Workrite Ergonomics Sierra Series User manual

#1500152-Rev B Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Sierra Series Workcenters
Special Settings
Before continuing, initialize legs if you have not done so already
After all the legs and the switch are connected and the power cord has been plugged in, hold the
down arrow on the switch until the legs make a short motion down and then back up.
This initializes and synchronizes the table legs.
or +
23
1
5
10
15
20
25
3035
40
45
50
55 60
You must complete
this initialization
step or your table
will NOT function
properly.
Hold down until
table moves
slightly upwards.
Change display from inches to centimeters
Simultaneously press 1 & 2 and the Up or Down Arrow until the readout changes to show S5.
Press the “SET” button with a ballpoint pen (NOT paperclip) to change from inches to centimeters.
To return to inches, repeat the same process.
a
b
or +
23
1
5
10
15
20
25
3035
40
45
50
55 60
a b

#1500152-Rev B Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Sierra Series Workcenters - Special Settings
Adjust Starting Digital Height Readout
(If you have a worksurface that is not 1⅛" thick, causing the lowest height readout to be incorrect)
Lower the table to the lowest position and measure the height from the oor to the top of the
worksurface. (not shown)
Press the “SET” button with a ballpoint pen (NOT paperclip).
Press and hold “Down” button until display ashes.
Press “Up” or “Down” button until display shows actual height for the worksurface.
Press the “SET” button with a ballpoint pen (NOT paperclip).
Note: Height readout must be readjusted separately for inches and centimeters.
Table Locking Feature
To Lock:
Press and hold the “SET” button with a ballpoint pen until the control box clicks two times –
The table will now be locked and will not move when any buttons are pushed. A padlock icon will
appear on the display when the table is locked.
To Unlock:
Press 1, then 2 and then 3 to unlock. *The default unlock code is always 1-2-3.
a
b
or +
23
1
5
10
15
20
25
3035
40
45
50
55 60
b
a
b
c
d
e
or +
23
1
5
10
15
20
25
3035
40
45
50
55 60
b c
d
e
a

Workrite Ergonomics | 800.959.9675 www.workriteergo.com #1500152-Rev B
Sierra Series Workcenters - Special Settings
Set Custom Height Limits
You can set custom limits for both the upper and lower height range.
A custom upper height limit must be higher than 35” and the custom lower height range must be
below 35”.
You can set just an upper or lower custom height limit - it is not necessary to set both an upper
and a lower height limit.
To set or delete a new lower limit:
Move to the desired lower limit anywhere lower than 35 inches
Press the following buttons at the same time for about 4 seconds:
Button 1, Button 2 and the Up Arrow
If the code “S 4” appears release all Buttons and then press Button 1 to set this custom lower limit
or Button 2 to delete this custom lower limit
OR
If any other code appears in the display, release the buttons and then press either the Up or the
Down button until the display reads “S 4” and then press Button 1 to set this custom lower limit or
Button 2 to delete this custom lower limit
To set or delete a new upper limit:
Move to the desired upper limit anywhere higher than 35 inches
Press the following buttons at the same time for about 4 seconds:
Button 1, Button 2 and the Up Arrow
If the code “S 4” appears release all Buttons and then press Button 1 to set this custom upper limit
or Button 2 to delete this custom upper limit
OR
If any other code appears in the display, release the buttons and then press either the Up or the
Down button until the display reads “S 4” and then press Button 1 to set this custom upper limit or
Button 2 to delete this custom upper limit
a
b
c
or +
23
1
5
10
15
20
25
3035
40
45
50
55 60
b
a
b
c