Workrite Ergonomics Sierra HX User manual

Workrite Sierra HX™ & HXL™
Assembly Instructions for
2-leg Electric Workcenters
#1500215- Rev A

2 of 8 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Workrite Sierra HX & HXL Electric Workcenters - Assembly Instructions for 2-leg Tables
List of Parts, grouped by carton
Parts, sold separately
AWorksurface (size and shape differ) Qty: 1
Important Note!
You must complete
initialization (Step 12)
at the end of assembly
or your table WILL NOT
FUNCTION PROPERLY.
!
M4 mm Allen Wrench Qty: 1
ERear Bracket Qty: 1
SPower cord Qty: 1
NControl Qty: 1
QCable Spool Qty: 2
RCable Loops Qty: 10
OLeg Cable - 1 meter Qty: 2
GControl Leg Qty: 1
FCompanion Leg Qty: 1
BShort Bracket Qty: 4
HFeet Qty: 2
IFeet Glides Qty: 4
CLeft End Bracket Qty: 1
DRight End Bracket Qty: 1
J#M6 × 14 mm Flat Head Cap Screw
Qty: 20
K#12 × ¾" Pan Head Laminate Top Screw
Qty: 32
L #8×⅝"PanHeadScrew Qty: 12
or
or
PControl Box Qty: 1

or
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 3 of 8
Workrite Sierra HX & HXL Electric Workcenters - Assembly Instructions for 2-leg Tables
Verify that you have all the hardware and tools needed for the assembly.
Check your cartons against the list on page 2 to verify that you have all the parts needed. You will
also need the following tools:
#2 tip Phillips screwdriver or drill bit
#3 tip Phillips screwdriver or drill bit
If you do not have a Workrite worksurface, you will also need a:
⅛”pilotdrillbit
3 ⁄32”pilotdrillbit
Lay Legs (F and G) and Brackets (B,
C,DandE)ontheoor.
Attach Short & Medium Brackets
Attach Short (B) Brackets using Flat Cap Screws (J) to both legs.
Attach Right End Bracket (D) to sides of the right (Control) Leg (G) using Flat Cap Screws (J).
Attach Left End Bracket (C) to sides of the left (Companion) Leg (F) using Flat Cap Screws (J).Do
not tighten screws completely.
Note: the right leg will be on your left
and vice versa when the assembly
is seen upside down.
Left
(Companion) leg
Right
(Control) leg
front
G
C
B
F
D
E
B
B
D
C
J
J
J
E
To avoid stripping the threads,
always insert and make the rst
few turns of the screw BY HAND
with an Allen wrench (K), ensuring
it is in straight.
!
1
a
b
b
2

2⅞" 6⅛"
2⅞"
6⅛"
4 screws per
End Bracket
3 screws per
Short Bracket
4 of 8 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Workrite Sierra HX & HXL Electric Workcenters - Assembly Instructions for 2-leg Tables
Attach Base to Worksurface and Tighten Screws
If you do not have a Workrite
worksurface skip to step 4
If you have a Workrite worksurface:
Position leg assemblies to align mounting
holes in brackets to pre-drilled holes in
Top (A) then attach loosely using Pan
Head Top Screws (K). If you use an
electric screwdriver, be sure it is on the
lowest torque setting to avoid stripping
the holes in the top.
Tighten all screws connecting
brackets to leg assemblies.
Then tighten all screws attaching
brackets to top.
Continue to Step 5 .
Attach Base to Worksurface and Tighten Screws (continued)
If you do not have a
Workrite worksurface:
Position leg assemblies on
bottom side of worksurface
using measurements a
below.
Mark placement of mounting
holes,thenuse⅛"drillbit
to drill pilot holes at marked
locations. You may wish to
mark your drill bit so you
do not drill any more than
¾" deep and damage your
worksurface top.
Do not drill all the way
through worksurface! front
A
3
a
b
c
4
a
b
b
a
a
c
B
C
B
A
K
K

4 screws per
End Bracket
3 screws per
Short Bracket
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 5 of 8
Workrite Sierra HX & HXL Electric Workcenters - Assembly Instructions for 2-leg Tables
Attach loosely using Pan Head Top Screws
(K). If you use an electric screwdriver, be
sure it is on the lowest torque setting to
avoid stripping the holes in the top.
Tighten all screws connecting brackets to
leg assemblies.
Then tighten all screws attaching brackets
to top.
Attach Feet (sold separately) & Slides
Attach Feet (H) to bottom of legs with Flat Head
Cap Screws (J), using Allen Wrench (M) and tighten
securely. Be sure the longer end of the foot goes
towards the front of the table.
You may have purchased the Styled Feet, that attach
in the same fashion.
Attach Feet Glides (I) to bottom of feet. Do not screw
in all the way to allow for leveling in step 11
c
c
d
e
J
a
b
H
H
I
5
B
C
B
A
K
K
J
I

6 of 8 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Workrite Sierra HX & HXL Electric Workcenters - Assembly Instructions for 2-leg Tables
Attach Switch
If you have a Workrite worksurface:
Position the switch over the pilot holes near front
edge of worksurface.
If you do not have a Workrite worksurface:
For non-Workrite worksurfaces, align Switch (N)
sothatoutermostedgeofswitchisushwith
edge of worksurface. Pre-drill screw pilot holes
into underside of worksurface with 3⁄32”drillbit.
You may wish to mark your drill bit so you do not
drillanymorethan¾”deepanddamageyour
worksurface top.
Do not drill all the way through
worksurface!
Attach Switch (N) to underside of worksurface
usingthesmaller(#8×⅝”)PanHeadScrews
(L). You may have purchased the Standard
Control which attaches in the same fashion.
front
N
L
b
7
ab
Attach Control Box to Tabletop
Position Control Box (P).
If you have a Workrite tabletop:
Locate the four pilot holes for the Control Box and
proceed to Step b .
If you do not have a Workrite tabletop:
Place Control Box (P) in position and use a pencil to
mark pilot hole placement. Control Box should be placed
towards rear center of tabletop. Lay out Switch (N) and
Leg Cables (O) to be sure they all reach the Control Box.
Remove Control Box and drill pilot holes where marked.
Do not drill all the way through tabletop!
With Control Box positioned over pilot holes, attach with
four Pan Head Screws (K) as shown.
P
K
O
O
N
6
a
bb
aP

Workrite Ergonomics | 800.959.9675 www.workriteergo.com 7 of 8
Workrite Sierra HX & HXL Electric Workcenters - Assembly Instructions for 2-leg Tables
Connect Leg Cables to Control leg and Companion Leg
ConnecttheLegCable(O)tothesixpositionconnectorlabeled”1”onboththeControlLegandthe
Companion Leg (F).
InsertthePowerCord(Q)intothetwopositionconnectorlabeled“DC”ontheControlBox(P).
InserttheSwitchCable(N)intothedataconnectorlabeled“A1”ontheControlBox(P).
Attach Cable Spools and Cable Loops
Attach Cable Spool (Q) with the #12 × ¾"Pan Head Laminate screw (K) and Cable Loops (R) to
undersideofworksurfaceusing#8×⅝"PanHeadScrew(L)makingsuretowraptheCableLoop
around the cable prior to attaching. If you do NOT have a Workrite worksurface, mount cable
spools in a convenient location between legs and control box.
LQ
R
R
R
R
O
O
K
8
9
Q
K
P
N

8 of 8 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Workrite Sierra HX & HXL Electric Workcenters - Assembly Instructions for 2-leg Tables
Initialize Legs
After all legs and the switch are connected, and the power cord has been plugged in, hold the
down arrow on the switch until the legs make a short motion down and then back up. This
initializes and synchronizes the table legs.
Adjust Feet Guides
If necessary, adjust leveling guides on table feet to level the worksurface. Unscrew to increase
height, screw in to decrease height.
You must complete
this initialization
step or your table
will NOT function
properly.
!
Cleaning instructions
To clean the Sierra HX legs, apply cleaner to a soft cloth.
Suggested cleaners: Windex or Formula 409.
Do not use solvents and do not saturate or spray cleaners directly to table base.
Hold down the down
arrow until table moves
slightly upwards
Connect Power Cord to the Power Supply and put workcenter upright
Connect the Power Cord (S) to the Power Supply.
Turn the table over into an upright position.
Plug the Power Cord into the power outlet.
b
10
a
c
11
12
S
b
ac