press comes with a grounding pin. DO NOT
remove the pin if your outlet does not accept a
ground pin, see Figure 4. Have the outlet box
replaced by a qualified electrician or have an
appropriate adapter installed.
Remember, an adapter with a grounding wire
does not guarantee the machine will be ground-
ed. A ground source must always be verified in
the electrical circuit within the wall or conduit.
Grounding
ELECTRICAL
110V Operation
The SHOP FOX®W1669 and W1670 Radial Drill
Presses operate at 110 volts only. The motor
supplied with your new drill press is rated at
1⁄2 HP and will draw approximately 5 amps.
When choosing an outlet for this machine, con-
sider using one with a 15 amp circuit breaker
or fuse. Keep in mind that a circuit being used
by other machines or tools at the same time
will add to the electrical load being applied by
the drill press. Add up the load ratings of all
machines on the circuit. If this number exceeds
the rating of the circuit breaker or fuse, use a
different outlet.
DO NOT modify an existing low-amperage
circuit by only replacing the circuit breaker
with a breaker rated for a higher amperage.
The breaker and the complete circuit must be
replaced by a qualified electrician.
Any electrical outlet and
circuit that you plug your
machine into must be
grounded. Serious injury
and/or fire may occur if this
warning is ignored!
Figure 4. Never remove a grounding pin.
If you must use an extension cord, use the guide-
lines below to determine the correct cord length
and gauge. If you use an undersized-gauge exten-
sion cord or one that is too long, heat will gener-
ate in the cord and fire or circuit damage may
result.
•Use a cord rated for Standard Service (Grade S)
•Use a cord that is 16 gauge and 100 feet or
less
•Use a cord with a ground wire and pin
•Use only undamaged cords
Extension Cords
ELECTRICAL

-8-
EYE HAZARD!
Wear safety goggles during
all assembly procedures.
Otherwise serious personal
injury may occur!
ASSEMBLY
Figure 5. Component inventory.
A. Headstock Assembly
B. Base
C. Column
D. Table
E. Table Bracket Assembly
F. Drill Chuck and Key
G. Spindle Handles and Knobs (3)
H. W1669: Hex Wrenches 3MM,
5MM, 10MM
I. Column Bolts (4)
J. Belt Cover Knob and Screw
K. Lift Handle Crank
L. Pinion Gear
M. Lock Handles (4)
N. Rack
O. Column Ring
P. Open End Wrench (Not shown)
Q. W1670: Lock Lever
G
D
OL
I
C
N
S
H
M
K
E
F
J
B
Q
Use the list below and Figure 5 to inventory your shipment before beginning assembly. If any parts
are missing, call Woodstock International, Inc. at 360-734-3482 or [email protected].
While the main components of the SHOP FOX®W1669 and W1670 Drill Presses are assembled at the fac-
tory, some assembly is required. The following order of procedures is the recommended sequence.
R. W1670: Table Support Arm
Bracket
S. W1670: Hex Wrenches, 3MM
and 5mm
T. Mounting Hardware
(Refer to the parts list on
Page 30 for details)
Use the parts list at the back of
this manual when ordering parts.
SUFFOCATION HAZARD!
Immediately discard all plastic
bags and packing materials to
eliminate a suffocation haz-
ard for children and animals.
R
T
A
ASSEMBLY

-9-
Figure 6. Secure base to floor.
Figure 7. Secure base to 4' x 4' x 3⁄4" plywood.
Base and Column
1. UNPLUG THE MACHINE!
• If installing the W1670 to a concrete
floor, do these steps:
a. Position the drill press in a sensible work
area where the base sits flat at all four
corners, or the base may crack when you
tighten the fasteners.
b. Mark and drill the floor, and install the
concrete anchor bolts (not included) (see
Figure 6).
c. Position the base and fasten the base to
the floor carefully as not to crack it.
• If installing the W1670 to a plywood
base, do these steps:
a. Center the drill press base along the back
edge of the 4' x 4' x 3⁄4" sheet of plywood
(see Figure 7).
b. At each corner of the drill press base, drill
the plywood.
c. Secure the base to the plywood with four
3/8" diameter bolts, washers, and nuts
(not included).
• If installing the W1669 to a tool table
or workbench, do these steps:
a. Position the base on a bench or tool table
capable of supporting approximately 100
lbs.
b. Drill two mounting holes (Figure 8), and
secure the base to the table with the two
supplied carriage bolts and wing nuts.
2. Place the column on the base, and install the
four column bolts supplied.
For maximum stability, secure the W1670
floor-model drill press to a sturdy surface like
a floor or a 4' x 4' x 3⁄4" piece of plywood. For
the W1669 bench-model, secure it to a sturdy
workbench or tool table.
TIPPING HAZARD!
Never mount a drill press to a
mobile base. Mount the drill
press base to a sturdy surface
or the drill press may tip and
cause injury.
Figure 8. Workbench mounting holes.
Mounting
Holes
ASSEMBLY

-10- Figure 11. Installing rack and table bracket.
Figure 10. Align set screw with flat pad on
pinion.
Table Support
The W1669 comes with a one geared table
bracket. The W1670 comes with a geared table
bracket and table support arm, which allows
the distance between the column and table to
be adjusted. No table support parts are inter-
changeable between the two drill presses.
To install the table support assembly, do
these steps:
1. Insert the table lock lever through the un-
threaded hole (see Figure 9) in the table
bracket, and then tighten the lever into
the threaded side exactly three turns.
2. Starting with the pinion gear, insert the
shaft into the table bracket and mesh the
teeth with the worm gear as shown in
Figure 9.
3. Align the set screw in the crank handle
with the flat pad on pinion shaft.
4. Tighten the 3mm set screw to lock the
handle in place (see Figure 10).
5. Examine the rack and note that the rack
teeth at one end are cut closer to the end
of the rack than the other.
6. Insert the rack through the table bracket
so the end that has the rack teeth cut clos-
er to the end is pointing down (see Figure
11).
7. Hold the rack against the worm gear and
slide the table bracket and rack onto the
column (see Figure 11).
Figure 9. Pinion and worm gear installation.
Pinion
Gear
Worm
Gear
Un-threaded Hole
Flat
Pad
Set Screw
ASSEMBLY

Figure 13. Column ring in the correct position.
8. Seat the rack tapered-point into the bevel
that is cut into the column support tube
(see Figure 12).
9. Slide the column ring onto the column with
the inside bevel in the down position until
the rack tapered-point seats into the bevel
(see Figure 13).
10. Position the column ring so the table
bracket and rack can just rotate around
the column without binding.
11. Carefully, snug the set screw to hold the
column ring in place. Over-tightening the
column ring will distort or split the column
ring.
Column Ring
Bevel
Figure 12. Bevel and rack seated correctly.
Tapered Rack
Point and
Column Support
Tube Bevel.
Set
Screw
ASSEMBLY
-11-

-12-
GET help to lift the head-
stock, or you may seri-
ously hurt your back or
drop the headstock.
The headstock is secured with a set screw so it
is aligned with the drill press base for balance
and weight distribution. DO NOT over tighten
the set screw, or you will bend the column or
strip the threads.
Headstock
To install the headstock assembly, do these
steps:
1. Place the locking gib into the recessed
pocket on the inside of the column bracket
casting (see Figure 14).
2. With an assistant, lift and position the
headstock pocket over the column and
allow the headstock to slide down until
the column fully seats into the headstock
(approximately 2", see Figure 15).
3. Rotate the headstock directly over the foot
of the base as viewed from the front of the
drill press.
4. Screw in the two lock handles on the sides
of the headstock.
5. Using a plumb bob and ruler, center the
headstock with the base, and tighten the
two set screws to secure the headstock to
the column (see Figure 16).
Figure 14. Locking gib installation.
Figure 15. Headstock-to-column installation.
Figure 16. Aligning the headstock.
Locking
Gib
ASSEMBLY

-13-
Drill Chuck and
Spindle
Your keyed drill chuck attaches to the drill
spindle. When properly joined, the JT-33
tapers on the spindle and inside the chuck cre-
ate an almost permanent connection.
To install the drill chuck, do these steps:
1. Clean the drill chuck and spindle with min-
eral spirits and follow all safety warnings
on the container (see Figure 17).
Note: Failure to clean the tapered mating
surfaces of the spindle and drill chuck may
result in a loose or wobbly chuck.
2. Use the provided chuck key to adjust the
jaws of the chuck until they are inside of
the drill chuck body (see Figure 18).
3. Place the drill chuck on the spindle and tap
the chuck onto the spindle with a block of
wood or a dead-blow hammer (see Figure
18). DO NOT use a metal hammer to seat
the drill chuck onto the spindle!
Figure 18. Seating chuck into spindle.
Figure 17. Clean the chuck before installation.
Chuck Jaws
Recessed and
Protected
Inside of
Chuck
ASSEMBLY

-14-
ADJUSTMENTS
Belt Tension
During the life of your drill press you will use differ-
ent belt and pulley combinations. No matter which
pulley combination you use, make sure that the belt
is tensioned properly
To adjust the drive belt tension, do these
steps:
1. UNPLUG THE DRILL PRESS!
2. Open the belt safety cover (see Figure
19).
3. Loosen both motor lock knobs at the side
of the headstock (see Figure ).
4. Slide the motor away from the headstock
until the belt is taut.
5. Hold the motor in position, and tighten the
lock screw, and make sure the belt deflec-
tion gap is correct when pinched together
between the pulleys (see Figure 21).
• If the gap between both inner sides of
the belt is greater or less than 3⁄4" repeat
Steps 3-5until the deflection gap is 3⁄4".
• If the deflection gap is 3⁄4"the belt is ten-
sioned correctly.
6. Close the belt safety cover.
UNPLUG the drill press
before any assembly,
adjustment, maintenance,
or belt changing proce-
dures. Otherwise serious
personal injury may occur!
Figure 19. Open belt safety cover.
Figure 20. Motor lock knob.
Figure 21. Measuring belt deflection.
Motor
Lock Knob
Push rod
Belt Deflection
gap should be
about 3⁄4"
ADJUSTMENTS

-15-
Figure 23. Typical spring cover lock slot and
locking lug.
Spring-Cover
Lock Slot
Locking Lug
Figure 22. Feed shaft return spring assembly.
Spring
Lock Cover
Jam Nut
and
Cover Nut
The feed shaft return spring is adjusted at the fac-
tory; however, during the life of the drill press you
may want to adjust the feed shaft return spring to
a greater tension for a stronger quill return.
To adjust the feed shaft spring tension, do
these steps:
1. UNPLUG THE DRILL PRESS!
2. Wipe off any oil on the spring-lock cover so
it will not slip when you hold the cover from
spinning (see Figure 22).
3. Make sure the quill is completely seated and
the depth stop reads zero.
4. Put on thick leather gloves, and hold the
spring cover against the side of the head-
stock so the cover stays splined with the
locking lug; remove the jam nut and loosen
the cover nut approximately 1⁄4" (6.4mm).
5. Pull the cover outward just enough to dis-
engage the spring-cover lock slot from the
locking lug (see Figure 23).
6. Rotate the cover counterclockwise to
increase spring tension, or let the cover
slowly unwind in the clockwise direction to
reduce spring tension (see Figure 23).
Feed Shaft Spring
Tension
WEAR safety goggles and
gloves when adjusting the
feed shaft spring. Serious
injury may occur if this
warning is ignored!
ADJUSTMENTS
Locking Lug

While you may never have to adjust the quill-
shaft screw, you should understand its func-
tion and know how to adjust it should you ever
need to remove the quill for cleaning. This
screw prevents the quill from rotating during
drilling and sanding procedures, and if adjusted
incorrectly, the quill may have lash or bind.
To adjust the quill-shaft screw, do these steps:
1. UNPLUG THE DRILL PRESS!
2. Clean and lubricate the quill shaft with a
thin coat of light oil, so the quill travels
freely (see Figure 25).
3. Loosen the jam nut (see Figure 26).
4. Move the quill up and down through the
entire range of travel, and turn the quill-
shaft screw inward as far as it can go with-
out binding the quill.
5. Tighten the jam nut, and check the quill
movement for binding or play while moving
the quill up and down through its entire
range of travel.
6. Re-adjust the quill-shaft screw as required.
Figure 25. Clean and oil quill shaft.
Figure 26. Quill-shaft screw and jam nut.
Quill-Shaft
Screw
Jam
Nut
7. Engage the next available spring-cover
lock slot with the locking lug and hold the
spring lock cover tightly against the side of
the headstock (see Figure 24).
8. Snug the cover nut against the spring cover
just until the nut stops, and then back-
off the nut approximately 1⁄3turn, or just
enough so there is no binding anywhere
along spindle travel path.
9. Hold the cover nut and tighten the jam nut
against the cover nut.
-16-
Figure 24. Hold the spring cover tightly.
Cover Nut
Quill-Shaft Screw
Lock Lug
ADJUSTMENTS

-17-
Table
The table can be adjusted for height, rotation,
and angle. The W1670 adds the fourth adjust-
ment of table distance from column.
Note: Table or table support parts are not
interchangeable between the W1669 and the
W1670 drill presses (see Figures 27 and 28).
To adjust the table, do these steps:
1. Loosen the table lock lever.
2. Turn the hand crank to raise or lower the
table.
3. Tighten the table lock lever.
4. For the W1670, loosen the table tilt lock
bolt (see Figure 29); or for the W1669,
loosen the cap screw.
5. Turn the index pin draw nut clockwise and
draw the index pin out of the casting until
you can rotate the table to your desired
angle (see Figure 29).
Note: Use this index pin only for indexing
the table to the “Zero degree” position.
Note: To index the table back to the zero
position, back off the draw nut, turn the
table to zero, tap the index pin back into
the casting, and tighten the table tilt lock
bolt.
6. Tighten the tilt table lock bolt or cap
screw, and double check your angle.
Figure 27. W1669 Table support assembly.
Figure 28. W1670 Table support assembly.
Figure 29. Tilt mechanism and lock bolt.
Table-Tilt
Lock Bolt
(W1670)
or
Table-Tilt
Lock Cap
Screw
(W1669)
Index Pin
and
Draw Nut
Tilt
Scale
ADJUSTMENTS

-18-
This drill press will perform many types of oper-
ations that are beyond the scope of this manual.
Many of these operations can be dangerous or
deadly if performed incorrectly.
The instructions in this section are written with
the understanding that the operator has the
necessary knowledge and skills to operate this
machine. If at any time you are experiencing
difficulties performing any operation, stop using
the machine!
If you are an inexperienced operator, we
strongly recommend that you read books, trade
articles, or seek training from an experienced
lathe operator before performing any unfamiliar
operations. Above all, your safety should come
first!
To start the drill press, do these steps:
1. Make sure the starting switch paddle is
down for OFF.
2. Make sure all fasteners and lock handles are
tight.
3. Make sure the drill chuck key is removed.
4. Plug in the power cord.
5. Lift the ON/OFF switch to start the drill
press, and make sure that your fingers are
poised near the paddle, as shown in Figure
30. In case there is a problem you can turn
the drill press off.
6. Observe and listen to the drill press, it
should run smoothly, with little or no vibra-
tion or rubbing noises.
• If you hear strange or unusual noises, shut
the drill press OFF, and wait for the spin-
dle to stop moving.
7. Unplug the drill press and refer to the
“Troubleshooting” table on Page 27
to help isolate and correct the problem
before using the drill press again.
Figure 30. Fingers poised near the stop switch.
WEAR safety goggles and
a respirator during drill-
ing or sanding opera-
tions. Otherwise seri-
ous personal injury may
occur!
Keep your shop “Child
Safe.” Always remove
the switch safety key
when drill press is not in
use. Serious injury may
occur.
Test Run
OPERATIONS
OPERATIONS