Worden MySpot MS.M.2.39 User manual

MySpot Installation Manual
8/9/2010 Page 1 of 35
Assembly instructions for all catalog numbers beginning with:
MS.M.2.39
MS.C.2.39
(Double seat with right hand and left hand tablets and with a 39” high back panel)
Tools required for assembly:
#2 Phillips screw driver
#3 Phillips screw driver
Slotted screw driver
5/32” hex wrench
3/16” hex wrench
6mm hex wrench
5/16” open end wrench
Hammer
Needle nose pliers
Power screw driver (optional)
All manuals and user guides at all-guides.com
all-guides.com

8/9/2010 Page 2 of 35
Parts required to assemble (1) unit:
(1) – Back panel
(38-3/4”H x 68-3/4”W)
(2) – Outer back cover panels
(31-9/16”H x 31-7/8”W)
(2) – Inner back cover panels
(22-3/16”H x 31-7/8”W)
All manuals and user guides at all-guides.com

8/9/2010 Page 3 of 35
Parts required to assemble (1) unit (continued):
(2) – Internal end panels
(21-1/16”H x 22-1/2”W)
(2) – End left face cover panels
(21-3/16”H x 22-1/2”W)
(2) – End right face cover panels
(21-3/16”H x 22-1/2”W)
(1) – Seat support beam
(64-1/8”L)
All manuals and user guides at all-guides.com

8/9/2010 Page 4 of 35
Parts required to assemble (1) unit (continued):
(1) – Left front leg
(2-1/4”SQ x 24-3/16”H)
(1) – Right front leg
(2-1/4”SQ x 24-3/16”H)
LH RH
(1 each) - Left hand and right hand tablet assembly
(1) – Left arm
(6”W x 28-1/2”L)
(1) – Right arm
(6”W x 28-1/2”L)
All manuals and user guides at all-guides.com

8/9/2010 Page 5 of 35
Parts required to assemble (1) unit (continued):
(2) – Bottom panels
(23-5/8” x 27-3/8”)
(1) – Center table
(14-5/8”W x 25”D)
(2) – Back cushions
(2) – Seat cushions
(2) – Z-bars (21-3/16”L)
(4) – Pin-fast brackets
All manuals and user guides at all-guides.com

8/9/2010 Page 6 of 35
Hardware required to assemble (1) unit (shown actual size):
(8) 1/4-20 x 3/4” pan head machine screws – zinc (part# 1001501)
(4) 5/16-18 x 1” flat head socket cap screws – black (part# 26797)
(2) 1/4-20 x 85mm (3-3/8”) decorative head bolt – black (part# 26506-BLK)
(8) #12 x 3/4” flat head wood screws – zinc (part# 26791)
(14) #10 x 1-1/4” flat head wood screws – black (part# 1001591)
(2) #10 x 1-1/2” flat head wood screws – black (part# 1001592)
(8) #8 x 5/8” pan head wood screws – black (part# 1001742)
(18) #12 x 5/8” pan head wood screws – black (part# 4300-1738)
All manuals and user guides at all-guides.com
all-guides.com

8/9/2010 Page 7 of 35
Hardware required to assemble (1) unit (shown actual size) (continued):
(4) #12 x 1” pan head wood screws – black (part# 1001739)
(32) #14 x 3/8” shoulder screws – zinc (part# 26794)
(12) Cam pins – nickel (part# 29989)
(2) Cam pins – nickel (part# 1000336)
(2) 1/4-20 barrel nut – steel (part# 20434)
(12) Cams – zinc (part# 29988)
(2) Cams – black (part# 1000335)
All manuals and user guides at all-guides.com

8/9/2010 Page 8 of 35
Hardware required to assemble (1) unit (shown actual size) (continued):
(14) Figure-8 fasteners – zinc (part# 1001663)
(4) Lock clips – black plastic (part# 1000611)
All manuals and user guides at all-guides.com

8/9/2010 Page 9 of 35
1(6) #10 x 1-1/4” (6) Figure-8
Screw (6) Figure-8’s into the predrilled holes in
the bottom edge of the back panel.
1 2
All manuals and user guides at all-guides.com

8/9/2010 Page 10 of 35
2(8) 1/4-20 x 3/4"
Attach the Z-bars onto the inside of the internal back panel.
1 2
All manuals and user guides at all-guides.com