Workrite Ergonomics Advent ADV 6030 Series Programming manual

Workrite Ergonomics | 800.959.9675 www.workriteergo.com 1 of 8
0.373"
#2 Drive
0.190"
1/2"
0.133"
#10-32 Thread
0.322"
#2 Drive
0.115
"5/8"
0.164"
#8 Screw Size
Assembly & Installation Instructions:
Advent
ADV 6030-XX/ADV 7230-XX
ID Part Name Qty
A Worksurface, Advent (60" or 72") 1
B Modesty Panel, Advent (60" or 72") 1
CLeg Assembly, Left 1
DLeg Assembly, Right 1
E Cable Trough 1
F Cam Lock Dowels 6
G Cam Locks 6
H Cam Covers 6
I #12 × 1" Phillips Pan Head Screws 20
J #10-32 × ½" Phillips Pan Head
Machine Screws
4
K Control Box, 2 Leg, 120 V 1
L #10 × 1" Phillips Pan Head Screws 2
M Programmable Switch 1
N#8 × ⅝" Phillips Pan Head Screws 12
O Motor Cable 2
P Y-Cable 1
Q⅜" × ⅝" P-Loops 6
R3⁄16" × 13⁄16" P-Loops 3
S Power Module 1
T Power Cord, Type B, 3' (1 m) 1
E
F
K
OQR
ST
P
LMN
G H I J
C A
B
D

2 of 8 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
or
WARNING: Maximum loading of desk assembly is 125 lb. (57 kg.). Maximum loading includes any equipment placed upon it,
and/or suspended under it. Loading should be evenly distributed over the desk surface. “Payload Capacity” is the Workrite Ergonomics recommended
maximum loading
Advent
V = 100-240 VAC, 50/60 Hz / 3.6 A maximum
IMPORTANT SAFETY INSTRUCTIONS:
When using an electrical furnishing, basic precautions should always be followed, including the following:
Read all instructions before using this Advent Work center.
DANGER: To reduce the risk of electric shock, always unplug this Advent Workcenter from the electrical outlet before cleaning.
WARNING: To reduce the risk of burns, re, electric shock, or injury to persons:
1. Unplug from outlet before putting on or taking off parts.
2. Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled persons.
3. Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.
4. Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into
water. Return the furnishing to a service center for examination and repair.
5. Keep the cord away from heated surfaces.
6. Do not use outdoors.
7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
8. To disconnect, remove plug from outlet.
9. Each surface intended to support an equipment payload of 300 pounds.
FOR COMMERCIAL USE ONLY
SAVE THESE INSTRUCTIONS
Verify that you have all the tools needed for the assembly
You will need the following tools:
#2 tip Phillips screwdriver or drill/driver
#3 tip Phillips screwdriver or drill/driver
M4 tip bit or 4 mm Wrench (J)
If you do not have a Workrite worksurface, you will also need:
⅛" pilot drill bit
⁄" pilot drill bit
✓

3 of 8 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
1.1 Place Worksurface (A) upside down on a at, level, and sturdy assembly area. The pre-drilled surface should be
facing up.
1.2 The rectangular cutouts will be on the left rear side of the Worksurface.
1.3 Place the Right (D) and Left (C) legs on the Worksurface (A) resting on the Mounting Plate. The three standoffs
projecting from each leg are located at the rear of each leg respectively. These should face in toward the center of
the Advent workstation.
SETUP
2.1 Install three Cam Lock Dowels (F) per leg with a
Phillips screwdriver.
INSTALL CAM LOCK DOWELS
1
Worksurface
Mounting Plate
Left Leg
Right Leg
Standoffs
D
C
A
2
F
F
Cam Lock Dowels
Cam Lock Dowels
Left Leg
Right Leg
Phillips Screwdriver
Rectangular Cutouts
Front Edge of Worksurface
D
C

Workrite Ergonomics | 800.959.9675 www.workriteergo.com 4 of 8
CAUTION: Maintain a 90° angle between each
respective Leg and Modesty Panel while inserting Cam Lock Dowels,
Cam Locks, and during the tightening process. Try to maintain a 90° angle
between each Leg and the Modesty Panel while sliding it in, and when
moving/aligning it to the worksurface. The Modesty Panel can be damaged if
too much angle is introduced.
2.2 Align the Modesty Panel (B) with the cam lock holes facing
inward and slide the Modesty Panel onto the Cam Lock
Dowels in the Left Leg (C) Connect with 3 Cam Locks (G)
Tighten cam locks with a Phillip screws driver as indicated
by the arrow on the Cam Lock.
2.3 Repeat Step 2.2 with the Right Leg (D)
F
F
Cam Lock Dowels
Cam Lock Dowels
BModesty Panel
Right Leg
Left Leg
Cam Locks
Cam Lock Covers
Cam Locks
G
G
Phillips Screwdriver
H
D
C

5 of 8 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
3.1 Align the Left Leg (C) with the pre-drilled holes on
worksurface and loosely install 8 each #12 x 1"
Phillips Pan Head Screws (I).
3.2 Repeat Step 3.1 for Right Leg (D).
3.3 Tighten all #12 x 1" Phillips Pan Head Screws (I)
securely.
4.1 Align the Cable Trough (E) with the pre-drilled holes in
the top. Attach with 4 each #12 x 1" Phillips Pan Head
Screws (I) as shown and tighten loosely.
4.2 Next attach the Cable Trough to the Modesty Panel
with 4 each #10-32 × ½" Phillips Pan Head Machine
Screws (J) and tighten securely
4.3 Tighten down all wood screws to Worksurface.
ASSEMBLE LEGS
ASSEMBLE CABLE MANAGEMENT TROUGH
CAUTION: do not use an "Impact"
style electric screwdriver, this will apply too much torque
and damage or strip threads
CAUTION: do not use an "Impact"
style electric screwdriver, this will apply too much torque
and damage or strip threads
3
4
#12 × 1" Pan Head Wood Screws
#12 × 1" Pan Head Wood Screws
#10-32 × ½" Pan Head Machine Screws
I
Mounting Plate
4.1
4.2
Left Leg
Cable Management Trough
J
I
E
C

Workrite Ergonomics | 800.959.9675 www.workriteergo.com 6 of 8
5.1 Align the Control Box (K) with the pre-drilled holes in
the top in front of the center grommet hole. Face the A/C
power port to the left as shown. Attach the control box
to the top with 2 each #10 x 1" Phillips Pan Head Screws
(L) and tighten securely.
5.2 Mount the Programmable Switch (M) into the pre-drilled
holes as shown with 2 each #8 x ⅝" Phillip Pan Head
Screws (N) and tighten securely. Rout the switch cable
to the Control Box and plug in into Control Box.
5.3 Connect the Motor Cables (O) to the left and right legs
as shown. Attach the left and right 90 motor cable plug
to the control box as shown.
5.4 Connect Y Cable (P) to the control box as shown.
Connect the other ends of the Y-Cable to the Motor
Cables as shown.
MOUNT CONTROLLER, SWITCH, & CABLING
5
5.2
5.4
5.1
5.3
M
L#10 × 1" Pan Head Wood Screws
Programmable Switch
#8 × ⅝" Phillips Pan Head Screws
Control Box
Motor Cable
Y-Cable
K
AC Power Port
8-Pin Connector
N
O
P

7 of 8 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
6.1 Locate the small P-Loops (R) in the hardware kit (there are two sizes, large and small).
6.2 Open small P-Loops (R) and feed the Switch and Motor Cables into them at the screw hole positions provided.
6.3 Utilizing the #8 x ⅝" (N) wood screws, fasten each P-Loop down to the worksurface at the pre-drilled hole locations.
CABLE MANAGEMENT
7.1 With assistance (a two person job), rotate the Advent workstation onto its back (Modesty Panel side). Utilize a blanket
or other soft material to protect the surfaces from scufng or marring.
7.2 Continuing with the same assistance (two person job), rotate the Advent onto it feet in a fully upright position
7.3 Locate the Power Module (S).
7.4 Remove the thumb knobs and mounting brackets from each side of the Power Module (S).
7.5 Insert the Power Module (S) into the slot on the right side of the worksurface from the top. The power cord extending
from the Power Module (S) should be pointing to the right and should be fed through the slot rst.
7.6 Place each of the mounting brackets over the Power Module (S) studs and the corresponding thumb knob and tighten.
7.7 Adjust the foot glides at each corner of the Advent to level the worksurface. Adjustment may require use of pliers.
TURN WORKSTATION UPRIGHT & INSTALL POWER MODULE
CAUTION: Lifting or rotating the Advent requires two people to prevent injury.
6
7

Workrite Ergonomics | 800.959.9675 www.workriteergo.com 8 of 8
1500402 Rev A
8.1 Locate the 3' long Power Cord (T) in the hardware kit.
8.2 Install 3' Power Cord into the AC receptacle on the Advent Control Box (K).
8.3 Plug in the 3' Power Cord into one of the outlets under the desk in the Power Module (S).
8.4 Plug in the 9' Power Module Cord into a wall outlet.
8.5 Apply Large P-Loops (Q) as needed, positioning them with pressure sensitive adhesive backing.
INSTALL POWER CABLE
8
T3' Power Cord
KControl Box S
Power Module