Workrite Ergonomics FDEX30-48-X Programming manual

Box1
Box2
Parts Included, Frame Set
Hardware kit, 4225338 (Silver and White) or 4225339 (Charcoal)Companion Leg
Assembly & Installation Instructions:
Fundamentals 2-Leg Workcenter FDEX30-48-X
Required & Sold Separately
Foot Kit
Basic or Programmable Control
Worksurface
G4 mm Allen Wrench
Qty: 1
OPower Supply Qty: 1
NPower cord - 3.5 meters Qty: 1
JCable Spool
Qty: 1
KCable Loops Qty: 5
MLeg Cable - 2 meter Qty: 1
AControl Leg
Qty: 1
BCompanion Leg Qty: 1
CShort Bracket Qty: 4
IFeet Glides Qty: 4
DLe End Bracket Qty: 1
ERight End Bracket Qty: 1
F#M6 × 14 mm Flat Head Cap Screw
Qty: 20
H#12 × ¾" Pan Head Laminate Top Screw
Qty: 26
L#8 × ⅝" Pan Head Screw Qty: 7
BCompanion Leg Qty: 1

2 of 8 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
or
Verify that you have all the tools needed for the assembly
You will need the following tools:
#2 tip Phillips screwdriver or drill/driver
#3 tip Phillips screwdriver or drill/driver
M4 tip bit or 4 mm Allen Wrench (H)
If you do not have a Workrite worksurface, you will also need:
⅛" pilot drill bit
" pilot drill bit
WARNING: Maximum loading of table assembly is 125 lb. (56.7 kg.). Maximum load includes the weight of the
table top itself, any equipment placed upon it, and any equipment suspended or hanging under it. Loading should be evenly distributed
over table surfaces. “Payload Capacity” is the Workrite Ergonomics recommended maximum loading which includes the Workrite sourced
table top.
Fundamentals 2-leg
V = 120VAC, 60Hz / 2.5 A maximum
IMPORTANT SAFETY INSTRUCTIONS:
When using an electrical furnishing, basic precautions should always be followed, including the following:
Read all instructions before using this Fundamentals Workcenter.
DANGER:To reduce the risk of electric shock, always unplug this Fundamentals Workcenter from the electrical outlet
before cleaning.
WARNING:To reduce the risk of burns, fire, electric shock, or injury to persons:
1. Unplug from outlet before putting on or taking o parts.
2. Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled persons.
3. Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by the
manufacturer.
4. Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or
dropped into water. Return the furnishing to a service center for examination and repair.
5. Keep the cord away from heated surfaces.
6. Do not use outdoors.
7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
8. To disconnect, remove plug from outlet.
9. Each surface intended to support an equipment payload capacity of 125 pounds.
FOR COMMERCIAL USE ONLY
SAVE THESE INSTRUCTIONS
✓
IMPORTANT NOTE!
You must complete initialization (Step 11) at the end of
assembly or your workcenter WILL NOT FUNCTION PROPERLY.

Workrite Ergonomics | 800.959.9675 www.workriteergo.com 3 of 8
F#M6 × 14 mm Flat Head Cap Screw
Lay Out Legs & Brackets
Lay Legs (A and B) and Brackets (C, D and E) on the floor.
Attach Short & Medium Brackets
Attach Short Brackets (C) using Allen Wrench (H) and Flat Cap
Screws (J) to both legs. Do not tighten screws completely.
Attach Right End Bracket (D) to sides of the right (Control) Leg (F) using Flat Cap Screws (J). Attach Le End
Bracket (C) to sides of the le (Companion) Leg (G) using Allen Wrench (H) and Flat Cap Screws (J).Do not
tighten screws completely.
Note: the right leg will be on your le and vice versa when the assembly is seen upside down.
E
C
C
C
C
C
C
B
A
To avoid stripping the threads, always
insert and make the first few turns
of the screw BY HAND with an Allen
wrench (H), ensuring it is in straight.
2
Hardware at actual size
1
Le (Companion) leg
Right (Control) leg front
C
E
D
D
C
F
F
F
F
G
F
F

4 of 8 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Needs feet attached
Attach Base to Pre-Drilled Workrite Worksurface
If you do not have a Workrite worksurface skip to Step 4
If you have a Workrite worksurface:
Position leg assemblies to align mounting holes
in brackets to pre-drilled holes in Worksurface
then attach using Pan Head Top Screws (H). If
you use an electric screwdriver, be sure it is on
the lowest torque setting to avoid stripping the
holes in the top.
Tighten all screws connecting brackets to leg
assemblies.
Skip to Step 5.
3
H
H
H#12 × ¾" Pan Head Laminate Top Screw
Hardware at actual size
3 screws per
Short Bracket (C) 4 screws per End
Bracket (D&E)

Workrite Ergonomics | 800.959.9675 www.workriteergo.com 5 of 8
Needs feet attached
6⅛"
6⅛"
2⅞"
2⅞"
Attach Base to Worksurface Non-Workrite Tops
If you do not have a Workrite worksurface:
Position leg assemblies on bottom
side of worksurface 6" from front
of top and 2" from side as shown
in illustrations.
Mark placement of mounting
holes, then use ⅛" drill bit to drill
pilot holes at marked locations.
You may wish to mark your drill
bit so you do not drill any more
than ¾" deep and damage your
worksurface top.
Do not drill all the way through
worksurface!
4
front
Attach Frame Set to top using Pan Head Top
Screws (H). If you use an electric screwdriver, be
sure it is on the lowest torque setting to avoid
stripping the holes in the top.
Tighten all screws connecting brackets to leg
assemblies.
C
H
a
b
b
b
b
a
a
c
cc
d
H
H#12 × ¾" Pan Head Laminate Top Screw
Hardware at actual size
3 screws per
Short Bracket (C) 4 screws per End
Bracket (D & E)
C
D
E

6 of 8 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Attach Cable Spools and Cable Loops
Attach Cable Spool (J) with the #12 × ¾"Pan Head Laminate screw (H) and Cable Loops (K) to underside of
worksurface using #8 × ⅝"Pan Head Screw (L) making sure to wrap the Cable Loop around the cables prior to
attaching. If you DO NOT have a Workrite worksurface, mount cable spools in a convenient location between
legs and control box.
7
Attach Feet (sold separately)
Screw in the four Foot Glides (I).
Refer to foot kit instructions for steps to install your feet.
Attach Control (sold separately)
Refer to control instructions for steps to install your control.
L
K
K
K
H
K
K
J
I
6
5
Programmable Control shown

Workrite Ergonomics | 800.959.9675 www.workriteergo.com 7 of 8
Connect Leg Cables to Control leg and Companion Leg
Connect the Leg Cable (M) to the six position connector labeled “1” on both the Control Leg and the Companion
Leg (B).
Insert the Power Cord (N) into the two position connector labeled “DC” on the Control Leg.
Insert the Control Cable into the data connector labeled “A1” on the Control Leg.
8
N
B
A
M
M
Control Cable
Control Cable
N
Control Leg
Companion Leg

8 of 8 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
#1500211- Rev B
Initialize Legs
Aer all legs and the control are connected, and the power cord has been plugged in, hold the down arrow on
the control until the legs make a short motion down and then back up. This initializes and synchronizes the
table legs.
Adjust Feet Guides
If necessary, adjust leveling guides on table feet to level the worksurface. Unscrew to increase height, screw in to
decrease height.
Cleaning instructions
To clean the legs, apply cleaner to a so cloth.
Suggested cleaners: Windex or Formula 409.
Do not use solvents and do not saturate or spray cleaners directly to table base.
Hold down the down arrow until table
moves slightly upwards
Connect Power Cord to the Power Supply and put workcenter upright
Connect the Power Cord (R) to the Power Supply (S).
Turn the table over into an upright position.
Plug the Power Cord into the power outlet.
Never connect or remove leg or
control cables when power is
connected! Doing so will damage
the Control Leg.
You must complete
this initialization step
or your table will NOT
function properly.
10
11
b
9
a
c
✓
a b c
N
O
O