Worden MS.M.4.RT series User manual

MySpot Installation Manual
8/9/2010 Page 1 of 34
Assembly instructions for all catalog numbers beginning with:
MS.M.4.RT
MS.C.4.RT
(Right hand four seat quad with right hand tablets and with a 48” high back panel)
Tools required for assembly:
#2 Phillips screw driver
#3 Phillips screw driver
Slotted screw driver
5/32” hex wrench
3/16” hex wrench
6mm hex wrench
5/16” open end wrench
Hammer
Needle nose pliers
Power screw driver (optional)

8/9/2010 Page 2 of 34
Parts required to assemble (1) unit:
(4) – Back panels
(47-3/4”H x 29-13/16”W)
(1) – Center post
(2-1/4”SQ x 47-3/4”H)
(4) – Outer back cover panels
(40-9/16”H x 27-9/16”W)
(4) – Inner back cover panels
(31-7/8”H x 27-9/16”W)

8/9/2010 Page 3 of 34
Parts required to assemble (1) unit (continued):
(4) – Internal end panels
(21-1/16”H x 22-1/2”W)
(4) – End left face cover panels
(21-3/16”H x 22-1/2”W)
(4) – End right face cover panels
(21-3/16”H x 22-1/2”W)
(4) – Seat support beams
(28-1/2”L)

8/9/2010 Page 4 of 34
Parts required to assemble (1) unit (continued):
(4) – Right front legs
(2-1/4”SQ x 24-3/16”H)
(4) – Right hand tablet assemblies
(4) – Right arms
(6”W x 28-1/2”L)
(4) – Bottom panels
(23-5/8” x 27-3/8”)

8/9/2010 Page 5 of 34
Parts required to assemble (1) unit (continued):
(4) – Back cushions
(4) – Seat cushions
(4) – Z-bars (21-3/16”L)
(4) – Pin-fast brackets

8/9/2010 Page 6 of 34
Hardware required to assemble (1) unit (shown actual size):
(16) 1/4-20 x 3/4” pan head machine screws – zinc (part# 1001501)
(8) 5/16-18 x 1-1/2” pan head machine screws – black (part# 1000173)
(8) 5/16-18 x 1” flat head socket cap screws – black (part# 26797)
(4) 1/4-20 x 85mm (3-3/8”) decorative head bolt – black (part# 26506-BLK)
(16) #12 x 3/4” flat head wood screws – zinc (part# 26791)
(28) #10 x 1-1/4” flat head wood screws – black (part# 1001591)
(24) #8 x 5/8” pan head wood screws – black (part# 1001742)
(32) #12 x 5/8” pan head wood screws – black (part# 4300-1738)

8/9/2010 Page 7 of 34
Hardware required to assemble (1) unit (shown actual size) (continued):
(8) #12 x 1” pan head wood screws – black (part# 1001739)
(64) #14 x 3/8” shoulder screws – zinc (part# 26794)
(40) Cam pins – nickel (part# 29989)
(4) 1/4-20 barrel nut – steel (part# 20434)
(40) Cams – zinc (part# 29988)
(8) 5/16” flat washers – black (part# 1001780)

8/9/2010 Page 8 of 34
Hardware required to assemble (1) unit (shown actual size):
(28) Figure-8 fasteners – zinc (part# 1001663)
(12) Lock clips – black plastic (part# 1000611)

8/9/2010 Page 9 of 34
1(12) #10 x 1-1/4” (12) Figure-8’s
Screw (3) Figure-8’s into the predrilled holes in
the bottom edge of each back panel.
1 2

8/9/2010 Page 10 of 34
2(16) 1/4-20 x 3/4"
Attach a Z-bar onto the inside of each back panel.
1 2

8/9/2010 Page 11 of 34
3(16) Cam pins
Screw (16) cam pins into the center post.
1 2

8/9/2010 Page 12 of 34
4(16) Cams
Fasten the back panels to the center post.
1
2
3
4

8/9/2010 Page 13 of 34
5 (8)Shoulderscrews
Screw (4) shoulder screws into (4) inner back cover panels.
1 2

8/9/2010 Page 14 of 34
6
Fasten the inner back cover panels to the back panels.
1 2 3

8/9/2010 Page 15 of 34
7(24) #8 x 5/8” (24) Lock clips
Attach (3) lock clips under each inner back cover panel.
1 2 3 4

8/9/2010 Page 16 of 34
8(12) Cam pins
Screw (3) cam pins into each back panel post.
1 2

8/9/2010 Page 17 of 34
9(16) #10 x 1-1/4” (16) Figure-8’s
Screw (4) Figure-8’s into the predrilled holes in
the bottom edge of the internal end panels.
1 2

8/9/2010 Page 18 of 34
10 (12) Cams
Fasten the internal end panels to the back panel posts.
1
2
3
4

8/9/2010 Page 19 of 34
11 (12) Cam pins
Screw (3) cam pins into each front leg.
1 2

8/9/2010 Page 20 of 34
12
Attach a right hand tablet assembly to each front leg.
1 2